Cartft CTFCAM-1 Series User guide

IP HD DOME CAMERA
QUICK OPERATION GUIDE

1. How to modify the IP address of PTZ
Current there is two method on modifying PTZ IP address: one via website;
another one via search tools.
Modify the PTZ IP address via IE website
1.1 set the computer network for connection testing
The PTZ camera default IP address is 192.168.1.18 ,so need to set the computer IP 1 address
in the same segment. Put the mouse on the computer desktop "network" icon,
press the right mouse button to click on the "properties" then you can open”the
network and sharing center”, then click “local connection”, click “properties” in the
pop-up dialog box (general),and then double-click the “Inter protocol version 4
(tcp/IPV4)”in the pop-up dialog box (Network). Last select "use the following IP
address” to configure a 0 segment of the IP.
0
1
0
3
0
2
0
6
0
5

1.2 IE login
Open the IE browser, in the tools / security / custom level (C)... make the"ActiveX
control and interpolation"all select "enable" or "tip", also make the security level to low.
01
02
02
03
Input the network PTZ IP address
(factory Default IP address:
192.168.1.18) then click”Enter”, which
will appear the browser landing interface.
In the login interface input the network
user name(default: admin) and pass
word(default: admin) then
click [log].

After the first time to enter the login
interface, it will appear”Click here to
download the plugin, please close the
browser when installation”tip as the follow
diagram,click to install the plugin. Last click
to download the controls : install and run
this controls once it was downloaded.
You can view the real time video by refreshing the website after the
installation finished.
1.3 modified IP
Then enter the settings - network -network, you can modify the PTZ IP address as
below picture:

Mark: you also can use ONVIF test tools(ONVIF Device Manager” to search the PTZ IP
address.

2. Operation method
2.1 Network PTZ camera connection
Network PTZ camera default IP address: 192.168.1.18, user name: admin, pass
word:admin;Normally working voltage under DC12V/4A±10% or POE, the
connection in LAN as below:
2.2 Search and add IP address
Network ptz camera fast access can use the search function in the support software.
Using search function automatically search the IP address of the network ptz camera
in the same LAN. Open the search tools, click search. Search out the IP, and then
point to modify the IP, and then modify the network information inside the device, for
example as following chart:
02
03

Mark: you also can use ONVIF test tools(ONVIF Device Manager” to search the PTZ IP
address.

3. Take NVR which support ONVIF to add devices
Take NVR which support ONVIF to add ptz, the main attention is the ONVIF port,
user name and password these three items are to be kept consistent. PTZ ONVIF
port can be seen on the IE Figure:
Mark: the IP address of the NVR and the PTZ camera should be in the same LAN.
4. Set the ptz camera preset
Take IE interface for example: after you enter into the zoom camera page in the IE
interface,click”PTZ control” on the left then will appear the direction key of controlling
ptz, Figure:Operate the ptz run to the location where you want to set preset, then
click the ptz function on the left, select the preset value you want to set, then click
set to finish. Figure:

5. Function commands
Function Control mode Remarks
The first cruising line (1st to 16th preset
points) Call the 41st preset point
The second cruising line (17st to 32nd
preset points) Call the 42nd preset point
The third cruising line (65th to 80th
preset points) Call the 43rd preset point
The fourth cruising line (113rd to 128th
preset points) Call the 44th preset point
The fifth cruising line (129th to 144th
preset points) Call the 45th preset point
The sixth cruising line (146th to 160th
preset points) Call the 46th preset point
The seventh cruising line (161st to
176th preset points) Call the 47th preset point
The eighth cruising line (177th to 192nd
preset points) Call the 48th preset point
Stay for 2 seconds at the cruising
preset point Set the 51st preset point
Stay for 4 seconds at the cruising
preset point Set the 52nd preset point
Stay for 6 seconds at the cruising
preset point Set the 53rd preset point
Stay for 8 seconds at the cruising
preset point Set the 54th preset point
Stay for 10 seconds at the cruising
preset point Set the 55th preset point
Enable the left-right limit scanning Call the 38th preset point
Disable the left-right limit scanning Set the 38th preset point
Set the left limit Set the 35th preset point
Set the right limit Set the 36th preset point
Set the scanning speed limit
Set the 61st, 62nd, 63rd and 64th preset points
corresponding to a scanning speed of 6°/s,
9°/s , 15°/s and 40°/s.
Default:
15°/s