CamPilot MRH310 User manual

1
Adapter and LAN cable are not included in the package.
CamPilot MRH310
IP
H Vandal ome
Camera
User Manual
Before installing and using the product, please read
this manual carefully.
Be sure to keep it handy for later reference.
etail Model Name
MRH310 - CP11MV - T N5 - 18IR
MRH310 - CP11MV - VF - T N5 - 18IR
D i g i t a l D N A m a k e s y o u D I VA
▶
▶▶
▶
MRH310
-
CP11MV
Camera and IR module
The IR LED equipped model
complements
the weakness of CMOS
sensor on a low li ht environment. It
provide the ima e that corresponds to
CCD on a low li ht environment.
2
Precaution
WARNING
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK,
O NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTIONS
■ o not open or modify
Do not open the case, as it may be dan erous and cause dama es.
■ o not put objects inside the unit
Make sure that no metal objects or flammable substances et inside the camera. It could cause
fire, short-circuits or dama es.
■ Be careful when handling the unit.
To prevent dama e, do not drop the camera or subject it to stron shock or vibration.
■ Install away from electric or magnetic fields.
■ Protect from humidity, dust and high temperature.
CamPilot MRH310 is for indoor use and vulnerable to water and/or moisture.
An additional case that is temperature-controllable, damp-proof and waterproof is required for
outdoor use.
■ Cleaning
Dirt can be removed from the case only by wipin it with a soft cloth moistened with a soft
deter ent solution.
■ Mounting Surface
The mountin surface material must be stron enou h to support the camera.
■ CamPilot MRH310 can be used for surveillance purpose.
Be thorou hly informed of related re ulations prior to installation to ensure compliance with such
re ulations.
3
Overview
Features
CamPilot MRH310 is an IP Camera that transmits real-time hi h-resolution di ital video
and audio data with H.264 hi h compression rate over Internet or Intranet.
CamPilot MRH310 contains di ital video/audio compressor, web server and network
interface. Users can simply connect power source and network cable for operation.
Additional operation equipments or pro rams are not required.
Appearance and Accessories
• Ethernet port supports PoE
• Power cable: 2 pin connector
• Audio cable: Ø 3.5mm stereo jack for Audio IN/OUT (RCA type)
(White – Speaker / Red – Microphone, Both should be amplified for use)
• Video cable: pin connectors for video loop throu hout
• A wrench for removin the dome cover and 4 screws for installin the dome are included in
the packa e
• Optional accessories: Pin connectors for Di ital IN/OUT and RS485 are optional items on
order.
▶ Appearance ▶ Accessories
Power Cable
2 pin connector
Audio Cable
(W-SPK / R-MIC)
Video Cable
(for test)
Optional Accessory
◀
▶ Side ▶ Bottom
4
Specification
Items CamPilot MRH310-CP11MV
Camera
Device OmniVision CMOS
Size 1/4 inch
Effective Pixels 1280 x 720 pixels
Min. Illumination 3300mV / (Lux • sec)
Focus 3.6~16 mm Vari-focal
Auto Iris Control O
IR Cut Filter Remove TDN5
White Balance AWB mode
S/N Ratio 39dB
Encoder
CPU ARM9
Flash Memory 8MB
RAM DDR2, 256MB
OS Embedded Linux
Video Output 1ch. loop-throu hout (pin connector - BNC)
Audio Input / Output 1ch. in / 1ch. out (Ø 3.5mm stereo jack - RCA)
Ima e
Size
NTSC : 720p(1280X720), D1(720X480), 4CIF(704X480), VGA(640x480),
CIF(352x240), QVGA (320x240), QCIF(176x112), QQVGA(160x112)
PAL : 720p(1280X720), D1(720X576), 4CIF(704X576), VGA(640x480),
CIF(352x288), QVGA (320x240), QCIF(176x144), QQVGA(160x112)
Codec H.264, MJPEG
Bandwidth 32Kb~4Mb
Transmission Up to 30fps (at 720p)
Network
Interface RJ45 (10/100 Base-T)
Connection Up to 10
Protocol
TCP/IP, ICMP, HTTP, ARP, SMTP, FTP, PPP, PPPoE, DHCP, NTP, SNMP, UPnP
RTP, RTSP
Firmware Update Available on Web browser
Security
Password Authentication
O
User Authentication O
DIO (Di ital Input / Output) 1 in / 1 out (pin connector, option)
Pan / Tilt / Zoom N/A
Motion Detection O
Dynamic IP support O (DHCP, PPPoE support)
Recordin PC software
FTP, Email Transmission O
Power DC 12V 1A/ AC24V 1A/ PoE (sold separately)

5
Internet
or
Intranet
Installation and Connection
Basic Installation
(1) POWER – DC 12V 1A (No polarity) / AC24V 1A
(When PoE is used, the power is not necessary.)
(2) ETHERNET - LAN cable (RJ45 jack)
(Please, refer to the standard of “IEEE 802.3af”)
Expert Installation
(1) Audio In / Out: Ø 3.5mm stereo jack - RCA.
(2) Video loop throu hout is for test after installation. (D1 output)
(3) Additional accessories on order should be used for Di ital IN/OUT and RS485.
Power
Power
Power
CamPilot MRH310
·
··
· ·
··
· ·
··
·
1 2 N
HUB
General Connection
Monitorin PC Monitorin PC
Local Network
Public Network
LAN (UTP) Cable
LAN (UTP) Cable
LAN Cable
Router
MRH310
-
CP11MV
-
VF
-
IR
◀
◀◀
◀
Pin connector for Power
Audio In
/ Out
Cable Hole
Factory efault
LAN (PoE)
IO
6
Installation and Connection
External evice Connections
REF Monitoring PC Requirements
Item Specification
Monitorin
PC
Processor Pentium Core2 Duo or more
RAM 2GB or more
Graphic Card 512MB or more
OS Windows 2003 / XP / Vista / 7
Monitor Resolution 1024 X 768 pixels or more
Network 10/100 Base-T LAN
External Device Connection
Power
Sensor or Alarm
MIC
Network
Speaker
Audio Cable
Pin connector
LAN cable (UTP)
7
Network Setting
Setting an IP address of a CamPilot MRH310
TIP If a monitorin PC is on 192.168.1.xxx network area, the connection is available without
any chan e on CamPilot MRH310. The initial IP address on CamPilot MRH310 is
192.168.1.2.
In case of the direct connection, the monitorin PC (Note Book) should be chan ed into
192.168.1.xxx
When chan in the network settin , use ENCP pro ram.
1. ownload ENCP (Easy Network Configuration Program)
• Please, refer to the link as below
http://cellinx.co.kr/files/board.3/5_NVS4.1%20(2011.04.06%201121).zip
• After unzippin the downloaded file and executin “Setup.exe”, you can run ENCP.
(Windows start button / All Pro rams / NVS 4.1)
2. Assigning an IP address on CamPilot MRH310
• Click the button “Scan”, select an CamPilot MRH310
• Input the IP address, Subnet Mask, Gateway and NS Server IP address, click the button
“Apply”
• If you don’t have a proper IP address, ask the network administrator or refer to User Manual.
▶
▶▶
▶ Click for Scanning
▶
▶▶
▶ Click
for Applying
8
Network Setting
3. Accessing to CamPilot MRH310 with a web browser
Open a web browser on a monitorin PC and enter the IP address assi ned to a CamPilot
MRH310 as followin
Example> http://192.168.1.2
• The pa e as below shows up after the connection is completed.
ID / Password :
root / pass (Initial Value)
Monitoring button :
moves to Monitorin Pa e
Guest Lo in :
connects by “ uest” account
(The uest has no settin permission)
< The Initial Page >
< Monitoring >

9
Network Setting
Basic Information
The initial IP address of a CamPilot MRH310 is 192.168.1.2, which is an IP address of
192.168.1.xxx (1~255) assi ned to the private network. If a monitorin PC doesn’t have an IP
address of the same network (192.168.1.1~255), the user have to chan e the IP address of the
CamPilot MRH310 (Refer to ENCP at p.7)
Check the IP address of a monitoring PC (network information)
1. Get to a command prompt. (START / run / cmd).
2. Type “ipconfi ” on the command prompt window and press “Enter”.
Determine the IP address for a CamPilot MRH310 after checkin the PC information as table.
REF xxx : the number should not be used for another PC of a same network
The subnet mask and default ateway of a PC on a same network is same to those of a
CamPilor MRH310.
Checking the unused IP address
Type “ping xxx.xxx.xxx.xxx” on the command prompt window and press “Enter”.
If the messa e “Destination Host Unreachable” shows up, we can know that the IP address is
not used. But it is recommended that you should ask the address to the network administrator
for the PC of the IP address is off.
In case that a public IP address is used for the network, you have to ask the extra IP address to
the network administrator.
PC information example CamPilot MRH310 address example
Private
Network
Ex.1
IPv4 address 192.168.10.100
Subnet mask 255.255.255.0
Default Gateway 192.168.10.1
IP address 192.168.10.xxx
Subnet mask 255.255.255.0
Default Gateway 192.168.10.1
Private
Network
Ex.2
IPv4 address 10.0.0.10
Subnet mask 255.255.0.0
Default Gateway 10.0.0.4
IP address 10.0.xxx.xxx
Subnet mask 255.255.0.0
Default Gateway 10.0.0.4
Public
Network
Ex.
IPv4 address 123.150.24.34
Subnet mask 255.255.255.0
Default Gateway 123.150.24.1
IP address 123.150.24.xxx
Subnet mask 255.255.255.0
Default Gateway 123.150.24.1
10
Network Setting
Port forwarding
- Settin the router, in case that one (or more) CamPilot MRH310 is connected.
- The port forwardin should be set for the connection from a public network area.
If a CamPilot MRH310 is installed on a private network, the port forwardin should be set for
the connection from a public network area.
As the port forwardin is a settin item of a router, a PC of the IP address on a public network
can be connected to a CamPilot MRH310 on a private network via the router.
If the port forwardin is set up as below, the function works.
REF Basically the ports 80 and 1852 were used for the web and video connection for a
CamPilot MRH310.
After executin a web browser and typin the IP address that is assi ned to the router, you
can monitor the video of CamPilot MRH310 on a PC on a public network.
REF If you want to use a specific name instead of the IP address of the router, you can use the
DDNS function of a router or a CamPilot MRH310. DDNS function includes updatin an IP
address for a specific name thou h the IP address of the router is chan ed. (Refer to The
function of updatin dynamic IP address at p.11)
11
Network Setting
Port forwarding in case of installing two (or more) CamPilot
MRH310
A port of a router cannot be used for the two (or more) CamPilot MRH310. In this case, another
port number should be added on the router.
Port forwardin example (NVS: Network Video Server)
Port forwardin of Router
NVS port account
Service
Name Private IP Protocol
Service Port
(External Port)
Internal Port
NVS #1-1 192.168.1.100 TCP 8080 8080 8080 - Web
NVS #1-2 192.168.1.100 TCP 2000 2000 2000 – Video + Audio
NVS #2-1 192.168.1.101 TCP 8081 8081 8081 - Web
NVS #2-2 192.168.1.101 TCP 2001 2001 2001 – Video + Audio
NVS #3-1 192.168.1.102 TCP 8082 8082 8082 - Web
NVS #3-2 192.168.1.102 TCP 2002 2002 2002 – Video + Audio
NVS #4-1 192.168.1.103 TCP 8083 8083 8083 - Web
NVS #4-2 192.168.1.103 TCP 2003 2003 2003 – Video + Audio
참고 Thou h the internal ports of CamPilots are used as default in theory, it is recommended
that the service port of the router and the internal port of CamPilot should be same for the
function doesn’t work by the features of a router.
12
Network Setting
The function of updating dynamic IP address ( NS)
1. The function DDNS of CamPilot can be used with the environment of one CamPilot MRH310
and an internet modem.
2. The function DDNS of a router should be recommended in case that there is a router for two
(or more) CamPilot MRH310 or the mana ement (firewall) purpose.

13 14
Web Monitoring
▲
▲▲
▲ OVERVIEW
• User can monitor the video and audio data and mana e CamPilot MRH310 throu h a
web browser over internet.
• User can select a type amon encoder mode and decoder mode throu h a web
browser.
• Basic functions
- Monitorin the video and audio data from a CamPilot MRH310.
- Chan in the setup related to monitorin
(Resolution, Info. display, D/O (Di ital Output), Bitrate, Audio, PTZ, and etc.)
- Confirmin the status of a CamPilot MRH310
(Network Status, Model Info, Connection List, Lo )
- Chan in the basic settin (Network, Video, Audio, Event, Date/Time, OSD)
- Chan in the expert settin (RS485, RS232, Port, Security Level, Account,
DDNS, UPnP, Motion Detect, Firmware Update)
Monitoring
Managing
< The initial page >
15
Web Monitoring
▲
▲▲
▲ CONNECTION
• To connect to a CamPilot MRH310, type the IP address that is iven to the CamPilot
MRH310 on the address window of a web browser as below.
(Refer to “ENCP 2.1” pro ram manual to set an IP address of the CamPilot MRH310)
• Connection and accounts
① Administrator account
- It is available to monitor and mana e a CamPilot MRH310.
- The Default I / Password of the administrator is root / pass.
- Only the password is chan eable. (Administrator’s ID is fixed.)
② Guest account
- It is available to use only the functions that are permitted limitedly on monitorin .
- It is shown as inactivated for the limited functions on monitorin pa e.
http:// (IP Address of CamPilot MRH310)
http:// 192.168.1.2
► Type on the address window of a web browser and enter
► Example (Default IP Address)
► Lo in window
16
Web Monitoring
Setting page login
: Type the ID and Password of the administrator and click “Settin ” button.
Monitoring page login
: Type the ID and Password of the administrator and click “Monitorin ” button
Guest login
: Click “Guest Lo in” to enter the monitorin pa e of uest account
► Monitorin Pa e
► Server Settin Pa e

17
Web Monitoring
• Note for Monitorin Pa e
- When first connectin to monitorin pa e, click “Yes” to download ActiveX if
“security warnin ” window appears. (CASE ① )
- Click the yellow information bar to download ActiveX control.
①
②
②②
②
①
①①
①
18
Web Monitoring
- User can download and install ActiveX Setup manually if the information bar
does not appear. (CASE ② )
- Click “Run” button to install ActiveX file manually (NVSOCX.exe)
► ActiveX Setup window
19
Web Monitoring
▲
▲▲
▲ MONITORING
• 1st / 2nd / 3rd Stream
- Selects a Stream to monitor
- If the stream button is inactivated, check the video settin of “server settin pa e”.
• Snapshot
- Captures a JPEG Ima e of current video stream
(JPG file creation route : C:/root)
Monitoring Page
20
Web Monitoring
• REC
- Records the video of current video stream (AVI file creation route : C:/root)
• Full
- Extends the ima e of current video stream to fit monitor size.
• Resolution
- Displays a current resolution.
- User can select other resolution.
(If CamPilot MRH310 is rebooted, the resolution on the monitorin pa e is initialized
to the desi nated value of “server settin pa e”.)
- Chan in the resolution is not available on a uest account.
• Info.
- Shows the information of the transferred data from the CamPilot MRH310 on the
upper of the ima e.
- FPS / Camera(Channel) Name / Resolution
- Event Status : Motion Detect(red) / Di ital IN(blue) / Video si nal ( reen)
Resolution
QQVGA QCIF QVGA CIF VGA 4CIF D1 720p
NTSC 160X112
176X112
320X240
352X240
640X480
704X480
720X480
720X1280
PAL 160X112
176X144
320X240
352X288
640X480
704X576
720X576
720X1280
Detect video si nal
Detect motion event
Detect sensor input (Di ital IN)
FPS of current video stream
Resolution of current ima e
Channel name

21
Web Monitoring
• /O
- Di ital Out - This controls the device that is connected to CamPilot MRH310.
• Bitrate
- Display the bitrate of current video stream.
- User can select other bitrate. (If CamPilot MRH310 is rebooted, the bitrate on the
monitorin pa e is initialized to the desi nated value of “server settin pa e”.)
- Chan in the bitrate is not available on a uest account.
• Enable Audio
- If the box is checked the CamPilot MRH310 sends the audio data with the video data.
• PTZ Control
- User can control a PTZ camera or receiver throu h RS485
• Z (Zoom): zoom in (+) / zoom out (-)
• Pan/Tilt : CamPilot MRH310 does not support Pan/Tilt function
• F (Focus): focus in (+) / focus out (-)
• PTZ control is not supported on a uest account
- CamPilot MRH310 does not support PTZ function internally.
22
Web Setting
▲
▲▲
▲ SERVER SETTING
- To apply the chan ed settin , reboot CamPilot MRH310.
(Click Reboot on the menu)
• Status
- This is the initial pa e of Server Settin .
- This shows network status, model information, network traffic status,
connection list and system lo .
23
Web Setting
• Network Status
- MAC Address: Media Access Control Address of CamPilot MRH310 (Unchan eable)
- IP Address: the assi ned IP Address of CamPilot MRH310
- Subnet Mask: Subnetwork of the IP address belon s to.
(Use the value to fit the network environment)
- Gateway: Gateway Address (Use the value to fit the network environment)
- Default DNS: IP Address of Default DNS server
• Connection List
- User can check the number of connected clients and IP addresses.
• Log
- “Lo ” displays the lo s of eneral events of CamPilot MRH310.
• Basic > Network (Wired)
- User can set Network Information of CamPilot MRH310: IP Address, Subnet Mask,
Gateway, Default DNS
①
①①
① Static IP
24
Web Setting
- IP Address: Ask network administrator for an appropriate address
- Subnet Mask / Gateway / Default DNS : Ask network administrator
- After settin , click “OK” button
- Click “Reboot” to apply the settin to CamPilot MRH310.
②
②②
② ynamic IP
- If DHCP server is on the local network and you intend to allocate IP address dynamically,
use this method
- Select ynamic IP tab and click “OK” button, and reboot CamPilot MRH310.
- If you want to select ynamic IP, set Dynamic DNS to access CamPilot MRH310.
Click!
< Reboot Messa e >

25
Web Setting
③
③③
③ PPPoE
- Use in case that the network supports PPPoE like xDSL
- Ask ISP(Internet Service Provider) for details
- User ID : xDSL user ID
- User Password : xDSL user password
- Service Name : Service name of ISP
- MTU : Maximum transmission unit of data
- IP address of DNS sever can be set to create automatically
- If your xDSL does not use static IP type, you should use Dynamic DNS settin like
DHCP
26
Web Setting
• Basic > Video
< Video Settin Pa e >
27
Web Setting
Video Setting
- Preview : User can check the current video settin throu h the preview ima es.
(1st / 2nd / 3rd stream selectable)
- Video Compressed Type: H.264 / MJPEG
(Compression type of 3rd stream : MPEG4)
- Resolution : QQVGA / QCIF / QVGA / CIF / VGA / 4CIF / D1
(Resolution of 3rd stream : QCIF fixed)
- Bitrate Type : CBR / VBR
• Constant Bitrate : 8M / 7M / 6M / 5M / 4M / 2M / 1.5M / 1M / 750K / 500K / 384K /
256K / 128K / 64K / 32K
• Variable Bitrate : 1~6 (The hi hest quality is “1”)
- Frame Per Sec : 1 ~ 30 (NTSC) / 1~25 (PAL)
- Group Size : 1~200 (NTSC / PAL)
- Port : Video and Audio streamin port (Each stream must use different port)
- Video Type : NTSC / PAL
- Video Color : Auto / Color / B&W
- Aperture : 0~15 (Max. emphasis value is “15”)
- Bri htness / Contrast / Saturation / Hue : 0~255
- X / Y offset : 1~21
Jpeg Capture
- Enable : Sends JPEG Ima e via HTTP Protocol (1fps fixed)
- Resolution : Select a resolution (QQVGA~D1)
- Quality : Hi h / 1 / 2 / 3 / 4 / Low
▶ Jpe Capture
28
Web Setting
MEMOS
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________
_____________________________________________

29
Web Setting
• Basic > Audio
Server to PC Audio Option
- Audio Type : Mono (Fixed)
- Audio Codec : G.711 / G.726
- Samplin Rate : 8kHz / 32kHz
- Volume : -34.5~12dB
30
Web Setting
• Basic > Event
①
①①
① igital Input
31
Web Setting
Common
- Sensor Type: Select a type out of two types.
Preset
- Preset Enable: enables the CamPilot MRH310to send the preset si nal to the connected
camera which supports preset function
- Preset Number: preset number that assi ned to the camera which supports preset
function
igital Output
- Di ital Output Enable: enables the CamPilot MRH310to send the di ital si nal to the
connected device
- Di ital Output Time: adjusts the time for the CamPilot MRH310to send the si nal (unit :
sec)
FTP
- Enable: enables the CamPilot MRH310to send captured ima e to FTP server
(Assumin JPEG Capture enable on the video settin pa e)
- Server : IP address of FTP server
- Port : FTP server port
- User : Account of FTP server
- Password : Password of FTP server
- Ima e name : File name of captured ima e
(Time information will be added with the ima e name.)
SMTP (e-mail)
- Enable: enables the CamPilot MRH310 to send captured ima e via e-mail.
- Out oin mail server : SMTP Server
- To e-mail address : e-mail address of receiver
- From e-mail address : e-mail address of sender
- Subject : User can specify e-mail title
- Body : User can specify e-mail massa e
32
Web Setting
②
②②
② Motion etection
Preset : Same as “Di ital Input” settin
igital Output : Same as “Di ital Input” settin
FTP : Same as “Di ital Input” settin
SMTP (e-mail) : Same as “Di ital Input” settin

33
Web Setting
Periodic Timer ③
③③
③
Common
- Periodic Timer Enable : enables the CamPilot MRH310 to send the si nal to the client
PC periodically
- Time Interval : means the period (sec.)
Preset : Same as “Di ital Input” settin form
igital Output : Same as “Di ital Input” settin form
FTP : Same as “Di ital Input” settin form
SMTP (e-mail) : Same as “Di ital Input” settin
34
Web Setting
• Basic > ate / Time
Current Time Set ①
①①
①
ate / Time
- S- Server Time : the time that the CamPilot MRH310 keeps internally
- New Date / Time: user can assi n the specific time voluntarily.
35
Web Setting
②
②②
② Time Server
Time Server
- Enable : enables the time of CamPilot MRH310 synchronize with time server periodically.
- Interval : means the period (sec.)
- Time zone: user can select a time zone
- Dayli ht Savin Time : Check this box in usin dayli ht savin time
- Time Server: user can assi n a Time Server to apply the current time to CamPilot
MRH310
- After settin , click the “OK” button and reboot CamPilolt.
36
Web Setting
• Basic > OS (On Screen isplay)
Text Color
- Back round Color : Select a color of back round
- Fore round Color : Select a color of text
- Transparency : 0~10

37
Web Setting
OS
- Font Size : Normal / Bi
- Date Enable : display date
- Time Enable : display time
- Channel Enable : display channel name
- X Axis: Input a point on the coordinate
- Y Axis: Input a point on the coordinate
Logo
- This means the ima e that is displayed on OSD of the transferred ima e.
- First, upload the lo o ima e on “Expert/Firmware Update/OSD lo o upload” (BMP file)
- Enable: Check the box to display the ima e
- X Axis: Input a point on the coordinate
- Y Axis: Input a point on the coordinate
► OSD on ima e
Date / Time / Channel Name
OSD lo o
38
Web Setting
• Expert > Camera Setting
Color Mode
- “Auto” is recommended.
Brightness/Contrast/Sharpness
- Other values are available on a
specific environment.
Power line frequency control
- refer to the power supply
environment and select one.
Frame rate control
- Fixed mode: 30fps
- DSS mode: makes Di ital Shutter
Speed chan e on the li ht
environment. (Lower FPS can have
more li ht than Hi her FPS)
BLC (Back light control)
- ”ON” makes bri htness optimize
Indoor / Outdoor
- Select the installation place.
Mirror / Flip
- makes the video mirror or flip.
ISP firmware update ver. 11.10.00.00
- This is used for technical support. Please don’t chan e anythin on this item.
• Expert > PTZ (This function is available on RS485 communication)
Channel 1
- Channel Name : the channel name of
OSD
- Channel Model (PTZ model)
: Select a model of the connected PTZ
camera or receiver
- Channel ID (Rx Address)
: the Rx address of the connected PTZ
camera or receiver
- Baud rate / Data bits / Parity / Stop
bits
: select the value properly by the
receiver type
39
Web Setting
• Expert > Local Storage (Optional)
- A mirco SD card is automatically mounted when it is inserted into the SD / SDHC card
slot. (The function of CamPilot MR310 will be applied from July, 2011)
Status
- Displays the total space, used space and free space of SD / SDHC Card.
Record Setting
- Mode: Select a record type (OFF / Full Recordin / Event Recordin )
- Select a video stream of CamPilot MRH310 (1st / 2nd / 3rd Stream)
- Select a overwrite settin of the local stora e (ON/OFF)
File list
- A recorded file is made by 10MB size.
- User can download and delete the recorded file.
40
Web Setting
• Expert > Port
Web
- Web Port: Default is 80
FTP
- FTP Port: Default is 21

41
Web Setting
• Expert > Security
Security Level
- HIGH
: Only connections from the local area are permitted
- MEDIUM
: Video and Audio connections from any place and settin from the local area permitted.
- LOW
: All connections from any place permitted
42
Web Setting
• Expert > Account
Account
- The password amendment of administrator account is available.
- The administrator can add up to 5 users and modify the properties.
Guest Permission
- This is to determine the uest permission for access to the CamPilot MRH310
- At uest account, video and audio monitorin is permitted.
Max Client Limit
- The administrator can restrict the number of simultaneous access (1~20)
43
Web Setting
• Expert > NS
- DDNS is the function that matches an IP address and a host name.
- If a CamPilot MRH310 has the dynamic IP address, the host name by DDNS (Dynamic
Domain Name Service) must be used instead of the IP address for the credibility of the
network connection.
IPv4 NS
- Check the box of “Enable” and select a service out of DynDNS and ddns.nu
- Both are required to re ister some items on each service site.
- ProutDNS can be selected in case that a user makes a DDNS server with
ProutDNS.open source.
44
Web Setting
yn NS
- For use of “DynDNS”, re ister account information at www.dyndns.com/
- Type the re istered DDNS ID, DDNS Password, Host name and Interval for updatin on
the CamPilot MRH310. Click “OK” button and reboot the CamPilot MRH310.
.
▶ Main pa e of “DynDNS”

45
Web Setting
ddns.nu
- For use of “ddns.nu” re ister account information at www.ddns.nu
- Type the re istered DDNS ID, DDNS Password and DDNS handle on the CamPilot
MRH310. Click “OK” button and reboot the CamPilot MRH310
Prout NS
- ProutDNS is a set of PHP scripts to create your own Dynamic DNS service.
- Type the DDNS server, the re istered DDNS ID, DDNS Password, Host name and
Interval for updatin on the CamPilot MRH310. Click “OK” button and reboot CamPilot
MRH310.
▶ Main pa e of “ddns.nu”
▶ Main pa e of “ProutDNS”
46
Web Setting
• Expert > UPnP
UPnP
- Enable : Check the box to use UPnP(Universal Plu and Play) of CamPilot MRH310
- Friendly name : User can chan e the friendly name of CamPilot MRH310
47
Web Setting
• Expert > Motion etect
Input Setting
- Check “Enable” box for use of motion detection
- Detect Area: if the detection area is selected, it chan es to reen (User can check
preview ima e assumin JPEG Capture enable on the video settin pa e.)
- Sensitivity : 1~30 (Maximum sensitivity in case of the value “1”)
48
Web Setting
• Expert > Firmware Update
Language
- Lan ua e Select : Select a lan ua e and click the “Set” button
(After that, it is required to refresh the web browser. Please push F5 button.)
Firmware Update
- Uploads the downloaded firmware after clickin the “Browse” button and choose it.

49
Web Setting
Logo Upload
- Chan es the lo o ima e.
- For the process, refer to that of “Firmware Update”
- The filename must be “lo o. if” (Maximum size : 567x175)
OS Logo Upload
- Chan es the lo o ima e on OSD.
- For the process, refer to that of “Firmware Update”
- The filename must be “osd_lo o.bmp” (Maximum size : 120x38)
<Makin “osd_lo o.bmp” with Windows Paint>
Control Protocol Upload
- A user can add the protocol of a PTZ camera or a receiver.
- Please ask the supplier of CamPilot MRH310 for the protocol.
- For the process, refer to that of “Firmware Update”
50
Web Setting
• Expert > Report
Report
- Click the item to check all settin values of CamPilot MRH310.
- It is available to take a memo on the “MEMO” area of the report pa e.
- It is available to print out these pa es. Click the “Print” button.
• Reboot
- To apply the chan ed settin , reboot CamPilot MRH310.
• Logout
- Back to the initial connection pa e
► Confirmation Dialo
51
Trouble-shooting
Before sendin the CamPilot MRH310 out for repair, check the items below.
If the problem persists after checkin these items, contact your service center.
▲
▲▲
▲ If no image appears
- Is the LAN cable attached securely?
- Are the power and volta e normal?
- Is the connected camera normal?
- Is there adequate illumination?
▲
▲▲
▲ If the image is unclear
- Is the connected camera lens in focus?
- Is the connected camera lens dirty?
- Dirt or fin erprints on the lens can adversely affect the ima es.
Gently wipe any dirt or fin erprints off the lens with a soft cloth or lens
cleanin paper and cleanin fluid (commercially available).
- Is the connected monitor adjusted correctly?
▲
▲▲
▲ If the Audio is not work
- Is the audio cable attached securely?
- Are the connected devices(amplifier, microphone, speaker and etc.) normal?
- Are the Client software and devices normal?
▲
▲▲
▲ If the PTZ control is not work
- Is the RS485 cable attached securely?
- Is the connected PTZ Camera or PTZ driver normal?
- Is the RS485 control settin (Protocol, Baudrate, Control ID and etc.) correct?
▲
▲▲
▲ If the IO is not work
- Is the DIO cable attached securely?
- Is the connected sensor or alarm device normal?