Contec FA-UNIT-F11BE User manual

Ver.1.01
FA-UNIT-F14BE 1
Wall-Mount / Desk-Top Chassis for SBCs
FA-UNIT-F11BE
*Specifications, color and design of the products are subject to
change without notice.
This product is a chassis used to mount a backplane and SBC
and configure a computer system in combination with
expansion boards and various drives.
A PICMG compliant, PCI bus or ISA bus backplane can be
mounted.
Equipped with 5-inch-drive bay x 2 and 3.5-inch drive bay x 2.
Equipped with a power switch, reset switch, and USB
connectors at the front.
Equipped with a built-in cooling fan. The dustproof filter and
cooling fan can be replaced externally. These fans can easily
be replaced externally, without removing the top cover.
A chassis fixing bracket is attached as standard.
Backplanes are sold separately. You need prepare a CONTEC
backplane corresponding to this product, separately. For more
details of the corresponding backplanes, see "Option".
When using a third-party's backplane, pay attention to the
positions of the backplane installation holes, installable size,
and power supply specifications of this product.
This product has a space that can contain two 5-inch drives
and two 3.5-inch drives. It also has a power ON/OFF switch,
power supply LED, HDD access LED, reset switch and two
USB connectors on the front surface of the case.
* Depending on the combination of the backplane, SBC and expansion board mounted on
this product, one of the three installable 3.5-inch drives may not be installed. For details,
contact our general information center.
General specifications
Item Specification
Number of user slots 9 full-size slot
+
2 half- size slot
Installable board (mm) Full-size : 340.5(L) x 122.0(H) (Max.)
Half-size : 220.0(L) x 122.0(H) (Max.)
Rack mountable EIA 19-inch rack mountable
Fan Inlet x 1
(Excluding power supply fan)
Drives 5-inch x 2
3.5-inch x 2
Number of slot holes 11
Installable Backplane
dimensions (mm)
246.4(W) x 264.2(D) (Max.)
BPM-1111, BPI-1111, BPC-1111
Dimensions (mm) 364(W) x 177(H) x 420(D) (Excluding raised parts)
Weight About 11kg (Excluding backplane, motherboard, drives, etc.)
Power supply specifications
Item Specification
Power capacity *1 +5V 25A -5V 0.3A
+3.3V 25A -12V 0.8A
+12V 15A +5VSB 2A
Overall maximum power
supply capacity
300W
AC Power Voltage *2 115VAC/230VAC(50/60Hz) (SW selection)
Input current 10A(115VAC)/5A(230VAC)
AC Outlet None
*1 Total of +5V and +3V shall not exceed the power of 200W.
*2 Input voltage range for AC power supply : 90 - 132VAC / 180 - 250VAC
Environmental specification
Item Specification
Operating temperature 0 - 50°C
Operating humidity 10 - 80%RH(No condensation)
Storage temperature 0 - 60°C
Storage humidity 10 - 90%RH(No condensation)
Vibration resistance 10 - 57Hz/semi-amplitude 0.075mm 57 - 150Hz/1.0G
Impact resistance 10G, half-sine shock for 11 ms
Floating dust particles Not to be excessive
Corrosive gases None
* The values in the above are constrained with the boards or the components such as
drives installed inside the product, so the figures do not necessarily represent the
tolerances for every operating condition.
SpecificationFeatures
Configuration

Ver.1.01
FA-UNIT-F14BE 2
Dimensions of installable board (Max.)
340.5 [220.0](L)
122.0(H)
[mm][ ] is a alf size case.
CAUTION
The internal power supply and cooling fan, fan filter are
consumables, requiring replacement after use for a certain
period of time.
Although the standards are given below, their lives may be
shortened depending on the operating environment. The
life span is likely especially to become short extremely in the
place which takes influence of trash, metallic powder, the
place which is much dust or oil, corrosive gas.
Power supply
: About 5 years (25°C, 60%, official environment)
Cooling Fan
: About 5 years (25°C, 60%, official environment)
Fan filter
: About 1 year (25°C, 60%, official environment)
Installable backplanes
BPI-1111 PICMG Backplane with 10-Slots
(PICMG x 2, PCI x 4, ISA x 4)
BPM-1111 PICMG Backplane with 11-Slots
(PICMG x 2, PCI x 8, ISA x 1)
BPC-1111 PCI Backplane with 10-Slots(PCI x 10)
Other
FA-CLAMP-01 Clamp for PCI/ISA board (5 pcs)
* Check the CONTEC’s Web site for more information on these options.
POW300X 300W ATX Power Supply
FAN1225S Fan 120 x 25 with Sensor
FLT121 Fan Filter (127 x 127)
Chassis [FA-UNIT-F11BE]…1
Power cable…1
Rubber pads…4
Screws (for Rubber pads) (M4 x 8)…6
Screws (used for expansion bay fixing
and board installation) (M3 x 6)…32
Screws (for HDD) (#6-32UNC x 5)…8
Hexagon spacer…13
Plastic Spacers…5
Bracket for wall-mounted…2
Slot cover…11
User’s Manual…1
< Horizontally placed >
8-φ5
420
RESET
177
364
10
380
396
8080 160
130 130
15
R4.5
R2.5
[mm]
< Vertically placed >
RESET
8-φ5
177
420
36410
193 209
80 80160
130130
[mm]
15
R2.5
R4.5
Option
Packing List
Available Replaceable Parts for
Maintenance
Dimensions

Ver.1.01
FA-UNIT-F14BE 3
Positions of backplane installation holes
219.16
264.16
153.252 25.4
211.63
3.81
175.26
139.62
15.16
R3.25
R2
10
12.7
91.44
137.16
208
15.24
139.7
45.26228.9
18.38
7.62
176.53
212.09
20.62
15.875
30.48
76.2
213.36
233.68
246.38
116.88
179.54
[mm]
Max.
Max.
If a backplane whose shaded area is not cut off is installed,
then a 3.5-inch or 5-inch drive may not be installed properly
depending on the height of the installed parts, etc.
To prevent a temperature rise, install this chassis at a distance
of at least 50mm from obstacles such as walls.
50
Front Side View Rear Side View
[mm]
50 50
50
50
Front Side View Rear Side View
Power Supply
This product has built-in power supply units. The backplane
power supply connector and HDD and FDD power supply
connectors are provided. Connecting these connectors
enables the backplane, HDD and FDD to operate.
Backplane power supply connectors
It connects it with Backplane
or the motherboard
Pin No. Function Pin No. Function
1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 COM 13 COM
4 +5V 14 ON/OFF
5 COM 15 COM
6 +5V 16 COM
7 COM 17 COM
8 P.G 18 -5V
9 +5VS 19 +5V
10 +12V 20 +5V
HDD/FDD power supply connectors
1. 12V
2. GND
3. GND
4. +5V
YELLOW
BLACK
BLACK
RED
To HDD or CD-ROM
1. 12V
2. GND
3. GND
4. +5V
YELLOW
BLACK
BLACK
RED
To 3.5inch FDD
Installation conditions
Connectors