Champ Craft Boredom Buster 4280 User manual
Assembly Instructions
#4280 Boredom Buster
Tools Required for Installaon
Installaon Tips
Parts Idencaon
#2-
#12-
#8-
#10-
#14-
#11-
#15-
#1-
#3-
#4-
#5
#6-
#7-
#13-
#16-
#24-
Parts Idencaon
#20
#18
#22-
#17-
#19-
#21-
#23-
#25-
#26-
#27—
Parts Idencaon
2 ¼” Screw -
Swing Hanger -
1 ⅛” Screw- 1½” Screw-
1” Pan Head Screw-
Angle Iron -
¼” Lock Nut- Washer-
1½” Bolt-
Parts Idencaon
(Note: In this step you will make two Canopy Trusses. 1 right and 1 le)
Assemble the first Canopy Truss as pictured below. With 8 - 1” Screws (2 in
each board end) per truss.
-
Assemble the second Canopy Truss as pictured below. With 8 - 1” screws (2 in
each board end) per truss.
Flip each truss over and fasten part #23 in the peak of the truss with 4 - 1”
screws per peak.
Begin assembling Section #1.
-
-
Top
Boom
-
-
Secon #1
-
Finish section #1.
Fasten part #4 in the center, as pictured, with 4 - 1” screws.
Pre - drill with a 5/32” drill bit.
Secon #1
Attach the first Truss to Section #1.
Fasten Truss with 2” screws. Two screws 6” from post on left (short) side and 2
screws 20” from post on right (long) side.
-
Secon #1
-
Assemble Section #2
-
Secon #2
-
Top
Boom
-
-
-
Attach the second Truss to Section #2.
Fasten Truss with 2” screws. Two screws 20” from post on left (long) side and 2
screws 6” from post on right (short) side.
Secon #2
-
Fasten seven part #4’s to Section #2. Space 3” between each piece and fasten
with 4 - 1” screws per board.
Pre - drill with a 5/32” drill bit.
-
Secon #2
Stand up Section #2 and fasten part #10 using 2 - 2” screws
-
-
Fasten part #3 to Section #2 with 2 - 2” screws. Position the end of part #3 19”
from the outside edge of section #2 as shown.
-
-
Stand up Section #1 and fasten as shown with 4 - 2” screws.
-
-
Fasten one part #2 with 4 - 2” screws (2 at each end) between Section #1 and
Section #2.
Fasten one part #2 with 4 - 2” screws (2 at each end) between Section #1 and
Section #2.
On opposite side.
-
Assemble the oor frame.
-
Fasten one part #2 with 4 - 2” screws between Section #1 and Section #2. In
the center of the Floor Frame.
-
Fasten part #2 to the side of Section #1 and Section #2, 62” from the floor with
4 - 2” screws, as shown.
-
-
Lay the Floor Boards (two part #11’s and seven part #10’s) on the Floor Frame.
Space them evenly as pictured. Fasten with 6 - 1” screws per board. Pre - drill
with a 5/32” drill bit.
Fasten two part #2’s as pictured with 4 - 2” screws per board.
-
Table of contents
Popular Play Set & Playground Equipment manuals by other brands
TP Toys
TP Toys Active fun EARLY FUN TP069 Instructions for assembly maintenance and use
LifeSpan Kids
LifeSpan Kids Captain Sand Pit instructions
PLAYSTAR
PLAYSTAR Mesa PS 7460 Safety Guide & Assembly Instructions
Safespaces
Safespaces Safespace Assembly instructions
Lifetime
Lifetime 72005 Assembly instructions and owner's manual
BOERPLAY
BOERPLAY Playhouse with hill slide H1.95 manual