Circle Specialty Pango Activity Chair PA1200 User manual

Pango Activity Chair
USER MANUAL
www.circlespecialty.com
Pango Activity Chair
PA1200
PA1400
Item #s
Seat Height – Place seat on its back, remove securing screw (A)
from each inner leg and detach all 4 outer legs. Position each
outer leg at its desired height, insert screw (A) and tighten.
Additional height can be achieved by changing the placement of
the inner pin (B).
NOTE: Anterior or posterior seat tilt can be achieved by posi-
tioning front and back legs at different heights.
Seat Depth- Loosen knobs (C) under the seat and adjust to
desired position by sliding the seat forward or backwards.
Seat Width – Hip Guide accessories are available to reduce seat
width and to provide additional support to child’s hips. They are
secured to the inside of the armrest using the hook and loop
fastener provided.
Seat to Floor Angle – The Pango can be adjusted in increments
of 5º from 850- 900- 950. Factory setting is at 900. To change the
angle, remove screws (D), position seat at the desired angle and
tighten the screw (D).
Back Angle – The Pango can be adjusted in increments of 5º
from 950- 1000- 1050. Factory setting is at 950. To change the
angle, remove knobs (E), position back at the desired angle and
tighten the knobs (E).
Armrest- Loosen knob (F), slide armrest up or down to desired
position and tighten knob (F).
NOTE: Armrests must be at same height when using the tray
accessory.
Pelvic Belt- The pelvic belt is secured to the seat by two cam
locks under the seat. To adjust the belt, lift each cam lock (G),
adjust the straps to desired length and close each cam lock. The
padded side-release buckle (H) should be placed with the buckle
facing away from the child and the pad placed behind the buckle
for comfort and protection.
1

Seat Height – Place seat on its back, remove securing screw (A)
from each inner leg and detach all 4 outer legs. Position each
outer leg at its desired height, insert screw (A) and tighten.
Additional height can be achieved by changing the placement of
the inner pin (B).
NOTE: Anterior or posterior seat tilt can be achieved by posi-
tioning front and back legs at different heights.
Seat Depth- Loosen knobs (C) under the seat and adjust to
desired position by sliding the seat forward or backwards.
Seat Width – Hip Guide accessories are available to reduce seat
width and to provide additional support to child’s hips. They are
secured to the inside of the armrest using the hook and loop
fastener provided.
Seat to Floor Angle – The Pango can be adjusted in increments
of 5º from 850- 900- 950. Factory setting is at 900. To change the
angle, remove screws (D), position seat at the desired angle and
tighten the screw (D).
Back Angle – The Pango can be adjusted in increments of 5º
from 950- 1000- 1050. Factory setting is at 950. To change the
angle, remove knobs (E), position back at the desired angle and
tighten the knobs (E).
Armrest- Loosen knob (F), slide armrest up or down to desired
position and tighten knob (F).
NOTE: Armrests must be at same height when using the tray
accessory.
Pelvic Belt- The pelvic belt is secured to the seat by two cam
locks under the seat. To adjust the belt, lift each cam lock (G),
adjust the straps to desired length and close each cam lock. The
padded side-release buckle (H) should be placed with the buckle
facing away from the child and the pad placed behind the buckle
for comfort and protection.
Thank you for purchasing your Pango Acvity Chair.
The Pango is designed to aid in postural support for chil-
dren with mild to moderate requirements. This versatile
seat is perfect in school, clinic and home environments.
To safely operate and maintain your activity chair, please
read this User Manual carefully before using activity
chair and save it for future reference.
Taking proper care of your activity chair will ensure lon-
gevity and that you fully benefit from its features.
The Pango is CE marked and meets the essenal
requirements of all relevant European Medical
Device Direcves.
INTRODUCTION
2

Seat Height – Place seat on its back, remove securing screw (A)
from each inner leg and detach all 4 outer legs. Position each
outer leg at its desired height, insert screw (A) and tighten.
Additional height can be achieved by changing the placement of
the inner pin (B).
NOTE: Anterior or posterior seat tilt can be achieved by posi-
tioning front and back legs at different heights.
Seat Depth- Loosen knobs (C) under the seat and adjust to
desired position by sliding the seat forward or backwards.
Seat Width – Hip Guide accessories are available to reduce seat
width and to provide additional support to child’s hips. They are
secured to the inside of the armrest using the hook and loop
fastener provided.
Seat to Floor Angle – The Pango can be adjusted in increments
of 5º from 850- 900- 950. Factory setting is at 900. To change the
angle, remove screws (D), position seat at the desired angle and
tighten the screw (D).
Back Angle – The Pango can be adjusted in increments of 5º
from 950- 1000- 1050. Factory setting is at 950. To change the
angle, remove knobs (E), position back at the desired angle and
tighten the knobs (E).
Armrest- Loosen knob (F), slide armrest up or down to desired
position and tighten knob (F).
NOTE: Armrests must be at same height when using the tray
accessory.
Pelvic Belt- The pelvic belt is secured to the seat by two cam
locks under the seat. To adjust the belt, lift each cam lock (G),
adjust the straps to desired length and close each cam lock. The
padded side-release buckle (H) should be placed with the buckle
facing away from the child and the pad placed behind the buckle
for comfort and protection.
Unpack the activity chair and prepare for use.
Your Pango Activity Chair arrives fully assembled and includes an
adjustable cushioned seat, back, armrest, pelvic belt, and legs.
• Never leave child unattended in this product.
• Before use, caregiver should be familiar with the function and
adjustments of the chair.
• Complete all positioning adjustments and fasten securely
before placing child in the chair.
• The chair is designed for indoor use and should only be used on
a flat surface.
• Only use Circle Specialty components and accessories with this
product. Failure to do so may put the user at risk and will invali-
date the warranty.
GENERAL USE
SAFETY
3

ADJUSTMENTS
Seat Height – Place seat on its back, remove securing screw (A)
from each inner leg and detach all 4 outer legs. Position each
outer leg at its desired height, insert screw (A) and tighten.
Additional height can be achieved by changing the placement of
the inner pin (B).
NOTE: Anterior or posterior seat tilt can be achieved by posi-
tioning front and back legs at different heights.
A
B
Seat Height
Seat Depth C
Seat Depth- Loosen knobs (C) under the seat and adjust to
desired position by sliding the seat forward or backwards.
Seat Width – Hip Guide accessories are available to reduce seat
width and to provide additional support to child’s hips. They are
secured to the inside of the armrest using the hook and loop
fastener provided.
Seat to Floor Angle – The Pango can be adjusted in increments
of 5º from 850- 900- 950. Factory setting is at 900. To change the
angle, remove screws (D), position seat at the desired angle and
tighten the screw (D).
Back Angle – The Pango can be adjusted in increments of 5º
from 950- 1000- 1050. Factory setting is at 950. To change the
angle, remove knobs (E), position back at the desired angle and
tighten the knobs (E).
Armrest- Loosen knob (F), slide armrest up or down to desired
position and tighten knob (F).
NOTE: Armrests must be at same height when using the tray
accessory.
Pelvic Belt- The pelvic belt is secured to the seat by two cam
locks under the seat. To adjust the belt, lift each cam lock (G),
adjust the straps to desired length and close each cam lock. The
padded side-release buckle (H) should be placed with the buckle
facing away from the child and the pad placed behind the buckle
for comfort and protection.
4

Seat Height – Place seat on its back, remove securing screw (A)
from each inner leg and detach all 4 outer legs. Position each
outer leg at its desired height, insert screw (A) and tighten.
Additional height can be achieved by changing the placement of
the inner pin (B).
NOTE: Anterior or posterior seat tilt can be achieved by posi-
tioning front and back legs at different heights.
Seat Depth- Loosen knobs (C) under the seat and adjust to
desired position by sliding the seat forward or backwards.
E
Back Angle
Seat Width – Hip Guide accessories are available to reduce seat
width and to provide additional support to child’s hips. They are
secured to the inside of the armrest using the hook and loop
fastener provided.
Seat to Floor Angle – The Pango can be adjusted in increments
of 5º from 850- 900- 950. Factory setting is at 900. To change the
angle, remove screws (D), position seat at the desired angle and
tighten the screw (D).
D
Seat to Floor Angle
Back Angle – The Pango can be adjusted in increments of 5º
from 950- 1000- 1050. Factory setting is at 950. To change the
angle, remove knobs (E), position back at the desired angle and
tighten the knobs (E).
Armrest- Loosen knob (F), slide armrest up or down to desired
position and tighten knob (F).
NOTE: Armrests must be at same height when using the tray
accessory.
Pelvic Belt- The pelvic belt is secured to the seat by two cam
locks under the seat. To adjust the belt, lift each cam lock (G),
adjust the straps to desired length and close each cam lock. The
padded side-release buckle (H) should be placed with the buckle
facing away from the child and the pad placed behind the buckle
for comfort and protection.
5

Seat Height – Place seat on its back, remove securing screw (A)
from each inner leg and detach all 4 outer legs. Position each
outer leg at its desired height, insert screw (A) and tighten.
Additional height can be achieved by changing the placement of
the inner pin (B).
NOTE: Anterior or posterior seat tilt can be achieved by posi-
tioning front and back legs at different heights.
Seat Depth- Loosen knobs (C) under the seat and adjust to
desired position by sliding the seat forward or backwards.
Seat Width – Hip Guide accessories are available to reduce seat
width and to provide additional support to child’s hips. They are
secured to the inside of the armrest using the hook and loop
fastener provided.
Seat to Floor Angle – The Pango can be adjusted in increments
of 5º from 850- 900- 950. Factory setting is at 900. To change the
angle, remove screws (D), position seat at the desired angle and
tighten the screw (D).
Back Angle – The Pango can be adjusted in increments of 5º
from 950- 1000- 1050. Factory setting is at 950. To change the
angle, remove knobs (E), position back at the desired angle and
tighten the knobs (E).
F
Armrest
Pelvic Belt
G
H
Armrest- Loosen knob (F), slide armrest up or down to desired
position and tighten knob (F).
NOTE: Armrests must be at same height when using the tray
accessory.
Pelvic Belt- The pelvic belt is secured to the seat by two cam
locks under the seat. To adjust the belt, lift each cam lock (G),
adjust the straps to desired length and close each cam lock. The
padded side-release buckle (H) should be placed with the buckle
facing away from the child and the pad placed behind the buckle
for comfort and protection.
6

• Wash the Pango Activity Chair frequently with a damp cloth and
mild detergent.
• Do not use strong detergents, abrasive products, or dry-cleaning
solvents.
• A soft brush may be used for stubborn or heavily ingrained
marks.
• Do not immerse the activity chair in water.
• The pelvic strap can be removed, and machine washed
Inspect the acvity chair to ensure:
• There are no cracks or splits on the wood components
• There are not tears or worn parts on the upholstery
• All knobs and screws are securely fastened
• The straps are not frayed nor the buckles damaged
CARE AND MAINTENANCE
Seat Height – Place seat on its back, remove securing screw (A)
from each inner leg and detach all 4 outer legs. Position each
outer leg at its desired height, insert screw (A) and tighten.
Additional height can be achieved by changing the placement of
the inner pin (B).
NOTE: Anterior or posterior seat tilt can be achieved by posi-
tioning front and back legs at different heights.
Seat Depth- Loosen knobs (C) under the seat and adjust to
desired position by sliding the seat forward or backwards.
Seat Width – Hip Guide accessories are available to reduce seat
width and to provide additional support to child’s hips. They are
secured to the inside of the armrest using the hook and loop
fastener provided.
Seat to Floor Angle – The Pango can be adjusted in increments
of 5º from 850- 900- 950. Factory setting is at 900. To change the
angle, remove screws (D), position seat at the desired angle and
tighten the screw (D).
Back Angle – The Pango can be adjusted in increments of 5º
from 950- 1000- 1050. Factory setting is at 950. To change the
angle, remove knobs (E), position back at the desired angle and
tighten the knobs (E).
Armrest- Loosen knob (F), slide armrest up or down to desired
position and tighten knob (F).
NOTE: Armrests must be at same height when using the tray
accessory.
Pelvic Belt- The pelvic belt is secured to the seat by two cam
locks under the seat. To adjust the belt, lift each cam lock (G),
adjust the straps to desired length and close each cam lock. The
padded side-release buckle (H) should be placed with the buckle
facing away from the child and the pad placed behind the buckle
for comfort and protection.
7

This warranty is solely for the benefit of the original consumer
purchaser and is in effect from date of purchase.
Circle Specialty Inc. warranties that the Pango Activity Chair will
be free from defect for a period of two (2) years.
The warranty does not extend to non-durable components or any
components that are subject to standard wear and tear.
This warranty does not cover device failure due to owner misuse
or negligence. It only applies when product is used according to the
specified conditions and for the intended purposes.
If within the warranty period any such product shall be proved
defective, such product will be repaired or replaced at Circle Spe-
cialty’s option.
If you have a question about your Circle Specialty walker or this
warranty, please contact an authorized dealer.
WARRANTY
Circle Specialty, Inc.
Brooklyn, NY 11232, USA
718.943.6452
[e-mail]
2020/Rev 3-20
Seat Height – Place seat on its back, remove securing screw (A)
from each inner leg and detach all 4 outer legs. Position each
outer leg at its desired height, insert screw (A) and tighten.
Additional height can be achieved by changing the placement of
the inner pin (B).
NOTE: Anterior or posterior seat tilt can be achieved by posi-
tioning front and back legs at different heights.
Seat Depth- Loosen knobs (C) under the seat and adjust to
desired position by sliding the seat forward or backwards.
Seat Width – Hip Guide accessories are available to reduce seat
width and to provide additional support to child’s hips. They are
secured to the inside of the armrest using the hook and loop
fastener provided.
Seat to Floor Angle – The Pango can be adjusted in increments
of 5º from 850- 900- 950. Factory setting is at 900. To change the
angle, remove screws (D), position seat at the desired angle and
tighten the screw (D).
Back Angle – The Pango can be adjusted in increments of 5º
from 950- 1000- 1050. Factory setting is at 950. To change the
angle, remove knobs (E), position back at the desired angle and
tighten the knobs (E).
Armrest- Loosen knob (F), slide armrest up or down to desired
position and tighten knob (F).
NOTE: Armrests must be at same height when using the tray
accessory.
Pelvic Belt- The pelvic belt is secured to the seat by two cam
locks under the seat. To adjust the belt, lift each cam lock (G),
adjust the straps to desired length and close each cam lock. The
padded side-release buckle (H) should be placed with the buckle
facing away from the child and the pad placed behind the buckle
for comfort and protection.
8