car CAD-FMX500 User manual

User Manual
Manual de Usuario
FM Transmitter Phone Mount
CAD-FMX500

EN 1
Important Safety Instructions
Read these instructions, keep these instructions, heed all warnings, follow
all instructions.
1) Ensure that the CAD-FMX500 is mounted in a place that does not block
your view of the road.
2) Do not use this apparatus near water.
3) Clean only with a dry cloth.
4) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
5) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
6) Protect the power cord from being walked on or pinched, ensure that the
power cord does not get tangled with the gas or break peddles.
7) Only use attachments/accessories specified by the manufacturer.
8) Unplug this apparatus during lightning storms or when unused for long
periods of time.
9) Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.

EN 2
FCC NOTICE TO USERS:
FCC ID: 2AMSOSTW001
Caution: Changes or modifications not expressly approved by the Party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection Against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications,
however there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o
ffand on, the user is encouraged to try to correct the interference by one or
more of the following:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for Help.
The device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

EN 3
Box Contents
CAD-FMX500
Vent Mount
Dash Mount
User Manual
AUX Cable
USB Car power adapter
Charging Cable

EN 4
Overview
1. Adjustable gripper (side)
2. TF card slot
3. FM wheel
4. Multifunctional button (Play/Pause; Hang
up/Answer; Siri/Google Voice Assistant)
5. Mic
6. Type-C 5V charging port
7. Gripper release button
8. Adjustable gripper (side)
9. USB port
10. BASS button
11. Mode switch button (BT, TF, USB)
12. LED display
13. AUX OUT jack

EN 5
Mounting
1. Turn the mounting nut counter clockwise to loosen the clamp.
2. Insert the ball knob with clip and clip button into the clamp on the charger
base, and turn the nut clockwise to tighten the ball knob.
3. Press the Clip button to open the clip to fix on the air vent window of your
car. You can turn the ball knob to adjust your desired angel for the phone
mount.
4. Press the Release button on the upper right of the phone mount to unlock
the adjustable gripper (side).
5. Place your phone onto the charging pad, and adjust the two adjustable
grippers (both sides) to lock your phone in place.
1. Turn the mounting nut counter clockwise to loosen the clamp.
2. Insert the dash mount with suction cup into the clamp on the phone
mount, and turn the nut clockwise to tighten the ball knob.
Clip button Mounting nut
Ball knob
Clamp
Clip
You can mount your CAD-FMX500 with either of these methods:
Method 1: Vent mounting
Method 2: Dash mounting

EN 6
3. Remove the protective film from the adhesive suction cup on the bottom
of the mount. Then press the suction cup onto your dashboard and push the
lock down to secure it in place. Adjust the CAD-FMX500’s angle and height
so that it does not block your view of the road, and tighten the knob to secure
it in place.
4. Press the Release button on the upper right of the phone mount to unlock
the adjustable gripper (side).
5. Place your phone onto the charging pad, and adjust the two adjustable
grippers (both sides) to lock your phone in place.
Powering on
To power on this device, connect one end of the supplied USB - Type C
cable to the CAD-FMX500’s Type C port, and the other end to the
supplied car power adapter. Plug the Car power adapter into your
car’s DC power outlet. Once turned on, the word “HI” will appear on the
LED display. Then after 2 seconds, the word “bt” will flash on the display of
this device for pairing.
To your car’s DC
power outlet
Lock Open
Lock Closed
Tighten Knob

EN 7
Bluetooth Mode
To play the music from your phone, you need to pair your phone with the
device. When pairing for the first time, follow the steps below:
1. Make sure the device is powered on.
2. Open your phone’s Bluetooth settings.
3. Search “CAD-FMX500” from your bluetooth list, and tap it to connect.
4. Three seconds after connected, the display will return to FM status.
5. Turn on the car’s radio, and choose an unoccupied radio station. Then
push the FM wheel on the device for one second until the LED display
flashes the frequency.
6. Turn the button up/down to match the same frequency. Once done, you
can play the music from your phone. Use the “play/pause button to play or
pause the music.
Note: This device has auto power-off memory function, which means it will
remain the same FM frequency the next time it turns on, so you do not need
to match the frequency again unless you change it on either your car’s radio
or this device during previous use.
If someone calls you while you’re playing music, this device will automati-
cally switch to telephone mode.
When you use the aux cable, you can play the music from your phone
without matching the device’s FM frequency the same as the car’s.
Plug one end of the aux cable into the AUX OUT port of your phone mount,
and the other end into the car’s radio aux port. Then press the “Mode
Switch” button until the LED display will show the word “AUH” to indicate
the aux status. You are now ready to enjoy your music.
1. For Phone Call mode
2. For Aux mode
Press the Play/Pause button twice
Press the Play/Pause button once
Press and hold the Play/Pause button for two seconds
Answer/End a call
Reject a call
Redial a call

EN 8
3. For U-disc/TF Player mode
Insert your TF card/U-disc into the TF slot/U-disk port of the device, and
then press the “Mode Switch” button until it switches to the correct mode
(For a TF card, the word “sd” will appear on the display, and you will hear
a “SD Card Mode” sound notification; for a U-disc, the LED indicator will
display the word “usb”, and a “USB Mode” sound prompt can be heard). The
music you save on your TF card/U-disc will begin playing automatically.
Bass Function
Press the “Bass” button to switch between normal and bass mode (On the
LED display, H0 means normal mode, H1 means bass mode).
Activate Siri/Google Voice Assistant
Press and hold the “Play/Pause” button for 2 seconds to activate Siri/
Google Voice Assistant.

EN 9
Model name CAD-FMX500
Rated working voltage 5V
Limit working voltage 4-5.5V
Product input 12/24V
Charger output 5V/2.1A
Power consumption 1W
Working temperature 0~50°C
Support file format MP3 / WMA/WAV
SNR > 60dB
Degree of distortion < 0.1%
Frequency response 20Hz-15Khz
Left and right channel (dB) > 60dB
Bluetooth version Version 5.0
Bluetooth sound processing DSP and A2DP(Advance Audio
Distribution Profile)
Bluetooth range 10M
Microphone range 0.5~2M
Transmit frequency 87.5~108.0MHz
Transmit frequency modulation
mode
Stereo digital PLL frequency lock
Memory card (Max capacity) 32GB
Specifications

EN 10
Disclaimer
Notice
CAR AND DRIVER IS A REGISTERED TRADEMARK OF HEARST COMMUNI-
CATION, INC. AND USED UNDER LICENSE BY SUMMIT ELECTRONICS, LLC.
©2021 HEARST COMMUNICATION, INC. ALL RIGHTS RESERVED AND ANY
USE OF SUCH MARKS BY SUMMIT ELECTRONICS LLC IS UNDER LICENSE.
OTHER TRADEMARKS AND TRADE NAMES ARE THOSE OF THEIR RESPEC-
TIVE OWNERS.
WARNING: CANCER AND REPRODUCTIVE HARM - WWW. P65WARN-
INGS.CA.GOV.
All information, design and specifications contained in this manual were cor-
rect at the time of this publication. As the product goes under continuous up-
grades and changes, however, the final device may have slight differences. The
contents of this manual are subject to change without prior notice, and CAR
AND DRIVER will not be liable for any errors contained herein or for incidental
or consequential damages in connection with the furnishing performance or
use of this manual.
This symbol means the product must not be discarded as house-
hold waste, and should be delivered to an appropriate collection
facility for recycling.
Follow local rules and never dispose of the product with normal
household waste. Correct disposal of old product helps prevent
negative consequences for the environment and human health.

SUMMIT ELECTRONICS LLC LIMITED WARRANTY (“Warranty”) - For Prod-
uct Categories Listed in Chart Below (as applicable, “Product”) Before return-
ing your Product for service under this Warranty, please (i) read the instruction
manual carefully. If you are still having trouble with your Product, please con-
tact Technical Support at [email protected]
Warning: Some Products may contain components that are small enough to be
swallowed. Please keep out of reach of children.
Subject to the terms and conditions herein, SUMMIT ELECTRONICS LLC
warrants to the original purchaser of the Product (“Customer”) that for the
applicable Warranty Period listed below, the Product will be free from defects
in material or workmanship under normal, non-commercial use (“Defects”).
Warranty Period encompasses, as listed below, separate “Coverage Periods”
for Parts and Labor, each Coverage Period for one year, to begin from the
original date of Customer purchase. If Customer returns a defective Product
(or any component thereof) during the applicable Warranty Period, SUMMIT
ELECTRONICS LLC will, as its option, during the specified Coverage Periods
for Parts and Labor (as applicable) either: (i) repair the Product (or, as appli-
cable, any component thereof) or (ii) replace the Product (or, as applicable,
any component thereof) with a new or refurbished Product (or, as applicable,
any component thereof), in either case free of charge to Customer for Parts
and/or Labor (as applicable) during the specified Coverage Period only, and
excluding applicable shipping charges (noted below), for which the Custom-
er is responsible. The foregoing states the Customer’s exclusive remedy and
SUMMIT ELECTRONICS LLC’s sole liability for breach of the limited warranty
contained herein.
This Warranty specifically excludes any Product (or, as applicable, any compo-
nent thereof) that has been subject to or Defects resulting from: (a) any neglect
or misuse by a Customer, an accident, improper application, violation of operat-
ing instructions for the Product, any other Customer-induced damage, or the al-
teration or removal of any Product serial number; (b) any modification or repair
to Product (or, as applicable, any component thereof) by any party other than
SUMMIT ELECTRONICS LLC One Year Limited Warranty
EN 11

SUMMIT ELECTRONICS LLC One Year Limited Warranty
SUMMIT ELECTRONICS LLC or a party authorized in writing by SUMMIT ELEC-
TRONICS LLC; (c) any damage to Product (or, as applicable, any component
thereof) due to power surges, incorrect electrical voltage, misconnection to any
device, or malfunction of any device used with the Product (or, as applicable,
any component thereof); (d) cosmetic damage to the Product (or, as appli-
cable, any component thereof) caused by normal wear and tear; (e) shipping
damage that occurs while the Product is in transit; (f) damage caused by heat
sources, sunlight, electromagnetic conditions, or other climatic conditions; or
(g) any acts of God. Product is sold to Customer for personal, non-commer-
cial use only. Product is not warranted for Customer’s commercial or rental
use. In addition, Product is not warranted against failure, and should not be
used by Customer for any application where (i) there is a risk that any data
stored on Product will be breached or otherwise compromised, or (ii) the
data stored on Product is relied upon for medical or lifesaving applications.
SUMMIT ELECTRONICS LLC disclaims any Warranty for any of the foregoing
uses to the fullest extent permitted by law. Customer assumes any and all
risks associated with such uses of Product, and agrees to indemnify SUMMIT
ELECTRONICS LLC for any damages claimed against SUMMIT ELECTRONICS
LLC for such uses. EXCEPT FOR EXPRESS WARRANTIES STATED ABOVE
AND TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE PRODUCTS
ARE PROVIDED “AS IS”, AND SUMMIT ELECTRONICS LLC DISCLAIMS
ALL OTHER WARRANTIES, INCLUDING WITHOUT FITNESS FOR A PAR-
TICULAR PURPOSE, LIMITATION ANY IMPLIED WARRANTY (I) OF MER-
CHANTABILITY, (II) OF OR (III) OF NON-INFRINGEMENT OF THIRD PARTY
RIGHTS. TO THE MAXIMUM EXTENT PERMITTED BY APPLICA BLE LAW,
IN NO EVENT WILL SUMMIT ELECTRONICS LLC BE LIABLE TO CUSTOMER
OR ANY THIRD PARTY FOR ANY INDIRECT, SPECIAL, INCIDENTAL, CONSE-
QUENTIAL, EXEMPLARY OR PUNITIVE DAMAGES, INCLUDING, WITHOUT
LIMITATION, ANY LOST PROFITS OR REVENUES, LOSS OR INACCURACY
OF ANY DATA OR COST OF SUBSTITUTE GOODS, REGARDLESS OF THE
THEORY OF LIABILITY (INCLUDING NEGLIGENCE) AND EVEN IF SUMMIT
ELECTRONICS LLC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES, SUMMIT ELECTRONICS LLC’S AGGREGATE LIABILITY TO
EN 12

CUSTOMER FOR ACTUAL DIRECT DAMAGES FOR ANY CAUSE WHATSO-
EVER SHALL BE LIMITED TO THE CUMULATIVE PRODUCT FEES PAID BY
THAT CUSTOMER FOR THE PRODUCT CAUSING THE DAMAGES, IF ANY.
This Warranty gives Customer specific rights, and Customer may also have
other rights that vary from jurisdiction to jurisdiction. To obtain Warranty
service, Customer must email SUMMIT ELECTRONICS LLC Technical Support
prior to making a Product return. Customer must include with Product return
the following items (failure to enclose any of these items may result in a delay
in the processing of your Warranty claim): (i) a dated sales receipt that indi-
cates the place of purchase, model number of Product, and amount paid; (ii) a
detailed description of Customer’s problem with Product; (iii) Customer’s full
name, phone number, and return address, and; (iv) a money order made out
to SUMMIT ELECTRONICS LLC Electronics Corporation to cover return ship-
ping charges to US destinations only, for the applicable dollar amount shown
for the Product in the table above. SUMMIT ELECTRONICS LLC will not make
return shipments to a P.O. Box. For shipping to international addresses, actual
freight will be charged to Customer. Return your Product freight-prepaid in its
original packaging, or packaging that affords an equal measure of protection.
Please allow 4 to 6 weeks for the processing of your claim (6 to 8 weeks from
November to February).
EN 13

ES 1
Instrucciones de seguridad importantes
Lea estas instrucciones, conserve estas instrucciones, preste atención a
todas las advertencias, siga todas las instrucciones.
1) Asegúrese de que el CAD-FMX500 esté montado en un lugar que no
bloquee la vista de la carretera.
2) No utilice este aparato cerca del agua.
3) Limpiar solo con un paño seco.
4) No bloquee las aberturas de ventilación. Haga la instalación conforme a
las instrucciones del fabricante.
5) No lo instale cerca de fuentes de calor como radiadores, rejillas de cale-
facción, estufas u otros aparatos (incluidos amplificadores) que produzcan
calor.
6) Proteja el cable de alimentación para que no se pise ni se pellizque,
asegúrese de que el cable de alimentación no se enrede con el gas o rompa
los vendedores ambulantes.
7) Utilice únicamente los aditamentos / accesorios especi fi cados por el
fabricante.
8) Desenchufe este aparato durante tormentas eléctricas o cuando no lo
utilice durante largos períodos de tiempo.
9) Refiera todo el servicio a personal de servicio calificado. Se requiere
servicio cuando el aparato se ha dañado de alguna manera, como el cable
de alimentación o el enchufe está dañado, se ha derramado líquido o han
caído objetos dentro del aparato, el aparato ha estado expuesto a la lluvia o
la humedad, no funciona normalmente , o se ha caído.

ES 2
AVISO DE LA FCC PARA LOS USUARIOS:
ID de la FCC: 2AMSOSTW001
Precaución: Los cambios o modi fi caciones no aprobados expresamente
por la Parte responsable del cumplimiento podrían anular la autoridad del
usuario para operar el equipo.
Nota: Este equipo ha sido probado y cumple con los límites para un dispos-
itivo digital de Clase B, de acuerdo con la parte 15 de las Reglas de la FCC.
Estos límites están diseñados para proporcionar una protección razonable
contra interferencias perjudiciales en una instalación residencial. Este equi-
po genera, usa y puede irradiar energía de radiofrecuencia y, si no se instala
y usa de acuerdo con las instrucciones, puede causar interferencia dañina
a las comunicaciones de radio; sin embargo, no hay garantía de que no
ocurrirá interferencia en una instalación en particular. Si este equipo causa
interferencia dañina a la recepción de radio o televisión, lo cual se puede
determinar apagando y encendiendo el equipo, se recomienda al usuario
que intente corregir la interferencia mediante uno o más de los siguientes:
- Reorientar o reubicar la antena receptora.
- Aumente la separación entre el equipo y el receptor.
- Conectar el equipo a una toma de corriente de un circuito diferente al que
está conectado el receptor.
-Consulte al distribuidor oa un técnico de radio / TV experimentado para
obtener ayuda.
El dispositivo cumple con la parte 15 de las reglas de la FCC. El funciona-
miento está sujeto a las dos condiciones siguientes: (1) este dispositivo no
puede causar interferencias dañinas y (2) este dispositivo debe aceptar
cualquier interferencia recibida, incluidas las interferencias que puedan
provocar un funcionamiento no deseado.

ES 3
Contenido de la caja
CAD-FMX500
Montaje de ventilación
Montaje en tablero
Manual de usuario
Cable AUX
Adaptador de corriente
USB para coche
Cable de carga

ES 4
Visión general
1. Pinza ajustable (lateral)
2. Ranura para tarjeta TF
3. Rueda FM
4. Botón multifuncional (Reproducir / Pausar; Colgar /
Responder; Asistente de voz de Siri / Google)
5. Mic
6. Puerto de carga tipo C 5V
7. Botón de liberación de la pinza
8. Pinza ajustable (lateral)
9. Puerto USB
10. Botón BASS
11. Botón de cambio de modo (BT, TF, USB)
12. Pantalla LED
13. Toma AUX OUT

ES 5
Montaje
1. Gire la tuerca de montaje en sentido antihorario para aflojar la abrazadera.
2. Inserte la perilla de bola con el clip y el botón de clip en la abrazadera de
la base del cargador y gire la tuerca en el sentido de las agujas del reloj para
apretar la perilla de bola.
3. Presione el botón Clip para abrir el clip y fijarlo en la ventana de venti-
lación de su automóvil. Puede girar la perilla de bola para ajustar el ángel
que desee para el soporte del teléfono.
1. Gire la tuerca de montaje en sentido antihorario para aflojar la abrazadera.
2. Inserte el soporte del tablero con ventosa en la abrazadera del soporte
del teléfono y gire la tuerca en el sentido de las agujas del reloj para apretar
la perilla de bola.
Botón de clip Tuerca de
montaje
Perilla de
bola
Abrazadera
Clip
Puede montar su CAD-FMX500 con cualquiera de estos métodos:
Método 1: montaje de ventilación
Método 2: montaje en tablero
4. Presione el botón Liberar en la parte superior derecha del soporte del
teléfono para desbloquear la pinza ajustable (lateral).
5. Coloque su teléfono en la plataforma de carga y ajuste las dos pinzas
ajustables (ambos lados) para bloquear su teléfono en su lugar.

ES 6
3. Retire la película protectora de la ventosa adhesiva en la parte inferior del
soporte del teléfono. Luego presione la ventosa en su tablero y empuje el
seguro hacia abajo para asegurarlo en su lugar. Ajuste el ángulo y la altura
del CAD-FMX500 para que no bloquee la vista de la carretera y apriete la
perilla para fijarlo en su lugar.
A la toma de corriente CC de
su automóvil
4. Press the Release button on the upper right of the phone mount to unlock
the adjustable gripper (side).
5. Place your phone onto the charging pad, and adjust the two adjustable
grippers (both sides) to lock your phone in place.
Encendiendo
Para encender este dispositivo, conecte un extremo del cable USB - Tipo C
suministrado al puerto Tipo C del CAD-FMX500 y el otro extremo al adap-
tador de corriente para automóvil suministrado. Enchufe el adaptador de
corriente para automóvil en la toma de corriente CC de su automóvil. Una
vez encendido, la palabra “HI” aparecerá en la pantalla LED. Luego, después
de 2 segundos, la palabra “bt” parpadeará en la pantalla de este dispositivo
para emparejarlo.
Bloqueo abierto
Cerradura
cerrada
Apriete la
perilla