UP & UD Series
Installation and Operating Instructions
Limited Warranty:
Products of Comfort Home are warranted to the first user only to be free
of defects in material and workmanship for a period of 12 months from date
of installation, but no more than 18 months from date of manufacture.
Comfort Home's liability under this warranty shall be limited to repairing or
replacing at our election, without charge, FOB Comfort Home's distribution
center or authorized service agent. Comfort Home will not be liable for
any cost of removal, installation, transportation or any other charges that
may arise
in connection with warranty claim.
The warranty period commences on the date of original purchase of the
equipment. Proof of purchase and installation date, failure date, and
supporting installation data must be provided when claiming repairs
under
warranty.
This warranty is subject to due compliance by the original purchaser with
all directions and conditions set out in the installation and operating
instructions. Failure to comply with these instructions, damage or breakdown
caused by fair wear and tear, negligence, misuse, incorrect installation,
inappropriate chemicals or additives in the water, inadequate protection
against freezing, rain or other adverse weather conditions, corrosive or
abrasive water, lightning or high voltage spikes or through unauthorized
persons attempting repairs are not covered under warranty.
Comfort Home will not be liable for any incidental or consequential damages,
losses, or expenses, arising from installation, use, or any other causes.
There are no express or implied warranties, including merchantability
or fitness for a particular purpose, which extend beyond those
warranties described or referred to above.
Certain countries do not permit the exclusion or limitation of incidental
or consequential damages or the placing of limitations on the duration
of an implied warranty, therefore, the limitations or exclusions herein
may not apply. This warranty sets forth specific legal rights and
obligations, however, additional rights may exist, which may vary from
countries to countries.
Supersedes all previous publications.
Submersible Utility Pump
CCBUPUDE01
Pump runs
but does
not deliver
water.
●Check valve is installed backwards.
Arrow on valve should point in direction of flow.
●Discharge shut-off valve (if used) may be closed.
●Impeller or volute openings are fully or partially clogged.
Remove pump and clean.
●
Pump is air-locked. Start and stop several times by plugging and
unplugging cord. Check for clogged vent hole in pump case.
●Inlet holes in pump base are clogged. Remove pump and clean
the openings.
●
Vertical pumping distance is too high. Reduce distance or change
the discharge fittings of the pump.
Pump runs
and pumps
out sump,
but does
not stop.
●
Float is stuck in up position. Be sure float operates freely in
basin.
●Defective float switch. Replace with float switch.
●Defective vertical switch. Replace with vertical switch.
Pump runs
but delivers
only a small
amount of
water.
●
Pump is air-locked. Start and stop several times by plugging and
unplugging cord. Check for clogged vent hole in pump case.
●
Vertical pumping distance is too high. Reduce distance or change
the discharge fitting of the pump. Inlet holes in pump base are
clogged. Remove pump and clean the strainer and openings.
●Impeller or volute openings are fully or partially clogged.
Remove pump and clean.
●
Pump impeller is partially clogged with tar or paint, causing motor
to run slow and overload. Remove pump and clean.
Fuse blows
or circuit
breaker
trips when
pump starts.
Motor runs
for a short
time, then
stops.
●
Pump impeller is partially clogged with tar or paint, causing motor
to run slow and overload. Remove pump and clean.
●Motor stator may be defective.
●Fuse size or circuit breaker may be too small.
●Impeller or volute opening are fully or partially clogged.
Remove pump and clean.
●Inlet holes in pump base are clogged. Remove pump and clean
the openings.
●
Pump impeller is partially clogged with tar or paint, causing motor
to run slow and overload. Remove pump and clean.
●Motor stator may be defective.
●Impeller or volute openings are fully or partially clogged.
Remove pump and clean also clean the strainer if you had installed.
WEBSITE : www.everyfluid.com
R
Comfort Home
Water Solutions
Comfort Home
R
Comfort Home
