Color-mono AC24V User manual

Thank you for choosing this high quality camera, before attempting to
onnect or operate this product, please read these instructions completelyc
DIGITAL COLOR VIDEO CAMERA
HIGH RESOLUTION
STD. RESOLUTION
AC24V/12VDC Model
1/3” CCD Sensor
OPERATING MANUAL
Warning: To prevent fire or electric shock hazard, do not expose
the appliance to rain or moisture
P02-D0-014-C

General
This color CCD video camera employs a 1/3 inch charge coupled device
solid-state imaging device with 470/410 k or 310/270k picture elements, This
unit is equipped with a newly developed DSP (Digital Signal Processor) for
processing the video signal. A micro-controller is also introduced to provide
high color reproduction, sharp, stable picture and most of the function’s control;
the special feature for this camera is it can accept IR illumination under
minimal lighting condition.
Features
 Accept IR illumination for completely dark surveillance, daytime color and auto
swap to black-white picture at night.
 480 /380 lines of horizontal resolution and high quality picture by utilizing digital
processing LSI’s
 Minimum illumination of 0.5 lux and signal-to-noise ratio of 48 dB is realized by
employing a high sensitivity image sensor with micro lenses and low noise circuit
design.
 High quality picture –A digital signal processor performs digital horizontal and
vertical aperture enhancement to produce high-resolution picture.
 A newly developed intelligent wide range Auto Tracing White Balance (ATW) that
automatically adjusts the tone according to the color temperature of the light
source illuminating the subject.
 Smart digital control Auto BLC, the combination of Histogram equalizer and
Central windows weighting BLC functions ensure for use against any unusual
lighting conditions.
 Advanced Auto Exposure System for both fix iris and auto iris lenses control the
amount of light to ensure it is always optimized.
 Internal or Line-lock external sync
.
-2 -

-3 -
I
IV
VI
III
GVO PW- PW+
DOWN
UP
JUMP
II
V
Name of Parts and Functions
A. Camera
Threaded for 3/4-inch Conduit.
(Plug Supplied.)
148.92 [5.87]
145.16 [5.72]
54 [2.13]
101.2 [3.99]
Threaded for 3/4-inch Conduit
G
B
F
D
C
A
E
B. PC assembly
I. Power source: AC24V/DC12V Block Terminal
II. Video out
III. UTP module connection
IV. Line-lock Phase Adj. (Line-lock model)
V. Jumpers disconnected to engage UTP module
VI. DC auto iris level adjustment pot
For DC drive auto iris lens driving level adjustment
in order to obtain correct exposure light.
C. Back conduit entry
D. Side conduit entry
E. Inner plate mounting holes
F. Security screw
G. Plug.

White Balance
ATW mode----.
In this mode, the color temperature is monitoring continuous, and the
white balance is set automatically by internal micro-controller.
The operating color temperature range is from 2500°K to 9500°K
approximately.
Auto Back-light Compensation
This intelligent auto BLC is a newly developed digital light level control system, it is
activated automatically by screen histogram (contrast) and 225 area window
weighting integration to control iris gain and white balance simultaneous, so that the
clear object with adequate light level can always be optimized.
Central Window Weighted average Backlight compensation
This method is suited for cases where the main subject is fixed within the screen.
Histogram Backlight compensation
This method is suited for cases where the main subject moves about within the screen.
The combination of two types Backlight makes it easier to arrange Backlight
compensation operation to match the imaging conditions and installation location.
Note: Compensation may be insufficient when the background is extremely
bright
Line-Lock Phase Adjustment
DOWN
UP
The vertical phase of the camera video signal can be matched to the phase of
AC power line.
Using a dual-trace oscilloscope to observe the video output signal (V-rate) of
the camera and adjust the Line-lock Phase control buttons to line up the
phase of both signals
Caution: The adjustment must be
made by qualified servicing
person or system installer.
Phase adjusting Buttons for both
Line-lock models.
Adjusting the camera zoom and focus
1. Loosen the zoom ring thumbscrew.
2. Turn the zoom ring to set the desired zoom.
3. Tighten the zoom ring thumbscrew.
4. Loosen the focus ring thumbscrew.
5. Turn the focus ring to set the desired focus.
6. Tighten the focus ring thumbscrew.
-4 -
Zoom ring
Screw Focus screw

Camera Adjustment
90
90 -90
STANDARD
ROTATION
ROTA TI ON 180°
ROTATI ON 360°
A
B
C
 Horizontal angle adjustment – by turning the platform (illustrate as A & B)
to adjust the horizontal angle B (180 degrees): B (360 degrees)
 Vertical angle adjustment – turn the platforms (illustrated C) to adjust the
vertical angle: C (90 degrees).
Setting the DAY/NIGHT Camera switch level
The Day/Night Rugged Dome includes
a lens that provides a true-color picture
during daylight hours. The camera
includes a photocell that detects when
low-light levels occur and, with the
removal of a filter from the lens,
instigates infrared (IR) operation. IR
operation provides a true black and
white picture during low light
conditions.
To set the light level at which the camera switches between daylight and IR
mode
Day/Night
change
level
Photocell
-5 -

Mounting the housing
Inner plate
M4x12
pan-head
double-washer
Top gasket
Note: Feed the cables through the mounting surface, plates, and housing at the
appropriate time depending on whether you are using the flying lead and whether
the cable is external or internal to the mounting surface
-6 -

Surface-mounting the housing
Note: Feed the cables through the mounting surface, plates, and housing at
the appropriate time depending on whether you are using the flying lead
and whether the cable is external or internal to the mounting surface.
o prepare the mounting surface perform the following.
tion
2. position of the mounting holes.
its outline.
ack cable entry hole.
m
g holes.
the M4x20
To i he following.
e hinge.
n-head
3. e mounting slots on the inner plate with the
4. rews
T
1. Position the outer plate on the mounting surface at the installa
location.
Trace the
3. If you are using the back cable entry, trace
4. Drill the outlined mounting holes.
Ceiling panel
Outer plate
Inner plate
M4x20
pan-headdouble-washer
M4x12
pan-head
double-washer
Top gasket
Anchors
M4x20
5. If necessary, cut out the outlined b
To ount the outer plate, perform the following.
1. Install the provided mounting anchors in the mountin
2. Mount the plates to the anchors in the mounting surface using
truss-head tapping screws.
nstall the housing perform t
1. Let the housing cover drop down and rest on th
2. Attach the housing to the inner plate using the M4x12 pa
double-washer screws.
Line up the opening of th
M4x20 truss-head tapping screws holding the outer plate in place.
Rotate the housing clockwise to slide the mounting slots onto the sc
and secure the unit.
-7 -

Flush-mounting the housing
tes, and housing at the
and
o prep
is the side with the
2. P
ole.
i ng.
holes
he three M5x20
i
hinge.
n-head
ter plate.
Note: Feed the cables through the ceiling panel, pla
appropriate time depending on whether you are using the flying lead
whether the cable is external or internal to the mounting surface.
T are the ceiling panel perform the following
1. Remove the ceiling panel from the ceiling.
Note: Ensure that you trace the back of the outer plate: this
smaller diameter. If you trace the diameter of the front of the plate, your
mounting hole will be too large
osition the back of the outer plate on the ceiling panel at the installation
cation.
lo
3. Trace the outline of the outer plate onto the ceiling panel.
4. Use the traced outline as a guide to cut out the mounting h
To nstall the back and outer plates perform the followi
1. Insert the three M5x20 pan-head double-washer screws into the three
inside the back plate.
2. Set the back plate onto the back of the ceiling panel and center it over the
mounting hole.
3. Slide the outer plate into the mounting hole and back plate.
4. Line up the mounting holes and slots in the outer plate with t
pan-head double-washer screws in the back plate.
5. Slide the outer plate onto the screws in the back plate.
6. Rotate the outer plate to secure it to the back plate.
To nstall the housing perform the following.
e1. Let the housing cover drop down and rest on th
2. Attach the housing to the inner plate using the M4x12 pa
double-washer screws.
3. Slide the back of the housing and attached inner plate into the ou
4. Rotate the housing clockwise to slide the mounting slots on the inner plate
onto the screws in the back plate.
Back plate
Ceiling panel
Outer plate
Inner plate
M5x20
pan-headdouble-washer
M4x12
pan-head
double-washer
Top gasket
-8 -

Sp
Image de ” interline high sensitivity 1/3” interline transfer Exview
ecifications
vice: 1/3
SUPER HAD CCD HAD CCD
Signal system: PAL or NTSC standard
Picture elements
PAL: 752(H) x 582
N
2(H) x 582(V) HR
)
(V) HR PAL: 75
537(H) x 597(V) STD
TSC: 768(H) x 494(V) HR
537(H) x 505(V) STD
537(H) x 597(V) STD
(VNTSC: 768(H) x 494
537(H) X505 (V) STD
Scanning system: PAL: 625 linNTSC: 525 lines. es, 2:1 interlace
Sync system: DC 12V Internal or AC 24V Line-lock
Horizontal resolution: 480 es.)TV lines (Hi-res.) / 380 TV lines (Mid-r
Minimum illumination: 2 lux at F1.6 0.4 lux at F1.6
Day/Night change level adj 0.1 ~ 9 Lux
(Day/night Camera)
Day/Night change delay
time (Day/night Camera) 6 ~ 60 sec
Aperture correction: H aperture and V aperture
Gain: Max. Gain 30dB; Super Gain 36 dB
S/N ratio: Better than 48dB
AE Auto iris mode: 1/50(1/60) sec.
Auto iris lens: DC servo iris lens
Lens selection: 3.5 mm~8 mm ; 9 mm~22 mm (default)
ATW: 2500°K to 9500°K
Backlight compensation: Auto Detect; His ws weight BLCtogram plus windo
Video output signal: Composite: 1 V p-p at 75Ωload
Operating temperature: -10°C to 50°C
Power source: AC 24V /DC 12V (Non-polarity)
Power consumption: 2.9W(DC type)
3.4W(AC type)
Dimensions (f x H): 149(f) x 102(H) mm
-9 -