CHIEF MSP-DCCGPM-210 User manual

CHIEF MANUFACTURING INC. 8832-000080 (Rev. A)
1-800-582-6480 952-894-6280 FAX [phone] Chief Manufacturing
8401 EAGLE CREEK PARKWAY, STE. 700 www.chiefmfg.com
SAVAGE, MINNESOTA 55378 USA 04/05
INSTALLATION INSTRUCTIONS
Flat Panel
Tilt Wall Mount
MSP-DCCGPM-210
BEFORE YOU BEGIN
• CAUTION: To prevent damage to your display, which could affect or void the Factory warranty,
thoroughly study all instructions and illustrations before you begin to install the mount brackets. Pay
particular attention to the “Important Warnings and Cautions” on Page 2.
• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.
• If a defect is discovered after Dell’s initial 21-day Customer Satisfaction period, Chief Mfg. will, at its option, repair
or repair the product at not charge provided it is returned during the warranty period. Please note contact
information for Chief Mfg. listed below.
The tilt wall mount fits most 23” to 30” displays.
The mount is designed to adapt to VESA® 200mm/100mm
compliant displays. This mount will also adapt to standard
VESA® 75mm/100mm compliant displays.
The mount allows the user to adjust the viewing angle of the
mount + 15 degrees hand. The maximum load capacity of the
mount is 45 lbs. (20.4kg).
After adjusting the display to the desired angle, the user can lock
the mount into a fixed position. The user can easily remove the
display from the wall bracket when the mount is unlocked. MSP-DCCGPM-210

Installation Instructions MSP-DCCGPM-210
2
IMPORTANT WARNINGS and CAUTIONS!
WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow
the instructions.
CAUTION ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not
follow the corresponding instructions.
WARNING Improper installation can result in serious personal injury! Make sure that the
mounting surface can support a redundant weight factor five times the total weight of
the equipment: if not, reinforce the mounting surface structural members before
installing the mount.
WARNING Be aware of the potential for personal injury or damage to the unit if it is not
adequately mounted.
WARNING The installer is responsible for verifying that the mounting surface to which the
mount is anchored will safely support the combined load of all attached components
or other equipment.
WARNING The combined weight of the display placed on the mount must not exceed 45 lbs.
(20.4kg), the maximum load capacity of the mount.
WARNING Watch for pinch points. Do not put your fingers between movable parts.
WARNING Make sure the mount is correctly oriented.
CAUTION Check the unit for shipping damage before you begin the installation.
CAUTION If your monitor uses a longer screw size other than those included in the kit, DO NOT use
the screws provided with the mount. Use the screws provided with your monitor or contact
the manufacturer. Using the wrong screws could result in damage to your monitor.
CONTENTS
TILT MOUNT KIT ...........................................................3
Installing the Wall Bracket (Step 1) ............................4
OPTION A (Drywall Installation Procedures)..........4
OPTION B (Wall Stud Installation Procedures) ......5
Attaching the VESA Bracket to the Display (Step 2) ..6
Flushed Mount ........................................................6
Recessed Mount .....................................................7
Mounting the Display on the Wall Bracket (Step 3)....8
Locking the Display on the Wall Bracket (Step 4) ......8
TOOLS REQUIRED FOR
INSTALLATION
• Phillips screwdriver
• Drill and drill bits
NOTE: Other tools may be required depending
on your method of installation.

Installation Instructions MSP-DCCGPM-210
3
TILT MOUNT KIT
Unpack the carton. Verify the kit contents shown in Table 1. Read installation instructions completely. If you are
missing any of the listed components, please contact Customer Service at 1-800/582-6480.
Table 1. GPM-210 Tilt Mount Kit
ITEM
NUMBER DESCRIPTION QTY NOTES
10 BRKT, VESA TILT INTERFACE 1
20 BRKT, WALL TILT MOUNT 1
30 ANCHOR, HOLLOW WALL 6
DRYWALL
MOUNTED
40 PHILLIPS HEAD WOOD SCREW, 2-1/2” 2 SINGLE STUD
MOUNTED
50 NYLON WASHER 2
60 PHILLIPS PAN HEAD MACHINE SCREW, M5 X 10MM 2
TILT
ADJUSTMENT
70 PHILLIPS PAN HEAD MACHINE SCREW, M4 X 12MM 6 FLUSH MOUNT
80 PHILLIPS PAN HEAD MACHINE SCREW, M4 X 20MM
(USE WITH 90 OR 120) *
6
90 3/8” NYLON SPACER 6
100 PHILLIPS PAN HEAD MACHINE SCREW, M4 X 30MM
(USE WITH 110) **
6
110 3/4” NYLON SPACER 6
120 1/8” NYLON SPACER (USE WITH 90) *** 6
RECESSED
MOUNT
• *Use M4 x 20mm screws (80) with spacers (90) for recessed mount applications.
• **Use M4 x 30mm screws (100) with spacers (110) for recessed mount applications.
• ***Use M4 x 20mm screws (80) with spacers (120) for recessed mount applications.
100mm x 100mm
200mm x 100mm
75mm x 75mm
VESA CHART
VESA HOLE
PATTERN 4-HOLE 6-HOLE
FLUSH
MOUNT
RECESSED
MOUNT
75MM X 75MM X X X
100MM X 100MM X X X
200MM X 100MM X X X

Installation Instructions MSP-DCCGPM-210
4
Figure 1. Installing Wall Bracket — Drywall
%%c0.375 (PREDRILL HOLE)
INSERT ANCHOR INTOPPREDRILLED HOLE
CW
ANCHOR BARBP(STOPS ANCHOR ROTATION)
Figure 2. Anchor Installation
NOTE: Read the “Warnings and Cautions” on Page 2.
Installing the Wall Bracket (Step 1)
To install the wall bracket, perform Option A or Option B as
applicable.
OPTION A (Drywall Installation Procedures)
A. Determine the exact mounting location prior to
installation, considering screen size as well as the mount
tilt radius.
B. Position the wall bracket (20) as desired.
C. Using the wall bracket (20) as a template at the desired
mounting location, mark the location of the four corner
mounting holes and two center holes (see Figure 1).
NOTE: This procedure applies to a minimum drywall thickness
of ½ inch (12.7 mm).
NOTE: Mark the pilot holes as accurately as possible before
drilling the holes. The holes must be centered for the
wall bracket to fit correctly on the wall.
D. Using a 3/8-inch drill, drill six pilot holes at the locations
marked in Step 1, Option A.
E. Install an anchor (30) in one of the pilot holes and tighten
anchor bolt until it is fully seated (see Figure 2).
F. Remove and retain bolt from anchor (30) and repeat
Step E and F for five remaining anchors (30).
G. Using six bolts, with washers installed, secure wall
bracket (20) to wall.
Step 1, Option A
Center
Mounting
Holes
Corner
Mounting
Holes
Corner
Mounting
Holes
Mounting
Hole
Insert anchor into
p
redrilled hole.
Turn 10-24 screw
clockwise until
anchor fully seats
against back side
of wall.
#10-24
Scre
w
0.375
(pre-drill
hole)
A
nchor
(
30
)
A
nchor Barb
(Stops anchor
rotation)
CW

Installation Instructions MSP-DCCGPM-210
5
Figure 3. Installing Wall Bracket — Wall Stud
NOTE: Read the “Warnings and Cautions” on Page 2.
OPTION B (Wall Stud Installation Procedures)
A. Determine the exact mounting location prior to
installation, considering screen size as well as the mount
swing and extension radius.
B. Position the wall bracket (20) as desired (see Figure 3).
NOTE: Mark the mounting holes as accurately as possible
before drilling the holes. The holes must be centered for
the wall bracket to fit correctly on the wall.
C. Locate stud and, using wall bracket (20) as a template at
the desired height, mark the location of the two center
mounting holes.
D. Using the two wood screws (40), secure wall bracket
(20) to wall.
Step 1, Option B
Center
Mounting
Holes
Mounting
Hole

Installation Instructions MSP-DCCGPM-210
6
Figure 4. Flush Mount
Attaching the VESA Bracket to the Display
(Step 2)
NOTE: Choose the instructions, listed below, that apply to the
type of installation you want.
• Flush Mount Applications do not use spacers. The
display is attached to the mount with six screws.
• Recessed Mount Applications use spacers. The
display is attached to the mount with six screws and
four spacers. For the procedure, refer to page 7.
CAUTION: If monitor uses a screw size other than those
included in the kit, DO NOT use the screws
provided. Using the wrong screws could result in
damage to your monitor.
Flushed Mount
A. Place the VESA bracket (10) on the display
(see Figure 4).
B. Align the hole-pattern of your display with the hole-
pattern on the VESA bracket (10).
C. Attach VESA bracket (10) to the display using six
M4 X 10mm screws (70) provided.
Step 2
10
70

Installation Instructions MSP-DCCGPM-210
7
Figure 5. Recessed Mount
Recessed Mount
NOTE: Select option 1, 2, or 3 to pick the applicable screw and
spacer combination.
• Refer to Table 2 for 200mm/100mm compliant
displays.
• Refer to Table 3 for 75mm/100mm compliant
displays.
A. Select six screws and six spacers.
B. Set six spacers over the four mounting holes on your
monitor (see Figure 5).
C. Set VESA interface bracket (10) on top of spacers and
install six screws into the mounting holes of your display.
Table 2. 200mm/100mm Compliant Displays
OPTION SCREW QTY SPACER QTY
1 80 6 90 6
2 100 6 110 6
3 80 6 120 6
Table 3. 75mm/100mm Compliant Displays
OPTION SCREW QTY SPACER QTY
1 80 4 90 4
2 100 4 110 4
3 80 4 120 4
6
Screws
6
Spacers
NOTE:
For additional
information,
see VESA
Chart, page 3

Installation Instructions MSP-DCCGPM-210
8
Figure 6. Assemble the Brackets
Figure 7. Install the M5 Screw
Mounting the Display on the Wall Bracket
(Step 3)
A. With an assistant (if necessary), lift the display up to the
wall bracket (20) over the four mounting pins
(see Figure 6.
B. Align the mounting pins on the display with the slots in
the wall bracket (20), and set the display into place.
C. Verify that the display tilts on the wall bracket (20).
Locking the Display on the Wall Bracket
(Step 4)
A. Assemble a washer (50) over each M5 screw (60).
Install the two M5 (60) screw assemblies into the tapped
holes located on the side of the wall bracket (20).
See Figure 7.
B. Set the display into the desired position. Tighten the M5
screw (60) until friction holds the display stationary.
Step 3 20
Tapped
Hole
60
50
Step 4