3B15484C※All specification is subject to change without notice to improve the quality.
SPECIFICATION
Type 1
Regulated 12V DC ±10%
Type 2
12V DC/24V AC Dual voltage
FUNCTION SETTING
1. How to use the jog lever
①ENTER :
② UP, ③ DOWN :
④LEFT, ⑤RIGHT :
⑥ FOCUS, ⑦ZOOM :
⑧ EXT. VIDEO :
Used to access the menu
and confirm selection.
Used to move the
cursor to up or down.
Used to move the
cursor to left or right and change
the value.
Use a '+' type
driver for adjusting zoom and focus.
(In case of operation Focus/Zoom,
don't put stress excessively.)
Extra video output
terminal for installation. The cable is
option.
*OSD menu & Focus/Zoom
adjustment direction
1. Unfasten the screw of the
bottom door
2. Adjust the jog lever & Focus
/Zoom trimmers
3. Tighten the screw of the
bottom door
F
EXT.VIDEO
Z
7
6
82
5
13
4
1/3" SONY SUPER HAD CCD
768(H) X 494(V) PIXEL(NTSC), 752(H) X 582(V) PIXEL(PAL)
6.35 (H) X 7.4 (V)(NTSC), 6.5 (H) X 6.25 (V)(PAL)
2:1 Interlace
Internal/ Line-Lock(option)
600 TV-LINE(COLOR), 700 TV-LINE(B/W)
52dB or More(AGC OFF)
1.0 Vp-p(Sync. Negative) Termination 75
γ= 0.45 typ.(0.45, 0.6, 1.0, user)
Yes(Multi Language)
ATW(2,500°K ~ 9,500°K)/MANUAL/AWC
1/60(1/50) ~ 1/100,000sec
Auto(Selectable limit 2X~256X)/FIXED/OFF
BLC, LWDR, DWDR, HLC(ON/OFF)
LOW/MIDDLE/HIGH/OFF
LOW/MIDDLE/HIGH/OFF
ON/OFF(240 Block)
ON/OFF(8 Zone)
H/V/BOTH
ON/OFF
AUTO, COLOR, B/W(Option : ICR)
40pcs, Dynamic IR
ON/OFF
ON(10X)/OFF
AUTO/OFF
RS-485(Protocol : Pelco D, Pelco P)
Vari-focal auto iris lens
Max. 850mA(at 12V DC, 24V AC) : LED ON
-10℃ ~ 50℃
-20℃ ~ 60℃
80.4(W) X 80.7(H) X 101.7(D)mm
Approx. 900g
Ⅱ
㎛ ㎛ ㎛ ㎛
Ω
0.01Lux(F/1.2), 0.0003Lux(Sense up),
0Lux(40M Range with 40pcs LED) - Indoor
Image Sensor
Effective Pixel
Cell Size
Scanning System
Sync. Type
Resolution
S/N
Video Output
OSD
Sense up
AGC
DNR(3D)
Gamma
White Balance
Shutter Speed
Backlight
Motion Detection
Privacy Zone
Mirror
Freeze
Day & Night
LED Brightness
DIS
Digital Zoom
Blemish Compensation
Communication(option)
Lens
Power Supply
Current Consumption
Operation Temp.
Preservation Temp.
Dimension
Weight
Min. Illumination
3. How to control through RS-485 communication(Option)
4. Cable array(Option)
1) Match the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right of Jog lever is same as Up, Down, Left and
right of RS-485 controller
3) Enter of Jog lever is thesame as menu key or IRIS open key of RS-485
controller
If the product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
Function
RX +
RX -
Remark
RS-485A
RS-485B
No.
A
B
A : ORANGE(RX +)
B : WHITE(RX -)
2. OSD menu structure
0~99
AUTO
OFF, LOW,
MIDDLE, HIGH
OFF,
X2~X256
OFF, ON
OFF, ON
0~20
0~60
0~70
0~100
3~12
OFF, ON
AUTO
0~60
OFF, ON
0~20
ATW
MANUAL
AWC↓
0~255
0~255
0~255
0~255
AUTO
COLOR
B&W
45~160
30~125
3~12
OFF, ON
OFF,
MODE1,
MODE2
OFF, VERT,
HORI, BOTH
0~49
OFF, ON
OFF, ON
0~50
OFF, ON
X1.0~X10
-128~127
-110~109
OFF, ON
Fixed focal lens or Vari-focal auto iris lens
Adjust the brightness
Shutter speed auto adjustable
Select shutter speed manually
Determines that use the AGC function or not
and AGC level selectable(You can not use the
Auto D&N change mode when AGC is off)
Using sense up when it is low luminance
(OFF, x2~x256 selectable)
When the Sense-up is activated and the camera
detects motion, operates LED and changes to
B/W mode if this mode is activated. Then user
can see vivid images without the afterimage.
(You can set this mode when the camera has
LED and the D&N mode is set to "Color".)
BLC function
Adjust BLC level
Select LWDR
Adjust WDR level
Using the Auto mode, set the WDR ON brightness
Using the Auto mode, set the WDR OFF brightness
Using the Auto mode, set the WDR switching
delay time
Digital Wide Dynamic Range
High Light Compensation(Using the Auto mode,
the HLC is not activated in day light.)
According to the threshold value, the camera
will recognize as High light or not.
Reduce noise in low illumination
Level is selectable
Color temperature 2500 ~ 9500°K
Adjust the Red or Blue values
Move the camera lens toward to white paper
then press the enter button to find the optimal
white balance for current environment
Adjust the Red value to shift the color ofthe object
Adjust the Blue value to shift the color ofthe object
Adjust Red tone of the image
Adjust Blue tone of the image
Auto day&night switching mode
Fixed at color(LED OFF)
Fixed at B/W(LED level selectable)
Select brightness of illumination about changing
the day ↔ night mode
Select the duration time about changing the
day ↔ night mode
Determines whether to transmit the burst signal
or not in B/W mode
When IR LED is turned on in B/W, the objects
can be clearly identified due to the function
that decreases screen saturation of objects
within a short distance.
VERT : Set a vertical image inversion
HORI : Set a horizontal image inversion
BOTH : set a image rotation
Sharpness adjustable
Gamma adjustable
Get a still image
Determines whether to use the brightness
compensation of four lens' corners(LSC) or not
The LSC level selectable
Max 10x digital zoom available(Default value is X3)
Digital zoom adjustable
Zoomed in image can be moved to horizontal
Zoomed in image can be moved to vertical
This function can be mitigates image movement
from external factors(This function uses digital
zoom)
LENS
LEVEL
E.SHUTTER
AGC
SENSE UP
ANTI-
GHOST
BLC
LEVEL
LWDR
LEVEL
OFF→ON
ON→OFF
DELAY TIME
DWDR
HLC
LEVEL
DNR
LEVEL
WB MODE
R-Y GAIN
B-Y GAIN
D&N MODE
DELAY TIME
BURST
DYNAMIC IR
FLIP
SHARPNESS
GAMMA
FREEZE
LSC
LEVEL
DZOOM
ZOOM
PAN
TILT
DIS
Function
setting menu Select menu ContentsSub menu
MANUAL , DC
1/60(1/50)~1/100,000
MANUAL B LUE
MANUAL RED
BW COLOR→
COLOR BW→
0.45, 0.6, 1, USER
1. EXPOSURE
3. DAY&NIGHT
4. IMAGE ADJ.
2. WHITE
BALANCE
PATTERN
GENERATOR
Test signal. Press the enter button, color bar appeared on the
screen and press any key to return to menu.
Determines whether to use the motion detection
function or not
No display on the screen though movement is
detected
The words 'MOTION' appear on the screen when
movement is detected
Motion detection sensitivity
Set the duration of alarm out. If the way of display
is message, it means display time of message
Not available
Display each privacy mask or not
Select mask color(8 color is available)
Select language
Display the camera ID on the screen
Defect pixel correction in low illumination
Setup the limited value of white pixel correction
Setup the limited value of black pixel correction
Setup the DPC(Defect Pixel Correction) level
Internal Sync with 12V DC power
Setting the phase is selectable when used
24V AC(Dual power only)
Phase contollable at 24V AC input(L/L mode)
Monitor setting
Select the camera ID for RS-485 communication
Select baud rate
Select protocol
OFF, ON
NONE
MESSAGE
0~120
1~15
OFF
OFF, ON
BLACK, GRAY…
ENGLISH, …
OFF, ON
OFF, AUTO
0~255
0~255
0~255
INT
L/L
0~255
CRT, LCD
1~255
MOTION
DISPLAY
SET
WINDOW
ALL SET↓
SENSITIVITY
HOLD TIME
IMPACT
MASK 1 ~8
SET
WINDOW
COLOR SET
LANGUAGE
TITLE
EDIT
RESET↓
POSITION
DPC
WHITE THR
BLACK THR
DPC LEVEL
SYNC
VPHASE
MONITOR
COM. ID
BAUDRATE
PROTOCOL
FACTORY
SET↓
EXIT↓
RETURN
7. SPECIAL
6.PRIVACY
ZONE
8. EXIT
2400, 4800, 9600
PELCO-D, PELCO-P
COMMUNICATION
SAVE AND EXIT↓
ALL CLEAR↓
5. ALARM
Press the enter button to move into the motion detection area section
to set the 240 blocks. To escape this menu, you should press the left
button at the far left or press the right button at the far right.
Press the enter button to select all area
Press the set button to remove all area
Press the enter button at first time, you can move the mask's
position. After press the enter button again, you can adjust the
size of mask. If you press the set button once more, you can
adjust position of edge. After decided position of edge then
press the enter button, it will be back to previous menu.
Camera ID setting
Camera ID reset
Camera ID position
Communication setting(option)
Reset your camera to factory default condition and then restart
Notice : Lens, communication and language is not changed
Save the value and then restart
Escape the menu without save
Move back to previous menu
ㆍThe ' ' icon appeared with desired function, press the set button to move sub menu.
ㆍThe '- - -' icon appeared with function that is unavailable according to function setting.
OFF, LOW, MIDDLE, HIGH
OFF, ON , AUTO
