Certa POWERPLUS CT20VLNTRMA User manual

20V POWERPLUS
LINE TRIMMER
(SKIN ONLY)
CT20VLNTRMA

Read these instructions in full before use. Retain this user guide for future reference.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious
injury.
General Safety Instructions
WARNING! Read all safety warnings and all instructions.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your corded power tool or battery pack-
operated power tool.
•This product is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge unless
they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety.
•Only use the product in the manner and for the functions described in these
instructions.
Work Area Safety
•Keep work area clean and well lit. Cluttered or dark areas create higher risk for
accident.
•Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
•Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
Electrical Safety
•Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with grounded power tools. Unmodified plugs and matching
outlets will reduce the risk of electric shock.
•Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
•Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
•When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
SAFETY & WARNINGS

•If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent to avoid a hazard. Cease use and contact help.kogan.com before
further use.
•It is recommended that appliances should be supplied via a residual current device
(RCD) with a tripping current of not more than 30mA.
Personal Safety
•Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
alcohol, drugs, or medication. A momentary lapse of attention while operating
power tools may result in serious personal injury.
•Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce personal injuries.
•Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to a power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that
have the switch on invites accidents.
•Remove any adjusting key or wrench before turning the power tool on. A wrench or
a key left attached to a rotating part of the power tool may result in personal injury.
•Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
•Dress appropriately. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
Power Tool Use and Care
•Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was
designed.
•Do not use the power tool if the switch does not turn it on and off. Any power tool
that cannot be controlled with the switch is dangerous and must be repaired
•Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories or storing
power tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally.
•Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
•Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.

•Keep cutting parts sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
•Use the power tool, accessories and tool bits etc. by these instructions, taking into
account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous
situation.
Cordless Line Trimmer Safety Warnings
•Keep all parts of the body away from the cutting blade. Do not remove cut
material or hold material to be cut when blades are moving. Make sure the
product is switched off when clearing jammed material. A moment of inattention
while operating the product may result in serious personal injury.
•Carry the product by the handle with the cutter blade stopped. When
transporting or storing the product always fit the cutting device cover. Proper
handling of the product will reduce possible personal injury from the cutter blades.
•Hold the product by insulated gripping surfaces only, because the cutter blade
may contact hidden wiring or its own cord. Cutter blades contacting a “live” wire
may make exposed metal parts of the product “live” and could give the operator an
electric shock.
•Check the hedge for foreign objects before the operation, e.g. wire fences.
•Hold the product properly (e.g. with both hands). Loss of control can cause
personal injury.
Additional Safety Warnings
Important: Read carefully before use. Keep for future reference
Training
•Read the instructions carefully. Be familiar with the controls and the proper use of
the appliance.
•Never allow children to use the product.
•Never allow people unfamiliar with these instructions to use the appliance. Local
regulations may restrict the age of the operator.
•Never operate the appliance while people, especially children or pets are nearby.
•The operator or user is responsible for accidents or hazards occurring to other
people or their property.

Preparation
•Wear eye and ear protection (safety goggles and ear muffs) while operating.
•Always wear substantial footwear and long trousers. Do not operate the equipment
when barefoot or wearing open shoes.
•Always wear suitable working clothes while operating, which allow freedom of
movement.
•Never operate the appliance if it is damaged, incomplete or modified without
approval of the manufacturer.
Operation
•Disconnect the battery from the product:
owhenever you leave the product,
obefore clearing a blockage,
obefore checking, cleaning or working on the product,
oif the product starts to vibrate abnormally.
•Operate the product only in daylight or in good artificial light.
•Do not overreach; keep your balance at all times.
•Always be sure of your footing on slopes.
•Walk, never run.
•Keep all ventilation openings clear of debris.
•Never blow debris in the direction of bystanders.
Maintenance and Storage
•Keep all nuts, bolts and screws tight to be sure the product is in safe working
condition.
•Replace worn or damaged parts.
•Store the product only in a dry place.
Residual Risks
Even if you are operating this product by the provisions, residual risks will always remain. The
following dangers can arise in connection with the structure and design of this product:
•Health defects resulting from vibration emission if the product is being used over a
longer period or not adequately managed and properly maintained.
•Injuries and damage to property due to broken accessories or hidden objects that
are thrown in the process of using the Line Trimmer.
•Injuries and damage to property due to thrown and fallen objects.

WARNING! This product produces an electromagnetic field during operation! This field may
under some circumstances interfere with active or passive medical implants! To reduce the
risk of serious or fatal injury, it recommends persons with medical implants to consult their
physician and the medical implant manufacturer before operating this product!
Vibration and Noise Reduction
To reduce the impact of noise and vibration emission, limit the time of operation, use low-
vibration and low-noise operating modes as well as wear personal protective equipment.
Emergency
Familiarise yourself with the use of this product using this instruction manual. Memorise the
safety directions and follow them at all times. This will help to prevent risks and hazards.
•Always be alert when using this product, so that you can recognise and handle
risks early. Fast intervention can prevent serious injury and damage to property.
•Stop the motor and disconnect the battery from the product if there is any
malfunction. Have the product checked by a qualified professional and repaired, if
necessary, before you put it into operation again.
Safety Warnings and Instructions when using with battery pack (not supplied)
•Do not disassemble or open, drop (mechanical abuse), crush, bend or deform,
puncture, or shred.
•Do not modify or remanufacture, attempt to insert foreign objects into the battery,
immerse or expose to water or other liquids, or expose to fire, excessive heat
including soldering irons, or put in microwave oven.
•Only use the battery/tool with a charging system specified by the
manufacturer/supplier.
•Do not short-circuit a battery or allow metallic or conductive objects to contact
both battery terminals simultaneously.
•Dispose of used batteries promptly according to the manufacturer/supplier’s
instructions.
•Improper battery/tool use may result in a fire, explosion, or other hazard.
•Battery/tool usage by children should be supervised.
Safety Warnings and Instructions for when using with charger (not supplied)
•This manual contains important safety and operating instructions.
•Before using battery charger, read all instructions and cautionary warnings on
battery charger and product using battery. CAUTION: To reduce the risk of injury,
use this charger only with this product. Batteries in other products may burst
causing personal injury or damage.
•Do not expose charger to rain or snow.

•Use of an attachment not recommended may result in a risk of fire, electric shock,
or injury to persons.
•To reduce risk of damage to electric plug and cord, pull by plug rather than cord
when disconnecting charger.
•Make sure cord is located so that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
•An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.
•An extension cord must have adequate wire size (AWG or American Wire Gauge)
for safety, and to prevent loss of power and overheating. The smaller the gauge
number of the wire, the greater the capacity of the cable; that is, 16 gauge has
more capacity than 18 gauge. When using more than one extension to make up
the total length, be sure each extension contains at least the minimum wire size.
Chart for Minimum Wire Size (AWG) Of Extension Cords
Nameplate Rating AMPS – 0 – 10.0
Total Extension
Cord Length (ft)
0-25
(0-7.6m)
26-50
(7.6-15.2m)
51-100
(15.2-30.4m)
101-150
(30.4-45.7m)
Wire Gauge
18
16
16
14
•Use only the supplied charger when charging your tool. The use of any other
charger could damage the tool or create a hazardous condition.
•Use only one charger when charging.
•Do not attempt to open the charger. There are no customer serviceable parts
inside.
•DO NOT incinerate the tool or batteries even if they are severely damaged or
completely worn out. The batteries can explode in a fire. Toxic fumes and materials
are created when lithium ion battery packs are burned.
•Do not charge or use battery in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting or removing the battery from the charger
may ignite the dust or fumes.
•If battery contents come into contact with the skin, immediately wash area with
mild soap and water. If battery liquid gets into the eye, rinse water over the open
eye for three minutes or until irritation ceases. If medical attention is needed, the
battery electrolyte is composed of a mixture of liquid organic carbonates and
lithium salts.
WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

Symbols in this guide and on the line trimmer:
Warning, safety alert.
Read and follow all safety precautions in the owner’s manual.
Protective goggles/visor, protective helmet & hearing protection.
Do not expose to rain.
Beware of thrown or flying objects to bystanders. Keep bystanders a
safe distance away from the machine.
Thrown objects can ricochet and result in personal injury or property
damage. Wear protective clothing and boots.
Beware of falling objects. Keep bystanders away.

1
Unlock knob
9
Telescopic pole
2
Switch handle
10
Lock sleeve and edging function button
3
Main handle
11
Angle adjustment handle
4
Battery pack
12
Trimmer head
5
Auxiliary handle
13
Nylon line
6
Handle lock nut
14
Angle adjustment button
7
Handle support
15
Edging function wheel
8
Locking sleeve
(length adjustment)
16 Safety guard
OVERVIEW

Warning!
If equipped with a battery pack, ensure it is removed before cleaning or maintaining the tool,
fitting the plant guard before making any adjustments to the tool, especially around the
string head. Remove battery pack before transporting or storing the tool.
Install the Line and Operate
Place the wider eyelet of the cutting blade over the metal stud and firmly pull until the blade
is completely seeded on the stud. To remove, repeat these steps in the opposite order.
ASSEMBLY
1
2
4
6
5
3

Fitting the Guard
The guard is an essential part of the tool and must always be
used. Otherwise, damage to the trimmer and injury to the
operator may occur. The guard is not fitted to the trimmer when
it is delivered to you to avoid damage in transit.
Align the guard with the trimmer head as shown,
Adjusting Auxiliary Handle
The auxiliary handle is height and angle adjustable. To adjust
the handle, press on the button on both sides of the handle at
the same time. Rotate the auxiliary handle to the desired
position and slide the handle support to the desired height,
clamp in position.
Setting the Trimmer Head Angle
The angle of the trimmer head can be set to different working positions.
Press the angle adjustment button with one hand and rotate the trimmer head to the
required position. Release the button and the head will lock into place.
There are 3 preset lock positions:
Setting the Handle Length
Turn the lock sleeve (8) towards the ‘unlock’ symbol about half a
turn. Slide the lower part of the trimmer up or down to the desired
length. Lock it in position by turning the lock sleeve towards the ‘lock’
symbol.
Unlock

WARNING: Before operating this tool, ensure that the guard is fitted to the head of the
machine. Never use the machine without the guard.
Starting/Stopping the Trimmer:
To switch the trimmer on, first, push forward the unlock knob (1) then hold the switch handle
(2), the trimmer is now running. You can release the unlock knob.
To switch the trimmer off, release the switch handle. Be aware that the blade will continue
to rotate for a short period.
OPERATION

Trimming Mode
There are 2 working positions, for normal trimming and for edging.
To use the trimmer in edging mode, use the edging function button (10) to rotate the lower
part of the trimmer 90° until the button aligns with the angle adjustment handle (11).
Release, the locking knob. Then set the trimmer head angle as shown in edging mode
images.
Edging
Trimming
Edging
Trimming

•Disconnect the battery pack from the machine before carrying out maintenance or
cleaning work.
•When not in use store the machine out of the reach of children.
•To clean the tool, remove the battery pack and use only mild soap and a damp
cloth to clean the tool. Do not immerse tool in water or spray with a hose. Do not
allow any liquid to get inside it. Do not clean with a pressure washer.
•Inspect and maintain the machine regularly. Has the machine repaired only by an
authorised repairer.
•The battery must be removed from the appliance before it is scrapped.
•The appliance must be disconnected from the supply mains when removing the
battery.
•The battery is to be disposed of safely.
Rated Voltage
20V DC
No Load Speed
8500rpm
Cutting Device
Nylon line
Cutting Swath Diameter
250mm
Guaranteed sound power level
92 dB(A)
Battery Pack (not supplied)
Lithium Ion – 1500mA
Full weight (when fitted with battery
pack)
2.0kg
These instructions should be read in conjunction with the instruction manual for the
battery pack and charger.
CLEANING & CARE
SPECIFICATIONS

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com