Chord Blu MkII Instruction manual

Connecting BLU MKII to DAVE 3.0
Connect BLU MKII to DAVE via dual data mode. You can use either
BNC 1 and 2 or BNC 3 and 4. Navigate forward (not backwards) to
BNC 1 if outputs from BLU MKII are connected to BNC inputs 1 and 2
on DAVE, or navigate to BNC 3 if outputs from BLU MKII are connected
to BNC inputs 3 and 4.
Chord Electronics
BLU MKII | Quickstart Manual
The Pumphouse, Farleigh Lane, East Farleigh, Kent, ME16 9NB, United Kingdom
[e-mail]
chordelectronics.co.uk
Quickstart Manual
Introduction 1.0
Welcome to the BLU MKII Quickstart Guide. This shortened guide is
supplementary to the main manual which should be referred to for full
safety and operational information.
Please note, more information on any of these topics is listed within
the full manual.
Warranty 1.1
The BLU MK II comes with a comprehensive 5-year warranty. To
activate this warranty, please register your device via the Chord
Electronics website:
chordelectronics.co.uk/register-product
For more in-depth information on the safety and warranty of the BLU MKII
please see the full manual.
Connecting BLU MKII to a source 2.0
In order to use your BLU MKII as an upscaler/upsampler, you must
connect your source to any input of BLU MK II. You can connect up
to 2 devices. If you are using a MAC/Linux device you will not need
a driver but a Windows device will need a driver from the BLU MKII
section of our website:
chordelectronics.co.uk/product/blu-mk-2/
Input
Input
Connecting BLU MKII to third-party DACs 4.0
Use the Dual BNC, single BNC or AES outputs to connect your BLU
MKII with a third-party DAC. Dual BNC will only fuction with the 2
further right hand side BNC ports. The bottom left BNC port can not
be used as a Dual BNC connector.
For single BNC connectors use any of the 3 BNC outputs shown below
in Blue. The top left hand side BNC port is only to be used for an input
into the BLU MKII.
OR
Output

Chord Electronics
BLU MKII | Quickstart Manual
The Pumphouse, Farleigh Lane, East Farleigh, Kent, ME16 9NB, United Kingdom
[e-mail]
chordelectronics.co.uk
Quickstart Manual
For more in-depth information on the functions of the BLU MKII please
see the full manual.
Connecting BLU MKII to power 6.0
Connect the supplied mains IEC cable to the input of BLU MKII. Once
connected to the BLU MKII, it may start automatically. Please make
sure none of your other devices are switched on at this point.
Opening the CD mechanism 8.0
Now that you have successfully completed the setup of your BLU MKII
you can immediately begin to experience its transformational quality
on your digital music collection. However, we advise that you register
your product with us. Registering helps us give you the best possible
support and protects your investment:
Product registration 10.0
chordelectronics.co.uk/register-product/
Display and basic operation 9.0
Powering up BLU MKII 7.0
During use, you may need to navigate DAVE’s menu, this is simple. To
scroll through the menu use the left and right buttons. To navigate
through the sub-menu options (and set your selection) use the up and
down buttons. Once you have landed on an appropriate option you do
not need to confirm a selection it will be automatically applied. Use
the volume control to turn the volume up and down as appropriate. All
settings will be remembered when the device is switched o.
With BLU MKII you are able to choose which upsample rate is best
fitted for your system. On the back of BLU MKII are 2 switches, one is
the sample rate switch and the other the dither switch. In this section
we will talk about the sample rate switch on the left hand side of BLU
MKII. See the table below for switch positions.
For use with the DAVE we recommend using high upsampling to get
the best out of your experience. For third-party DACs, refer to their
manual to select the best rate suited.
Setting the upsampling qualities 5.0
POSITION - UP: Upsampling Low
eg. original signal 44.1kHz
POSITION - MID: Upsampling Medium
eg. signal now 176k.4kHz
POSITION DOWN: Upsampling High
eg. signal now 705.6kHz
To open the CD lid, locate the hinge at
the rear and gently lever the sprung
mechanism in a fluid downward
motion (never apply force). Gently
use the hinge to lever the lid open or
closed.
134
5
2
PROGRAM SCAN SHUFFLE
TRACK
A - B
TOTAL
REPEAT 1
REM TIME
PAUSE
12
34
5
Track no.
Seconds
Play status
Dual data indicator
Minutes
All basic CD functions can be accessed through the top pannel
buttons. Below is a diagram of the screen section system, using the
top panel buttons to navigate.