Component Playgrounds HL55 User manual

Installation Instructions
HL55
Required Crew: 2 Required but 4 Recommended
Concrete: 12-16, 80 lb. bags
Required Tools:
● Wheelbarrow
● Step Ladder (6’ or taller)
● Shovel
● Tape Measure
● Digging Bar or Pick
● Level
● Allen Wrench (Provided)
● Open end or Box Wrenches: 9/16”, ¾”
● Hammer or Mallet
● Ratchet Handle & Sockets: 9/16”, ¾”
● Marker Pen
● Drill: Cordless or electric, or impact driver
Component Playgrounds is concerned about the safety of your vision. It
is important that you choose to protect your vision by wearing proper
safety glasses during each and every phase of this construction
process.
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING
The HL55 can be installed as a one day project. The normal time required
to install the HL55 is about 3-6 hours for a two man crew. This time
requirement will vary dependent upon the composition of the soil and the
speed of the installers. Mix and pour the concrete as the last step.
*Before digging, please obey local laws by notifying your local
underground utilities marking organization*

Installation Instructions
1. Select an area in your yard that is reasonably level and meets the
space requirements for your equipment. Ground Space: 9’ x 22’ Play
Space: 13’ x 37’.
2. Using the measurements from the top view diagram, measure and
mark the position of the Swing Hangers and Ladders on both 9’ Top
Rails. Place the Horizontal Ladder on the ground in the desired
location with Top Rails in the correct position on the ground.
(Measure and adjust the Horizontal Ladder on the ground as
necessary to provide for the proper play space.)
3. Move 9’ Top Rails and set aside.
4. With the Horizontal Ladder in its proper position, mark the locations
for the holes where the two Upright Ladders will stand.
5. Move the Horizontal Ladder and dig the holes (see #1 hole sizes for
cementing).
6. Lay each Upright Ladder on the ground near the hole where it will
eventually stand. On the non-drilled Upright Ladder make a mark 15”
from the top of the Ladder onto each Ladder rail.
7. Move the Adjustable Sleeves to these marks and position them to
receive the Horizontal Ladder. This is accomplished turning them to
point at a 90 degree angle toward what will become the inside of the
structure. (The rungs are welded to what will become the outside of
the structure.)
8. On the Upright Ladder with holes drilled in the Rails (the Slide will
attach to this Ladder), repeat the process similarly as on the other
Ladder. However, the Adjustable Sleeves will be pointing to, and the
rungs will be welded onto what will become the inside of the
structure. This will make it easier to climb up the Upright Ladder to
the slide. Secure set screws.
9. Place the Upright Ladders onto their sides with the bottom of the pipe
just over the hole where it will eventually stand. Attach the Horizontal
Ladder to the Adjustable Sleeves of the Upright Ladders and secure
the set screws (see #3 Horizontal Ladder to Upright Ladder

assembly). Hint: Do not push Horizontal Ladder tight against the
Upright Ladders. Leave a ½” - 1” gap between the UPright Ladder
Rails and the Horizontal Ladder. This will allow for easier adjustment
of the Horizontal Ladder in the future.
10. Using two strong adults, stand the assembled Horizontal Ladder
set into the holes.
11. Install plugs into the ends of the Top Rails.
12. Slide Top Rails into Top Sleeve of the Upright Ladders (see #2
Ladder to Top Rail assembly). Secure set screws.
13. Assemble and attach Swing Hangers to Top Rail (see Swing
Hanger assembly sheet).
14. Attach swing chains, seats, trapeze bar and rings.
15. Measure the height of the Top Rails to ensure proper swing
height.
16. Level the swing set.
17. Attach the Slide onto the Ladder with holes drilled (see Slide
Assembly instruction sheet).
18. Mix concrete according to package directions and pour the
appropriate quantities into each hole.
19. Allow cement to cure for 3-5 days and enjoy your Component
Playground!

#1 Holes Sizes for Cementing in the Set

#2 Ladder to Top Rail Assembly
#3 Horizontal Ladder to Upright Ladder Assembly

1. Loosen and remove the two nyloc jam nuts.
2. Reassemble on to swing top rail. Tighten securely so that the hanger is
firmly attached in place and cannot slide or swivel along top rail.
3. Attach carabineer with chain through the ring.
Note: We recommend you check the pendulum in the swing hangers at
least every 6 months for normal wear.

Rocket Slide Mounting Instructions

Read Before Use
Congratulations! You have just purchased one of the finest pieces of playground equipment available.
Your family will enjoy many hours of fun with this fine equipment. Playground equipment can be most
enjoyable, but there are some dangers if not used properly. You should be aware of the following:
Equipment should be installed in a level area, free from obstructions, with enough space to allow for
adequate clearance in all directions when equipment is in maximum use.
Keep objects away from equipment that could interfere with persons using it or that could be hazardous.
Misuse or abuse of this playground equipment is dangerous and can cause serious injury.
This equipment should be inspected before each use and any worn, defective or missing parts should be
replaced.
Children should play on equipment only with adult supervision and should be duly warned of the potential
hazards in this type of equipment when used improperly. Children should be instructed as to proper
caution to take in its use.
Equipment should NOT be used when it is wet or icy.
Equipment should only be used in a well-lit area.
Do NOT use equipment when tired, under stress or emotionally upset.
Do NOT overcrowd.
Do NOT use equipment when under the influence of alcohol or drugs.
Do NOT attempt somersaults or gymnastic stunts on or using this equipment.
Know your own limitations and exercise caution at all times.
Do not jump off of equipment when dismounting. It is a dangerous practice to jump on or off equipment.
Do not attempt to use equipment for something other than the use for which it was designed and
intended, or in a manner other than that for which it was designed and intended.
While every attempt is made by Component Playgrounds to ensure the highest degree of
safety in all of our equipment, we cannot guarantee freedom from injury. The user
assumes all risk of injury due to use. All merchandise is sold on this condition, which no
representative of the company can waive or change.

Maintenance of your playground
We hope that you and your family will enjoy many hours of great family fun while using your
Component Playgrounds Products. We appreciate your business. Our goal is to provide safe,
durable and fun products using the best materials available. Your product should be mostly
maintenance free. However, you should consider the following suggestions with regard to the
up keep of your new swing set.
1. Chains and Connectors: The chains are coated with the highest quality bright zinc
coating and the highest quality polymer coatings available. However, over time the
zinc coating may become discolored or eventually have surface rust appear. The
polymer coating may also become discolored with time and may eventually crack. This
depends mostly upon environmental conditions and normally will not affect the
durability and safety of the product. However, these items should be inspected
regularly for excessive wear and should be replaced as necessary.
2. Swing Hangers: These items are coated with a high quality galvanizing. However,
swing hangers may become discolored or may eventually rust. Should this happen, a
touch up using a cold galvanizing compound followed by a coat of silver aluminum spray
paint will make them look new again. These items can be purchased in aerosol cans
(“spray paint”) at most hardware stores and at Component Playgrounds. The brass
bushings inside of the swing hanger are impregnated with lubricant and will not
generally require any further lubrication. However, these should be periodically
inspected for wear and replaced as necessary. Note: Twisting the chains while swinging
will put extra wear on the swing hanger parts. If your children enjoy this practice, please
inspect the swing hangers more frequently.
3. Tire Swing Knuckles (for sets with a tire swing): The tire swing knuckle arrives at
Component Playgrounds pre-lubricated from the manufacturer. However, it is good
practice to inspect the knuckle and be sure that there is adequate lubrication before it
is used for the first time. After that, the tire knuckles should be lubricated at least twice
annually to prevent excessive wear and the eventual failure of the tire swing knuckle.
4. Welds: The heat from the welding process will damage the galvanizing that is on the

pipe when it arrives to us from the manufacturer. This damage to the galvanizing is
restricted to the actual weld. When your equipment is built, Component Playgrounds
will repair this damage using a cold galvanizing compound spray along with a top coat
of silver aluminum. This is a time tested and durable process. However, when you are
inspecting your playground equipment, if you notice that some surface rust has
appeared on the welds, simply apply a fresh coat of the cold galvanizing compound
and the silver aluminum top coat to keep your structure looking new. (These spray
products
can be purchased in aerosol cans (“spray paint”) at most hardware stores and
at Component Playgrounds.)
5. Plastic Lumber Platforms: If you have purchased a structure which includes a
platform, the plastic lumber does not need to be finished or stained. It is 100%
maintenance free. However, you may need to occasionally hose it down to remove
dirt and other debris that may collect after many hours of use by happy children.
6. Vinyl Canopies: If you have purchased a structure which includes a vinyl canopy, this
product should be inspected occasionally for wear and will need to be replaced as
necessary. Depending upon your environmental conditions, the normal life
expectancy of the vinyl canopy is 3 – 5 years.
7. Swing Seats: These should be inspected at least twice annually and should be replaced
as necessary.
8. Slides: Slides should never be lifted at the bottom. Lifting the slide at the bottom will
almost always cause the slide to crack at the top where it has been attached to
the platform or bracket. Cracks and wear such as is caused by this practice are
easily identifiable and will not be covered under the product warranty.
Slides should be inspected at least annually to ensure that the sliding surface is in
good condition. Also inspect the side rails to be sure that the plastic has not been cut
or gouged in any manner which would present the risk of injury while sliding.
9. Fasteners: All fasteners should be periodically inspected to make certain that they are
tight and secure. Re-secure as
necessary.
*For Safety please inspect all moving parts on a regular basis. (At Least Yearly)
Especially paying attention to wear within the swing hanger.