Chrysler 300 2019 User manual

 QUICK REFERENCE GUIDE
CHRYSLER 300

Vehicle User Guide —
If Equipped
To access the Vehicle User Guide on your Uconnect
Touchscreen: Tap the Uconnect Apps button, then
tap the Vehicle User Guide icon on your touchscreen.
No Uconnect registration is required.
NOTE:
Vehicle User Guide features are not available while the
vehicle is moving.
Features
• Your User Guide — Updated in real-time
• Available when and where you need it
• Touchscreen convenience
• Customizable interface
• Maintenance schedules and information
• Multilingual
• Comprehensive icon & symbol glossary
Keyless Enter-N-Go —
Passive Entry
The Keyless Enter-N-Go system is an enhancement
to the vehicle’s key fob. This feature allows you to lock
and unlock the vehicle’s door(s) and trunk without
having to press the key fob lock or unlock buttons.
Uconnect 4C NAV With 8.4–inch Display
Vehicle User Guide Touchscreen Icon
VEHICLE USER GUIDE
— IF EQUIPPED PASSIVE ENTRY

To Unlock From The Driver
Or Passenger Side
With a valid Keyless Enter-N-Go key fob located
outside the vehicle and within 5 ft (1.5m) of the driver
or passenger side door handle, grab either front door
handle to unlock the door automatically.
To Lock The Vehicle
• Both front door handles have buttons located on
the outside of the handle. With one of the vehicle's
Keyless Enter-N-Go key fobs located outside the
vehicle and within 5 ft (1.5 m) of the driver's or
passenger front door handle, push the door handle
button to lock all four doors and trunk.
• DO NOT grab the door handle, when pushing the
door handle button. This could unlock the door(s).
NOTE:
• If “Unlock All Doors 1st Press” is programmed, all
doors will unlock when you grab hold of the front
driver's door handle.
• If “Unlock All Doors 1st Press” is programmed, all
doors and trunk will unlock when you push the trunk
button. If “Unlock Driver Door 1st Press” is pro-
grammed, only the trunk will unlock when you push
the trunk button.
Grab The Door Handle To Unlock
Push The Door Handle Button To Lock
Do Not Grab The Door Handle When Locking

• If a key fob is detected in the vehicle when locking
the vehicle using the power door lock switch, the
doors and trunk will unlock, and the horn will chirp
three times. On the third attempt, your key fob can
be locked inside the vehicle.
• After pushing the Keyless Enter-N-Go lock button,
you must wait two seconds before you can lock or
unlock the vehicle using the door handle. This is
done to allow you to check if the vehicle is locked
by pulling the door handle without the vehicle re-
acting and unlocking.
• If a Keyless Enter-N-Go door handle has not been
used for 72 hours, the Keyless Enter-N-Go feature
for that handle may time out. Pulling the deacti-
vated front door handle will reactivate the door
handle's Keyless Enter-N-Go feature.
To Enter The Trunk • With a valid Keyless Enter-N-Go key fob located
outside the vehicle and within 5 ft (1.5 m) of the
deck lid, push the button located on the center of
the light bar which is located on the deck lid above
the license plate.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html (U.S.
Residents) or www.owners.mopar.ca (Canadian Resi-
dents).
Trunk Unlock Button

Cluster Display
The instrument cluster display features a driver inter-
active display that is located in the instrument cluster.
Pushing the controls on the left side of the steering
wheel allows the driver to select Vehicle Information
and Personal Settings.
• Push the up arrow button to scroll upward through
the main menus (Speedometer, Vehicle Info, Driver
Assist, Fuel Economy, Trip, Audio, Messages,
Screen Setup) and sub menus.
• Push the down arrow button to scroll downward
through the main menus and sub menus.
• Push the right arrow button to scroll forward to the
next menu or sub menu.
• Push the left arrow button to scroll back to a pre-
vious menu or sub menu.
• Push the OK button to access/select the informa-
tion screens, the submenu screens of a main menu
item, or to select a personal setting in the setup
menu. Push and hold the OK button for two sec-
onds to reset displayed/selected features that can
be reset.
Compass Calibration
This compass is self-calibrating, which eliminates the
need to set the compass manually. When the vehicle is
new, the compass may appear erratic, and the cluster
will display dashes (- -) until the compass is calibrated.
You may also calibrate the compass by completing
one or more 360 degree turns (in an area free from
large metal or metallic objects) until the dashes (- -)
displayed in the cluster turn off. The compass will now
function normally.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html (U.S.
Residents) or www.owners.mopar.ca (Canadian Resi-
dents).
Instrument Cluster Display Controls
INSTRUMENT
CLUSTER DISPLAY

Pairing Procedure
Mobile phone pairing is the process of establishing a
wireless connection between a cellular phone and the
Uconnect system.
Start Pairing Procedure On The Radio
Uconnect 4C, 4C NAV:
1. Place the ignition in the ACC or ON position.
2. Press the “Phone” button in the Menu Bar on the
touchscreen.
3. Select “Settings.”
4. Select “Paired Phones.”
5. Select “Add device.”
• Uconnect Phone will display an “In progress”
screen while the system is connecting.
Pair Your iPhone:
To search for available devices on your Bluetooth
enabled iPhone:
1. Press the Settings button.
2. Select Bluetooth.
• Ensure the Bluetooth feature is enabled. Once
enabled, the mobile phone will begin to search
for Bluetooth connections.
3. When your mobile phone finds the Uconnect sys-
tem, select “Uconnect”.
Uconnect4C&4CNAV
Bluetooth On/Uconnect Device
PHONE PAIRING

Complete The iPhone Pairing Procedure:
1. When prompted on the mobile phone, accept the
connection request from Uconnect Phone.
NOTE:
Some mobile phones will require you to enter the PIN
number.
Pair Your Android Device:
To search for available devices on your Bluetooth
enabled Android Device:
1. Push the Menu button.
2. Select Settings.
3. Select Connections.
4. Turn Bluetooth setting to “On.”
• Ensure the Bluetooth feature is enabled. Once
enabled, the mobile phone will begin to search
for Bluetooth connections.
5. Once your mobile phone finds the Uconnect sys-
tem, select “Uconnect”.
• You may be prompted by your mobile phone to
download the phonebook, check “Do Not Ask
Again” to automatically download the phone-
book. This is so you can make calls by saying
the name of your contact.
Pairing Request Uconnect Device

Complete The Android Pairing Procedure:
1. Confirm the passkey shown on the mobile phone
matches the passkey shown on the Uconnect sys-
tem then accept the Bluetooth pairing request.
NOTE:
Some mobile phones require the PIN to be entered
manually, enter the PIN number shown on the
Uconnect screen.
For further information on Uconnect Phone, please
refer to “Uconnect Phone” in your Uconnect Owner’s
Manual Supplement.
Automatic High Beam —
If Equipped
This system automatically controls the operation of
the headlamp high beams as oncoming vehicles ap-
proach.
• The Automatic High Beam Headlamp Control can
be turned on or off using the Uconnect System.
• Push the turn signal lever away from you.
• With the headlight switch in the “AUTO” position,
the high beams are controlled automatically.
• Pull the turn signal lever toward you to manually
deactivate the system.
• To improve system recognition of crossing traffic,
and to limit use in a residential area, the vehicle
must be moving at a speed greater than 20 mph
(32 km/h) before the Automatic High Beam Mod-
ule (AHBM) begins requesting high beam
activation.
Pairing Request
LIGHTS

NOTE:
If the windshield or Automatic High Beam Headlamp
Control mirror is replaced, the mirror must be re-
aimed to ensure proper performance. See a local au-
thorized dealer.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html (U.S.
Residents) or www.owners.mopar.ca (Canadian Resi-
dents).
Speed Control
When engaged, the Speed Control takes over accel-
erator operations at speeds greater than 25 mph
(40 km/h).
To Activate
Push the on/off button. To turn the system off, push
the on/off button a second time. The system should
be turned off when not in use.
To Set A Desired Speed
Turn the Speed Control on. When the vehicle has
reached the desired speed, push the SET (+) or the
SET (-) button and release. Release the accelerator
and the vehicle will operate at the selected speed.
To Deactivate
A soft tap on the brake pedal, pushing the CANC
button, or normal brake pressure while slowing the
vehicle will deactivate Speed Control without erasing
the set speed memory. Pushing the on/off button or
turning the ignition switch OFF erases the set speed in
memory.
To Resume Speed
To resume a previously set speed, push the RES but-
ton and release.
Speed Control Switches
1 — Push Cancel
2 — Push Set (+)/Accel
3 — Push Resume
4 — Push On/Off
5 — Push Set (-)/Decel
SPEED CONTROL

To Increase Speed
When the Speed Control is set, you can increase
speed by pushing the SET (+) button.
To Decrease Speed
When the Speed Control is set, you can decrease
speed by pushing the SET (-) button.
To Accelerate For Passing
Press the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set
speed.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html (U.S.
Residents) or www.owners.mopar.ca (Canadian Resi-
dents).
Adaptive Cruise Control
(ACC) — If Equipped
If your vehicle is equipped with Adaptive Cruise Con-
trol, the controls operate exactly the same as the
standard cruise control, with one difference. You can
set a specified distance you would like to maintain
between you and the vehicle in front of you.
• If the ACC sensor detects a vehicle ahead, ACC
will apply limited braking or acceleration automati-
cally to maintain a preset following distance while
matching the speed of the vehicle ahead.
• If the sensor does not detect a vehicle directly
ahead of you, it functions like a standard cruise
control system, maintaining the speed you set.
For further information, and applicable warnings and
cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html (U.S.
Residents) or www.owners.mopar.ca (Canadian Resi-
dents).
Adaptive Cruise Switches
1 — Adaptive Cruise Control (ACC) On/Off
2 — Distance Setting – Decrease
3 — Distance Setting – Increase