CE Tech 5623-WH User manual

Flat Screen TV
Receiver
Receptacle
Concealed Wiring
(hidden in wall)
Flat Screen TV
Receiver Receptacle
Concealed Wiring
(hidden in wall)
Parts Included:
1. Pre-Assembled Top Plate w/ 15A / 125V duplex
receptacle and pre-stripped electrical building wire
2. Bottom Plate with easy push-in connectors
3. 6 ft. extension cord w/ 360º rotating flat head
Instruction/Installation Sheet
CE Tech No. 5623-WH Flat Panel TV Cable Organizer Kit
Tools Needed:
1. Drywall Saw
2. 6 ft. Tape Measure
3. Pencil
4. Phillips Head Screwdriver
Use the Flat Panel TV Cable Organizer Kit to install power and low voltage cables behind your flat panel TV, amplifier, or other
audio and video devices to your equipment, your equipment room or other location.
• Always follow local electrical code when installing this product.
• The electrical parts in this kit are designed to be used only as a kit and none of these electrical parts are designed to be used individually.
• This product is not designed to be part of your home or a commercial building’s electrical wiring system.
• This installation is only energized (electrically active) when the supplied 6 ft. cord is plugged into the recessed straight blade inlet (located
on the recessed low voltage cable plate) and the straight blade end of the 6 ft. cord is plugged into either your surge protector or wall receptacle.
IMPORTANT INSTRUCTIONS:
If you are not familiar with home wiring systems, please call a qualified electrician to install this product.
IMPORTANT INSTRUCTIONS:
This product is designed for retrofit work only because the electrical outlet box cannot be attached to a stud.
Installation Instructions for Retrofit Work Only:
Select the location of your flat panel TV mounting bracket. Next, select the location for both the top and bottom plates.
CAUTION: - Risk of Fire - Do not install Power Supply Cord within the Wall Cavity.
CAUTION: - Risk of Fire and Shock. No not connect this box to any other circuits or outlets.
Page 1 of 5 10/29/15
MADE IN CHINA
HECHO EN CHINA
DISTRIBUTED BY
DISTRIBUIDO POR
HOME DEPOT U.S.A., INC.
2455 PACES FERRY RD., N.W.
FOR ASSISTANCE, CALL:
SI NECESITA AYUDA,
LLAME AL:
1-800-394-7519
HOMEDEPOT.COM

Page 2 of 5 10/29/15
Installation / Instruction Sheet - No.5623-WH (Continued)
Top view - shows needed space between the drywall and the studs. The
power output plate should be centered between the studs.
Using the template supplied (see page 5 of instruction sheet), trace the opening for both the top and
bottom plate. See Figure 1 before tracing your opening. Remember, the plates are designed to be
mounted centered between the studs. Using a drywall saw, cut a hole in the drywall the size of each
template.
Run your low voltage cables and the included 14/2 with ground UL approved electrical building wire
(attached to the top plate) from the top opening in the wall through the bottom opening in the wall.
You will need to fish the cables from the top opening to the bottom opening. If you have more than 4
cables, you can remove the flexible plate that seals the low voltage cable opening using a pair of
needle nose pliers, thus allowing for more cables to be pulled through the opening.
Stop: Important: Before installing the top power plate into the top wall opening, make sure to pull
your low voltage cables through the low voltage cable opening at the back of the top plate.
After inserting your low voltage cables and the electrical building wire through the opening for the top
plate, insert the top plate into the wall by inserting the electrical work box into the wall first
(see Figure 4).
Slowly slide the top power plate into the opening. Swing the top of the plate into position until the
entire plate is flush against the wall.
Using a Phillips screwdriver, tighten the screws with wings. These wings fasten tightly against the
back of the wall. Note: Do not overtighten screws.
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
FOR ASSISTANCE, CALL:
SI NECESITA AYUDA,
LLAME AL:
1-800-394-7519
HOMEDEPOT.COM

Page 3 of 5 10/29/15
Installation / Instruction Sheet - 5623-WH (Continued)
Now that you have pulled the top power outlet plate’s electrical building wire though the bottom hole
in the wall, bend the wire straight. Then break any one of the four tabs in the back of the white old
work box. Now push the stripped end of the wire through the opening in the white old work box.
Insert the stripped end of the wires into the push-in connectors. First, insert the stripped black wire
into the open side of the push-in connector with the black wire – be sure to push the stripped black
wire completely into the connector. Now insert the stripped white wire into the open side of the
push-in connector with the white wire. Next, insert the bare copper ground wire into the open side
of the push-in connector with the green ground wire.
all of the wires and the push-in connectors into the white old work box.
Now screw the white old work box to the back of the bottom plate.
Figure 6
Figure 7
Figure 8
Figure 9
FOR ASSISTANCE, CALL:
SI NECESITA AYUDA,
LLAME AL:
1-800-394-7519
HOMEDEPOT.COM

Page 4 of 5 10/29/15
Installation / Instruction Sheet - 5623-WH (Continued)
WARNING:
• CE Tech’s products shall be installed and used only as indicated in CE Tech’s product instruction sheets.
• Instruction sheets are available online at www.datacommelectronics.com
• CAUTION: - Risk of Fire and Shock - Only intended for use on 15 ampere branch circuits.
CAUTION:
• For shock protection, this device must be properly grounded.
• Use copper wire only with this device.
IMPORTANT INSTRUCTIONS:
• Read and understand all instructions.
• Follow all warnings and instructions marked on the product.
• Do not use this product near water, for example; near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool.
• SAVE THESE INSTRUCTIONS
Now pull your low voltage cables through the cable opening in the bottom plate.
Stop: Important: Before installing the bottom recessed plate with inlet into the bottom template
opening, make sure to pull your low voltage cables through the low voltage cable opening in the
back of the plate.
After you have pulled your low voltage and audio/video cables through the bottom power input plate,
insert the side of the plate with the electrical work box into the wall first. (see Figure 10). Swing the
right side of the plate into position until the entire plate is flush against the wall. Now tighten the
screws with wings. These wings fasten tightly against the back of the wall. Note: Do not overtighten
screws.
Now hang your flat panel TV on the mounting bracket (not included) and plug your TV into the top
power output plate. Then plug your power cord set into the bottom power input plate. Complete
installation by plugging the male end of the power cord set into the nearby wall receptacle.
Figure 10
Figure 11
3026001
FOR ASSISTANCE, CALL:
SI NECESITA AYUDA,
LLAME AL:
1-800-394-7519
HOMEDEPOT.COM

Page 5 of 5 10/29/15
Installation / Instruction Sheet - 5623-WH (Continued)
TEMPLATE
ACTUAL SIZE

TEMPLATE
ACTUAL SIZE

3026001
FOR ASSISTANCE, CALL:
SI NECESITA AYUDA,
LLAME AL:
1-800-394-7519
HOMEDEPOT.COM