Ciro HILLCART Flatlander User manual

Looking after
- Regularly wash with neutral cleaner, rinse and dry.
Do not use a jet cleaner. Keep bearings dry.
Water or other fluids may damage them.
- After cleaning, check all parts for wear and dents.
- Never oil or grease the pole fitting area.
Use dry lubricants like Teflon spray only.
Keep the pole fitting area always clean.
If the pole goes strong, grind it with fine emery.
- Clean the wheel bearings on a regularly basis.
Replace worn wheel bearings.
Warranty
- Raceboards are guaranteed against defects in
material and manufacturing for the warranty period
provided by law ** from the date of purchase. The
warranty only covers the defective component, not
the complete Raceboard. The warranty excludes
damage due to transport or storage. All responsibility
is declined in case of not following the instructions
for use, wear and tear (especially wheels, bearings,
steering rod, brakes, cables, stepping boards and
handlebar grips), use other than for which the
Raceboard has been designed, poor maintenance
and servicing or damage cased by accident or fall.
If a claim is entered into, a substitute or repair will
be provided within a suitable period. The buyer
covers all costs for packaging and transportation,
if components or entire Raceboard are sent without
consent or a claim is found to be unwarranted. This
warranty only covers products sold by an authorized
dealer and applies to the first user and is not trans-
ferable. For warranty service present the defective
product together with the original sales receipt to
your nearest authorized Ciro dealer.
Your statutory rights are not affected.
** The warranty period may vary from
country to country.
Turning
- Move joystick/handlebar to the right or left, wheels
follow suit. Do not pull or jerk the joystick/handlebar,
use balance to steer.
- When the wheels follow an unevenness, correct
direction of travel carefully.
- When the steering starts to oscillate, immediately
reduce speed. Models with steering damper only:
correct the force of the steering damper.
Loosen: easy steering. Fasten: stiff steering.
Braking
- Operate the brake carefully. Locked wheels can
develop flat spots and become out of round very fast!
- During braking the brake becomes hot.
Touching the brake may lead to burns!
Footbrake only: do not ride downhill and in the wet,
because the brake may become totally ineffective
Discbrake only: take care in the wet, the brake may
lock suddenly and the Raceboard could slide!
Checking over
- Check for function and damages before every ride.
- Check all parts for cracks and dents.
Replace damaged parts immediately!
- Discbrake only: Pull the brake lever for 30 seconds.
The brake lever must not slacken. If the lever slackens,
the brake system is leaky. Do not ride on, see your
authorized dealer immediately for repair!
- Mind for wear in steering, steering pole settings
and wheels!
- Regularly tighten all bolts and nuts, especially
wheel- and steering rod bolts and screws.
- Consult your dealer after accidents or if you
discover strange wear patterns.
Code of Responsibility
- Be aware that Racer-boarding, like other recrea-
tional activities, involves inherent and other risks
which may lead to injury or even death. Maintain
caution, presence of mind and control of speed in
all situations to board safely.
- Wear shoes with rubber soles. Protective gear
including helmet, wrist guards, elbow and knee
pads are strongly recommended. Understand that
no amount of protective gear can protect you in all
situations.
- Never ride under the influence of drugs or alcohol.
- Become familiar with your Raceboard, learn how
to mount, turn and stop.
- Follow the highway code, avoid areas with heavy
traffic.
- Watch the traffic carefully, look ahead and give way
if necessary. Alert other road users of your
presence, especially pedestrians when passing.
- Never allow yourself to be pulled by other vehicles.
Do not use your Raceboard on wet, oily, icy or rough
uneven surfaces.
- Do not pull or push the joystick/handlebar pole while
in motion. Do not lean back, do not jump over land-
ings or down steps as you may bend the board and
crash.
- Keep your Raceboard in good running order.
Do not modify it in any way as this could bear risks
and will invalidate your warranty.
- Your responsibility is without limitation to the above.
- In addition to this code you should be in good
physical condition.
state: 01.01.13

Instructions for Use
of your
Ciro/HILLCART Raceboard
read full instructions before setting off
How to take off the pole
open the lever of the clamp
press the nipple at the pole
take off the pole by turning
How to brace the board (HILLCART only)
to increase the tension of the board, turn the lower nut
anti clockwise (spanner 13mm)
Content
1 x Ciro / HILLCART Raceboard
1 x pole *
2 x wheelz *
2 x hex head screw *
2 x big washer *
2 x spacer (or little washer depending on model) *
2 x nylon nut *
1 x box spanner 13mm
1 x hex key wrench 5mm
*) Only if the product is partly assembled. For spare parts and
accessories see your local dealer or contact us directly.
How to set the pole
open the lever of the clamp
press the nipple at the pole
whilsts turning put the pole into
the dome until the nipple fits
when the nipple fits with a “click“
close the lever of the clamp
if necessary tighten the lever by
turning the curled nut clockwise
Ciro Shop - Straka.DES
Markt 2
08340 Schwarzenberg
Germany
fon: [phone]
fax: [phone]
mail: [email protected]
web: www.ciro.de
How to mount the wheelz
put the hex head screw through
the bracket from the inside
first slide the big washer onto the
screw,
then the spacer (or little washer
depending on the model),
follow the wheel
(the hollow side is the inside,
note the turning direction),
last screw on the nylon nut tight
(spanner 13mm)
when finished, check the running
performance of the wheelz
HILL CAR
HILL CARHILL CAR
HILL CART
TT
T
®