Clear blue hawaii Hanauma User manual

Inflatable Kayak Instructions

Thank you for purchasing your Clear Blue Hawaii kayak.

Deflation / Storage

Care and maintenance

Our assembly manual is designed to guide you through the simple assembly process of your Clear Blue Hawaii Kayak, even if you are new to this exciting sport. This document acts as a

useful quick reference and 'working document' that provides all necessary information for use, maintenance, care and safety. Please read these instructions carefully as we guide you

through the assembly process step-by-step.

Inflating your Clear Blue Hawaii Kayak

Before starting, locate a relatively flat, clean space to unpack your boat.

Remove the Kayak from its packaging and unroll the kayak so it is laid out

flat on the ground. You will find that the kayak has four inflatable chambers,

two of which come equipped with Boston valves at the bow and stern and

the other two valves in the seating areas.

After you have identified the parts of the kayak, use a standard, traditional

manual pump that you can buy at any sports department store (not included

in the package) to inflate the kayak. It might harm the Kayak to use an air

compressor designed for auto tires as the boat is designed to work at a far

lower working pressure, so we recommend only using manual pumps or

electrical pumps specifically designed for inflatables.

Your Kayak is ready for use now. Enjoy!

First, inflate the right-hand side chamber of the kayak. Inflate only one chamber

at a time until the kayak has achieved the desired rigidity.

First deflate the kayak entirely.

Once the boat is rolled up, you can easily store or carry it.

Store your kayak in a clean, dry area away from extreme changes in

environmental conditions

Starting from the stern, roll the kayak up like you would roll up a sleeping bag. It

is important to roll it tightly for compact storage.

There is not much that you need to keep in mind when caring for the Hanauma, if

you follow some basic guidelines, it will remain in almost new condition for many

years. It can be stored either inflated or deflated. Inspect and rinse your kayak and

all accessories after use to prevent salt drying on the kayak (if used in salt water).

This can be done with the use of a mild soapy solution, please avoid detergents or

any type of silicone-based products. When storing the Hanauma in confined

spaces, please ensure it is completely clean and dry so that it does not get mold.

When storing it outside, we advise to protect it with a tarp against direct sunlight,

rain, leaves, and so on. In extremely cold temperatures, the PVC might become

brittle; we therefore do not recommend using it in temperatures below 32 degrees

Fahrenheit (0 degrees Celsius).

Fold one side of the kayak toward the center.

Next fold the other side so that it overlaps over the first. There will still be some

air in the kayak. This is normal and no reason to worry.

The straps are adjustable for a comfortable seating position. Position the seats

to your preferences by simply adjusting the buckles and webbing.

Before use, make sure that all valves are tightened to avoid leakage.

Insert the seats and position them on the deck identifiable by Velcro strips.

You should plan on storing the Hanauma for more than a few days, it is advisable

to towel it off or let the kayak dry in the sun and then deflate and store it.

CLEAR BLUE HAWAI I

www.clearbluehawaii.com

2123 Eluwene St. Honolulu, HI 96819

Tel : (808) 832-2438 Fax : (808) 832-2439

WARNING

When boating: learn and respect the local regulations and practices. Do not neglect the

safety rules as this could jeopardize your life and the lives of others.

Before setting off, make sure you are thoroughly briefed and feel comfortable with

operating the boat. You will be responsible not only for its safe and correct operation but

also for the behavior and safety of yourself and your passengers.

Never leave land without the essential safety equipment: lifejackets (PDFs), foot-pump,

repair kit, paddles, and other necessary equipment that might be required by law in your

area.

Do not exceed the authorized number of persons or weight.

Make sure your passengers remain seated. We will take no responsibility if this warning

is disregarded.

No alcohol or drugs: Do not drink alcohol or take drugs before or while operating your

boat. Maintain passengers sobriety.

FOR USE AS A RECREATIONAL/TOURING KAYAK ON CALM WATER, NOT

SUITABLE FOR RAPIDS OR ROUGH SEA. THIS IS NOT A WHITE WATER OR SURF

KAYAK. TO BE CONTROLLED BY SOMEONE EXPERIENCED ON THE WATER AND

APPROPRIATE WATER CONDITIONS, RECOGNIZE THE LIMITS OF YOUR ABILITY.

UNDERSTAND YOUR SURROUNDINGS, WEATHER, AND BE ALERT FOR OTHER

VESSELS ON THE WATER.

Repair

Even though the Kayak is highly puncture-resistant, occasionally punctures can

occur. It is relatively easy to repair these leaks and should only take a few minutes

even for inexperienced users. Repair kits can be bought at sporting goods stores.

Larger Leaks need to be patched. Patching should only take a few minutes. Please

follow these steps :

Deflate the Kayak.

Remove dirt or grime from area of leak and thoroughly dry it.

The area to be repaired needs to be clean and dry.

Apply a small drop of glue on small punctures (less than 1/8 th ") and let glue

dry for 12 hours. If you need to use the Kayak sooner, let dry the glue for 30

minutes to one hour.

Locate the leak. This can be done by visual inspection, listening for air leakage

in quiet surroundings or by spraying soap water over the area of the boat where

you suspect a leak. A leak will produce bubbles showing the location of the

leak.

Cut out a large enough patch from the repair material, put it over the leak and

trace it with a ballpoint pen. If you angle the pen inward, the outline will be

covered by the patch and thereby invisible after the repair.

After inflation, your Kayak is ready for usage again, yet a permanent repair still

needs to be made later.

Then inflate the boat; yet only inflate the repaired compartment about 3/4 full.

When patch is dry, seal off edges with glue and let dry for four more hours.

After inflation, your Hanauma is ready for use again.

Let the glue dry for a few minutes until it appears to be tacky.

Apply glue to the underneath side of the repair patch and on the leak area. The

affected areas need to be coated lightly but effectively with the glue.

Place the patch on the area and press it down firmly. Place a heavy weight

(several pounds) over the repaired area and let dry for 12 hours.

Do not swallow the glue or inhale vapors

Avoid contact with the eyes and skin

All repairs must be done in an open area and/or with excellent ventilation

All items must be kept out of the reach of children, this includes glue,

solvents and other dangerous materials