Columbia Weather Systems 10200-DECK2-B User manual

10200-DECK2-B Weather Station 1
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Columbia Weather Systems
Weather Station
10200-DECK2-B
with Hukseflux Solar Radiation Sensors
For Sunlight General Installations
User Manual
Version 1.02
Serial Number: _________________
Date Purchased: ________________
All specifications subject to change without notice.
Printed in U. S. A.
© Copyright 2012 Columbia Weather Systems, Inc. All Rights Reserved.

2 10200-DECK2-B Weather Station
________________________________________________________________________________________________________________
Columbia Weather Systems, Inc.

10200-DECK2-B Weather Station 3
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Important Notice: Shipping Damage
BEFORE YOU READ ANY FURTHER, please inspect all system components for obvious shipping damage.
The weather station is a high precision instrument and can be damaged by rough handling. Your unit was
packaged to minimize the possibility of damage in transit. Please save the shipping container for any future
shipment of your weather station.
In the event your order arrives in damaged condition, it is important that the following steps be taken immediately.
The title transfers automatically to you, the customer, once the material is entrusted to the transport company.
NOTE: DO NOT RETURN THE INSTRUMENT TO COLUMBIA WEATHER SYSTEMS until the following steps are
completed. Failure to follow this request will jeopardize your claim.
1. Open the container and inspect the contents. Do not throw away the container or any damaged parts. Try
to keep items in the same condition as originally received.
2. Notify the transport company immediately.
3. Request the transport company’s representative inspect the shipment personally.
4. After inspection, request a Return Materials Authorization (RMA) from Columbia Weather Systems by
calling [phone].
5. Return approved items to us at the following address:
Columbia Weather Systems, Inc.
2240 NE Griffin Oaks Street, Suite 100
Hillsboro, OR 97124
6. After a repair evaluation, an estimate of the cost of repair will be sent to you.

4 10200-DECK2-B Weather Station
________________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
ESD Protection
Electrostatic Discharge (ESD) can cause immediate or latent damage to electronic circuits. The Weather Station is
adequately protected against ESD for its intended use. However, it is possible to damage the product by delivering
electrostatic discharges when touching, removing, or inserting any objects inside the equipment housing.
To avoid delivering high static voltages yourself:
1. Handle ESD sensitive components on a properly grounded and protected ESD workbench. When this is
not possible, ground yourself with a wrist strap and a resistive connection cord to the equipment chassis
before touching the boards. When neither of the above is possible, at least touch a conductive part of the
equipment chassis with your other hand before touching the boards.
2. Always hold the boards by the edges and avoid touching the component contacts.

10200-DECK2-B Weather Station 5
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
System Enclosure:
The system enclosure includes the following:
AC power supply with 24VDC output
Weather MicroServer
RS-485 Terminal Strip
Two solar amplifiers
The system enclosure is weatherproof and includes hardware to mount the unit on a mast.

6 10200-DECK2-B Weather Station
________________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Weather MicroServer
The Weather MicroServer uses a small computer board that runs an embedded Linux operating system.
The MicroServer has 2GB flash memory for data logging and operation.
The MicroServer has two RS-232 COM ports and an Ethernet port
The MicroServer offers the following:
XML Weather Data
FTP weather data in XML or CSV format
Modbus/TCP, Modbus RTU (Serial RS-232), and Modbus ASCI interfaces
SNMP interface
Weather Underground interface
CWOP interface
Three months of data logging at 1-minute interval
Interface to optional visibility and solar radiation sensors
MicroServer Configuration
The MicroServer is set to a default IP address of 192.168.0.50.
To connect to the MicroServer using a computer, set the computer to a static IP address of 192.168.0.49.
Use an Internet browser to connect to the MicroServer over its IP address.
Log in information:
User name: admin
Password: admin

10200-DECK2-B Weather Station 7
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Installation
Installation Overview
Installing the 10-foot Tripod
Install the weatherproof enclosure to tripod
Installing the air temperature sensor with radiation shield
Installing the panel temperature sensor
Installing the solar radiation sensors
Connecting sensors to the MicroServer
Connecting to MicroServer to RS-485
System Diagram

8 10200-DECK2-B Weather Station
________________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Tripod and Tiedown Kit
The meteorological tripod is designed to provide up to 10 feet of stable, secure support for your meteorological
sensors.
Constructed from welded aluminum and clear anodized for appearance and longevity, the 15-pound tripod can
easily support up to 60 pounds of equipment. An optional tie-down kit allows for additional security in high-wind
areas.
To install, insert the legs into the main body and secure with stainless steel retainer pins. Extend the mast to the
desired height and insert another retainer pin. Install the guy wires to complete the set-up.

10200-DECK2-B Weather Station 9
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Tripod Parts List:
Item # Description Qty
1 Body/Mast Assembly 1
2 Legs 3
3 Retainer Pins 4
4 Guy Wire Ring with 1
3 Wires and Turnbuckles
5 Anchor Screw with Chain Not included in this configuration
6 Clamp with Strap 1
7 Retainer Pin 1

10 10200-DECK2-B Weather Station
________________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Installing the Air (Ambient) Temperature Sensor
The air temperature sensor is installed in the self-aspirating radiation shield.
The temperature radiation shield should be mounted on the pole facing the north.
Installing the panel temperature sensor
The panel temperature sensor can be attached to the solar panel using a 5-minute epoxy.
Use tie wraps to secure the cable to the panel frame.
Installing the solar radiation sensor
The solar radiation sensor can be installed on the mast using the hardware included to provide solar radiation
measurement.
Two types of brackets are provided: one for global radiation measurement, and the second for POA radiation
measurement.

10200-DECK2-B Weather Station 11
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Plane of Array Solar Radiation:
Install the solar sensor on the POA bracket using the provided screws, washers, and nuts. Use the two holes
marked in the photo below:
Install the bracket on the pole using the two sets of u-bots:
The POA solar sensor should be facing the south in order for the pole not to shadow the sensors.

12 10200-DECK2-B Weather Station
________________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Global Solar Radiation:
Remove the three top screws and discard.
Change the position of the U-bracket to allow for mounting on a vertical pole
Install the sensor on the bracket using the provided screws, washers, and nuts and mount the bracket on the pole

10200-DECK2-B Weather Station 13
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Make sure the sensor is level. If not, loosen the mounting screws and adjust the leveling screws to achieve level
installation.
Note:
Each Hukseflux LP02 solar radiation sensor comes with a unique sensitivity value. Therefore it is important that the
sensors are connected to the correct solar input (Solar 1 or Solar 2).
Each Hukseflux LP02 solar radiation sensor comes with a unique sensitivity value. Therefore it is important that the
sensors are connected to the correct solar input (Solar 1 or Solar 2).
If the solar sensor is replaced in the future, then the sensitivity/factor needs to be entered in the MicroServer
interface.
Connecting sensors to the MicroServer
Connect the panel temperature sensor to Channel 2.
Connect the air temperature sensor to Channel 3.

14 10200-DECK2-B Weather Station
________________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Connecting to MicroServer to RS-485
The Modbus RTU is set to 9600 baud rate, none parity with a Modbus address of 51.

10200-DECK2-B Weather Station 15
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Modbus Registers
Weather MicroServer with Modbus TCP/IP Slave Interface or Modbus/RTU over COM2 (RS-485)
32-Bit Registers
All data accessed via (read only) input registers [Modbus function code 3]
Data type Long = Signed 32 bit value
Data type Float = 32 bit floating point value
Measurement
Description
Starting
Modbus
Offset
Columbia
data type
Modbus
Address
OPC
data
type
umtLastMeasTime
Time of last measurement
1
posix time
30001
Long
umtTemp2
Panel/Cell Temperature
253
float
30253
Float
Panel/Cell Temperature time stamp
255
posix time
30255
Long
umtTemp3
Air (Ambient) Temperature
257
float
30257
Float
Air (Ambient) time stamp
259
posix time
30259
Long
umtSolarRadiation
Solar Radiation 1
265
float
30265
Float
Solar Radiation 1 time stamp
267
posix time
30267
Long
umtSolarRadiation_2
Solar Radiation 2
269
float
30269
Float
Solar Radiation 2 time stamp
271
posix time
30271
Long
Notes:
For each of the available measurements, the two registers immediately following the value contain the posix time
value of the time that value was last updated. For example: Panel/Cell temperature value is stored in registers 253
and 254. The last update timestamp is stored in registers 255 and 256 and is a 32-bit integer value.
The posix time values are 32-bit integers; all the values are Modbus input registers.

16 10200-DECK2-B Weather Station
________________________________________________________________________________________________________________
Columbia Weather Systems, Inc.

10200-DECK2-B Weather Station 17
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
USER SUPPORT INFORMATION
This section consists of the following items:
1. One-Year Limited Warranty: Please read this document carefully.
2. Return for Repair Procedure: This procedure is for your convenience in the event you must return your Weather
Station for repair or replacement. Follow the packing instructions carefully to protect your instrument in transit.
Limited Warranty
Columbia Weather Systems, Inc. (CWS), warrants the Weather Station to be free from defects in materials and/or
workmanship when operated in accordance with the manufacturer’s operating instructions, for one (1) years from
date of purchase, subject to the provisions contained herein. CWS warranty shall extend to the original purchaser
only and shall be limited to factory repair or replacement of defective parts.
EXCLUSIONS
Certain parts are not manufactured by CWS (i.e., certain purchased options, etc.) and are therefore not covered by
this warranty. These parts may be covered by warranties issued by their respective manufacturers and although
CWS will not warrant these parts, CWS will act as agent for the administration of any such independent warranties
during the term of this warranty. This warranty does not cover normal maintenance, damage resulting from
improper use or repair, or abuse by the operator. Damage caused by lightning or other electrical discharge is
specifically excluded. This warranty extends only to repair or replacement, and shall in no event extend to
consequential damages. In the event of operator repair or replacement, this warranty shall cover neither the
advisability of the repair undertaken, nor the sufficiency of the repair itself.
THIS DOCUMENT REFLECTS THE ENTIRE AND EXCLUSIVE UNDERSTANDING OF THE PARTIES, AND
EXCEPT AS OTHERWISE PROVIDED HEREIN, ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
PARTICULARLY THE WARRANTIES OF MERCHANT ABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE ARE EXCLUDED.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Return for Repair Procedure
1. In the event of defects or damage to your unit, first call the Service Department Monday through Friday,
8:30 am to 4:00 pm PST, [phone] to determine the advisability of factory repair. The Service
Department will issue an RMA number (Return Merchandise Authorization) to help us identify the package
when received. Please write that number on the outside of the box.
2. In the event factory service is required, return your Weather Station as follows:
A. Packing
 Wrap the Sensor Transmitter in a plastic bag first.
 Pack in original shipping carton or a sturdy oversized carton.
 Use plenty of packing material.
B. Include:
 A brief description of the problem with all known symptoms.
 Your telephone number.
 Your return street shipping address (UPS will not deliver to a P.O. box).
 Write the RMA number on the outside of the box.
C. Shipping
 Send freight prepaid (UPS recommended).

18 10200-DECK2-B Weather Station
________________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
 Insurance is recommended. (The factory can provide the current replacement value of the item
being shipped for insurance purposes.)
D. Send to:
Columbia Weather Systems, Inc.
2240 NE Griffin Oaks Street, Suite 100
Hillsboro, Oregon 97124
E. C.O.D. shipments will not be accepted.
3. If your unit is under warranty, after repair or replacement has been completed, it will be returned by a
carrier and method chosen by Columbia Weather, Inc. to any destination within the continental U.S.A. If
you desire some other specific form of conveyance or if you are located beyond these borders, then you
must bear the additional cost of return shipment.
4. If your unit is not under warranty, we will call you with an estimate of the charges. If approved, your
repaired unit will be returned after all charges, including parts, labor and return shipping and handling, have
been paid. If not approved, your unit will be returned as is via UPS COD for the amount of the UPS COD
freight charges.

10200-DECK2-B Weather Station 19
______________________________________________________________________________________________________________
Columbia Weather Systems, Inc.
Columbia Weather Systems, Inc.
2240 NE Griffin Oaks Street, Suite 100
Hillsboro, OR 97124-6463
Telephone
[phone]
Fax
[phone]
Web Site
http://www.columbiaweather.com
Email
[e-mail]
Version 1.02
Printed in U.S.A.