Columbia Products SANI-LAV 58F1 User manual

1
HANDS-FREE FLOOR MOUNTED WASH STATION
Operating Manual for Four-Person Hands-Free Floor Mounted Wash Station
Model 58F1
Columbia does not recommend use with harsh chemicals.
NSF/ANSI Standard 2 - Food Equipment and NSF/ANSI 372 low-lead.

2
COLUMBIA SPECIFICATIONS MODEL 58F1
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2013 Columbia Products
HANDS-FREE FLOOR MOUNTED WASH STATION
Tools Required
Tape Measure
Adjustable Wrench
Drill Motor and Drill Bits
Pipe Wrench
Level
Safety Glasses
Screw Drivers: 1 Phillips & 1 Standard
Pencil
Socket Wrench
Parts List
(1) Four-person floor mount wash station – Model 58F1
(1) Leg assembly set
(6) Washers and nuts for connection sink to leg assembly set
(4) Single foot pedal valves (bottom mount) with 12 nuts – Model 106L
(4) Swivel gooseneck spout with aerator – Model 2003L
(2) Strainer assembly with basket – Model 1010
(4) Connecting tubes for valve to spout connection – Model 1007L
(8) Fittings, brass, 0.375” male compression and 0.375” male NPT – Model 1008L
(4) Mixing check valve – Model 201L
Installation Instructions
Step 1
1. 2 and 3-Person models require leg assembly.
2. Place wash station sink on leg assembly and secure with hardware (provided).
3. Establish sink location.
4. Mark the floor where the four holes are at the base as shown in illustration A.
5. Drill holes as required for mounting hardware. (Hardware not included).
Step 2
1. Install spout assembly to the sink.
2. Install elbow fitting (provided) to the spout assembly.
3. Connect one side of the supply line (provided) to the spout assembly.
4. Install strainer assembly.
Step 3
1. Install mixing check valve and elbow fitting to valve.
2. Install foot pedal valves under the leg assembly cross bar if not mounted already.
3. Attach connecting tube from the spout to the foot pedal valve.
Step 4
1. Secure wash station to floor.
2. Connect waste line to strainer assembly.
3. Connect water supplies (hot and cold) to the mixing check valve.
Step 5
1. Remove aerator from the spout assembly and flush water line by pressing pedal for 30
seconds.
2. Check connections for leaks. Replace aerator onto the spout assembly.
3. Seal gap between bowl and leg assembly as shown in illustration B.
4. When mounting against wall, we recommend sealing top of backsplash to wall as shown in
illustration C.
Illustration A
Illustration B
Illustration C

3
COLUMBIA SPECIFICATIONS MODEL 58F1
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2013 Columbia Products
HANDS-FREE FLOOR MOUNTED WASH STATION
Valve Repair Instructions
Note: Valves are designed to be repaired without having to be disconnected from mount or plumbing.
1. Turn off water source. Do not remove valve from sink.
2. Remove pedal assembly using a 15/16” open end wrench or socket wrench. As shown in
illustration A.
3. Using a 1” deep socket wrench remove insert assembly parts as show in illustration B.
4. Replace with new repair kit as shown on illustration C.
5. Reinstall pedal assembly and turn water source on.
Trouble Shooting Guide
Problem Possible Cause To Diagnose Remedy
Water drips from spout
or valve stem assembly.
Flat washer on the
stem/plunger is worn.
To determine if the leak source is from the hot or cold side shut
cold water source off. See if water still leaks from the spout. If
leak continues then repair hot side if not repair cold side.
We recommend installing valve repair
kit.
Water leaks from the
front of the valve.
O-Rings on the
plunger are worn out.
Visually determine whether the cold or hot side is leaking. We recommend replacing threaded
insert, plunger assembly & spring.
See illustrations below.
Illustration A
Illustration B
Illustration C

4
COLUMBIA SPECIFICATIONS MODEL 58F1
1622 Browning Irvine, CA 92606-4809 Phone: [phone] Toll Free: 800.626.2117 Fax: [phone] www.columbiasinks.com email: [e-mail]
©2013 Columbia Products
HANDS-FREE FLOOR MOUNTED WASH STATION
10” (254mm)
45º
58 Floor
10.25”
(267 mm) 10.25” (267 mm)
80” (1524mm)
20” (508mm) 20” (508mm)
77” (1956mm)
20”
(508mm)
2” drain hole
16.5”
(407mm)
10”
(254mm)
8” (203mm)
8” (203mm)
.25” R
6mm
.25” R
6mm
1.5” (38mm)
2” (51mm)
1.5” (38mm)
2” drain holes,(1.5” strainer)
Hole Configurations
Front
Side
Top
6.75”
(171mm)
10”
(254mm)
.875” (22mm)
dia. holes (4)
11”
(280mm)
18”
(457mm)
11”
(280mm)
18”
(457mm)
22”
(559mm)
27” (686mm)
27” (686mm)
35” (889mm)
floor to rim
height 10.5” (267mm)
.5” dia. floor
mounting holes
1.5” (38mm)
leg thickness
.75” (19mm)
from edge of leg
to first hole
Leg Specifics
10.25”
(260mm)
2.75”
(70mm)
2.75” (70mm)
from back of leg
to wall
36.88” (397mm) 36.88” (397mm)
20” (508mm)
2” (51mm)
7.5” (191mm)