Comtech EF Data CT-C4002DM User manual
USER MANUAL
SPECIFICATION
IR
VANDALPROOF CAMERA
CT-C4002DM
Notes:Before providing power for the camera,
please read this User Guide in detail!
* The specifications are subject to change without notice.
Model NO.
CT-C4002DM
Camera
Image Sensor
1/3" SONY
DSP
Enhanced "Eo-E"
Horizontal Resolution
700TV Lines
Eective Pixels
PAL: 570KP, 976(H)×582(V) NTSC: 480KP,
976(H)×494(V)
TV System
PAL/NTSC
Electronic Shutter Time
Auto: PAL 1/50-1/100, 000Sec; NTSC 1/60-1/100, 000Sec
Sync System
Internal
Usable Illumination
0.001Lux/F1.2
S/N Ratio
52dB
Gamma Correction
0.45
Scanning System
PAL: 625 Lines, 50 Field/Sec; NTSC: 525 Lines, 60 Field/Sec
Video Output
Composite Signal (1.0Vp-p, 75 )
Lens
Focus Length
2.8-12mm
Focus Control
Manual
Lens Type
Manual
Pixels
2M Pixels
Auto Iris Support
NO
Night Vision
Infrared LED
5X36PCS
Infrared Distance
30M
IR Status
Under 10 Lux By CDS
IR Power On
CDS Auto Control
Camera Features
Day/Night
Color/ B&W
OSD Menu Language
CN, EN, FR, DE, JP, ES, PT, RU
Wide Dynamic Range
DWDR
Backlight Compensation
YES
White Balance
AUTO
Gain Control
AUTO
Noise Reduction
2D NR
Privacy Masking
YES
Digital Zoom
NO
Picture Adjustment
YES
UTC Support
YES
General
Vandal proof Housing
YES IP 66
Lens Angle Adjustment
YES
Dual Voltage
NO
IR Cut Filter
NO
Heater
NO
Operation Temperature
-10 RH95% Max
Storage Temperature
-20 RH95% Max
Power Source
DC12V±10%, 700mA
Dimension
131 x 93(H)mm
Weight
800g
Approvals
CE,EN
INSTALLATION
1. Open the packet and select the location where you would like to install the camera.
Take the mounting bracket off the camera.
2. Slightly drill the supplied three screws into the three round holes on the mounting bracket and
rotate the bracket clockwise until the screws are wedged into the narrower chase.
Tighten the fixing screws to secure the mounting bracket to the ceiling.
3. Drill a hole in the middle circle and let the power and video line go through.
4. Mount the body onto the mounting bracket and rotate it until it clicks to secure.
Adjust the camera to the correct position and test the camera to make sure it is working properly.
TROUBLE/SOLUTION
1. No picture after providing power
• May be the power supply voltage abnormity, please
check the power supply voltage and pole whether
exactitude.
• Please check all the connecting cable and monitors
whether be connected correctly or not.
2. The picture level direction have flowing interference ripples
• May be caused by the power supply AC ripples, it need
filter the wave of the power supply.
•Check the monitor and peripheral equipments used.
3. The picture background color changes continuously
• The fluorescent lamp’s electromagnetic field cause color roll.
•This is proper phenomenon of the cameras.
• Reduce the fluorescent lamp numbers or increase the
distance between the camera and the fluorescent lamps
can improve it.
• Use power supply external sync. camera can solve it.
4. The picture smear too mass
• The power supply’s voltage unstable.
• Connecting cables not connect correctly or have high
impedance.
CONNECTION
1. DC12V Input Terminal
Connect the power terminal of the camera to a 12V DC regulated power supply.
Note: Please use the correct power adaptor, DC12V (regulated), to operate this unit.
The power tolerance of this unit is DC12V ± 10%. Over maximum DC 12V power input will damage this
unit.
2. Video Output Connector (VIDEO OUT)
Connect the camera video output and the monitor video input with 75Ωcoaxial cable.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected seperately at
the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do not dispose of these
products as unsorted municipal waste.
CE Mark
This apparatus is manufactured to comply with the radio interference.
The company does not warrant that this manual will be uninterrupted or error-free. We reserve the right to revise or remove
any content in this manual at any time.
CAUTION:
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.
Only operate this apparatus from the type of power source indicated on the label.
The company shall not be liable for any damages arising out of any improper use, even if we have been advised of the possibility of such damages.
RISK OF ELECTRIC SHOCK
CAUTION
