Convoy Performance Series Quick start guide

Convoy Technologies 6409 Highview Dr | Fort Wayne, IN 46818 | Ph [phone]
Owner’s / Installaon Manual
W1000 KIT
W1000RX RECEIVER
W1000TX TRANSMITTER
Please read this manual thoroughly before operang the unit, and keep it for further reference.

Convoy Technologies 6409 Highview Dr | Fort Wayne, IN 46818 | Ph [phone]
Owner’s / Installaon Manual
Performance Series
W1000 KIT
PRECAUTIONS
1. Precauons
Storage and keeping
Do not expose the W1000 to excessive heat or cold. The storage temperature of this device is -30 ~+75 C, and the oper
ang temperature is -20 ~+60 C. The Humidity is Rh90%.
Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar place.
Never use this device in environments with excessive moisture, dust or smoke.
Avoid dropping or striking this device.
Never puncture, scratch or use abrasive cleaning materials on this device.
The W1000 is not designed to be waterproof.
Operang Precauons
Make sure all cables are connected properly observe polarity. Improer cable connecons may damage the monitor. Re
move the power cable connecons when you do not intend to use the unit.

Convoy Technologies 6409 Highview Dr | Fort Wayne, IN 46818 | Ph [phone]
1. Precauons
Maintenance
1. Remove all the cable connecons from the W1000 before cleaning the unit.
2. Use a mild household detergent and clean the unit with a slightly damp, so cloth. Never use strong solvents such as thin-
ner or benzene, as they might damage the nish of the device.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s en-
closure that may be of sucient magnitude to constute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operang and maintenance (servcing) instruc-
ons in the literature accompanying the appliance.
This symbol is intended to alert the user not to waste electrical and electronic equipment.
CAUTION
You are cauoned that any changes or modicaons not expressly approved in this manual could void your warran-
tee and necessitate expensive repairs.
Declaraon of conformity
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condi-
ons: This device may not cause harmful interference. This device must accept any interference
received, including interference that may cause under desired operaon.
Owner’s / Installaon Manual
Performance Series
W1000 KIT
PRECAUTIONS

Convoy Technologies 6409 Highview Dr | Fort Wayne, IN 46818 | Ph [phone]
Owner’s / Installaon Manual
Performance Series
W1000 KIT
Mounng the Transmier
1) Select a locaon allowing space between W1000 and walls, cabinets, or other objects to allow adequate space around it.
Avoid enclosed spaces, areas with bundled cable or metal panels which may block recepon.
2) Never use this device in environments with excessive moisture, dust or smoke. Do not place cables where they may be
pinched or stepped on. W1000 is not designed to be waterproof.
3) The device may be powered by a 12 or 24 volt automove baery or vehicle electrical system, fuse value is 3A.
4) Make sure all cables are connected properly, observe polarity. Improper cable connecons may damage the W1000. Remove
the power cable connecons when you do not intend to use the unit.
Installaon Notes:
• Ensure unit has power and ground, and camera is connected properly
• LED light status:
• (ON = POWER ON & CONNECTED)
• (FLASHING = PAIRING MODE)
• (OFF = POWER OFF OR DISCONNECTED)
• Pairing: Hold the center pairing buon down on the transmier ll LED light is constantly ashing, then release
• Hold the pairing buon down on the receiver ll LED light is constantly ashing, then release
• When connecon is made, LED light on both W1000TX and W1000RX will be constant
W1000TX Harness:
• Red and Black—Power (12-24VDC) and Ground
• Camera input cable

Convoy Technologies 6409 Highview Dr | Fort Wayne, IN 46818 | Ph [phone]
Owner’s / Installaon Manual
W1000 KIT Operaon
Installing and using the W1000RX Receiver
The W1000RX receives it’s power from the monitor it is connect-
ed to.
• Connect the W1000RX camera cable to the monitor
• Turn the monitor on to power the W1000RX
• Push and hold the red pairing buon ll the LED ashes con-
stantly and release
• Push and hold the red pairing buon on the W1000TX trans-
mier ll the LED ashes constantly and release
• LED on both will stay on when connected
The W1000RX will pair directly with Convoy C1300RF camera, or TrailerCam.
• On the C1300RF, push the “B” buon repeatedly ll the 4 green LED ‘s are all o, then
push and hold the “B” buon for 6 seconds and release. The camera is now in pairing
mode, you have 50sec to pair with the W1000RX
• On the W1000RX, Push and hold the red pairing buon ll the LED ashes constantly and
release.
• Once paired the LED will be on constantly.
W1000KIT (consists of receiver and transmier)
 2.4GHz Wireless Transmier and Receiver
 FHSS channel hopping sequence based on an
algorithm generated by the receiver
 Zero Latency, Zero RF/Engine/Electronic Inter-
ference
W1000TX Transmier
 Transmier will pair with a Convoy Technologies
Wireless Monitor or Receiver, Connect any
wired Convoy camera
W1000RX Receiver
 Receiver will pair with any Convoy Technologies
Wireless Camera or Transmier, up to 100