Coolzone CZ55510 User manual

INSTALLATION AND OPERATING INSTRUCTIONS
50cm Double Cavity Electric Cooker
CZ55510
CZ55512
The product may differ from the one illustrated but the installation and operation procedure remains the same

Contents
Introduction 3
Unpacking 3
Before installation 3
Location 4
Electricity supply 5
Safety chain anchors 5
Electrical connection 6
Levelling the cooker 6
Securing the safety chains 7
Preparation 7
Safety notes 8
Fire safety 8
Cooker controls 9
Using the hob 9
Using the grill and top oven 10
Using the bottom oven 11
Care of the cooker 11
Cleaning the cooker 12
Cleaning the glass doors 12
Changing the oven lamps 13
For best cooking results 14
Troubleshooting guide 15
Safe cooker disposal Back page
Customer Helpline Back page
Specification Back page

3
Introduction
Thank-you for choosing this quality appliance. It has been designed to provide trouble-free service provided
it is installed and maintained correctly.This cooker is for domestic use only.
Please read these instructions carefully before installing or using your appliance. It is advisable to keep
your purchase and installation receipts with these instructions in a safe place for future reference. Included
is some important safety information, guidelines and recommendations to enable you to safely use your
cooker.
This appliance has been tested and certified to meet all applicable UK electrical and safety standards.
This appliance must only be installed and repaired by a qualified electrician from an authorised service
dealer. If it is not repaired properly you could be putting yourself and others in danger. It will also invalidate
the guarantee.
If you have any questions or need assistance please telephone the Helpline on 0844 871 0011.
When contacting the Helpline please have model number to hand.The model number is shown on the data
label which is visible by opening the oven door.
Unpacking
Carefully remove all the packaging and lift out the cooker and accessories.
Open the oven and remove any tape or packing material used for transit.
Check the appliance for any damage. If it has been damaged do not use it and contact the retailer from
whom the appliance was bought.
Retain the packaging until the cooker has been installed, removing it from the area of installation and
keeping it out of the reach of children.
Dispose of all the packaging in accordance with your local authority guidelines as well as any old appliance
that is being replaced – see “Safe cooker disposal” section.
Before installation
Before any installation work can be carried out a number of requirements must be met.
Make sure that you or your installer are familiar with all the relevant building and fire regulation
requirements before choosing the location of your appliance.
This appliance must be installed in accordance with the instructions to validate the guarantee.
Refer to the “Location” section for minimum clearances and safe placement of your cooker.

4
Location
Position of the cooker
The position of the cooker should ensure free access to all controls.
Avoid installing the cooker next to a fridge, freezer or boiler.
Safety Requirements
Ensure that the surrounding material is heat resistant and non-combustible.
The electricity supply must be routed near to the installation.
There must not be any plugs, wires or sockets in the wall directly above or behind the cooker top.
Clearance space
Certain minimum clearances must be allowed for when planning the unit’s location (Figure 1):
The cooker should be installed into a space at least 550mm wide.
There should be an open space above the hob to allow kitchen odours to disperse. A cooker hood may be
installed to either absorb or extract the odours.The distance between the hob and the hood must not be
less than 650mm (Figure 1).
Leave adequate clearance between the cooker top and adjacent tall cupboards (no less than 150mm.)
Figure 1 - minimum clearances
550 MIN
45A SWITCH

5
Electricity supply
Once a satisfactory location has been established, the electrical supply to the appliance must be arranged.
The mains voltage must correspond to that which is specified on the data plate.
The supply should be from a 45 amp fused spur, with an isolator switch installed above the work surface
and to one side of the unit in case of an emergency.The isolator switch must have working contacts
separated by 3mm.
This installation must be carried out in accordance with current I.E.E Wiring Regulations and Building
Regulations (Part P).
The mains supply cable from the isolator to the unit must be rated for the maximum power consumed by
the unit (also specified on the data plate).
The supply cable must be long enough to allow for servicing the appliance.
The supply cable must be routed away from hot surfaces.
Safety chain anchors
In order to eliminate the risk of the cooker falling forward, two chains have been installed at the rear of the
cooker. Before use, these will need to be fastened securely to the wall behind the appliance with the
anchor brackets supplied. (Figure 2):
1. Decide on a suitable wall location for the chain anchors, directly behind each cooker chain, at a height
of 830mm from floor level.The distance between the two brackets should be 355mm, measured from
the centre of each bracket. (Figure 2).
2. Hold the chain anchor up to the wall where it will be required, and mark the fixing holes. (Figure 2).
3. Drill the fixing holes and fix the chain anchors to the wall using the screws provided and suitable wall
plugs for the type of wall being fixed to.
4. Leave the chains unattached until the installation process has been completed.
Figure 2 - fixing an anchor bracket
830mm
TO FLOOR
355mm BETWEEN BRACKETS
SCREWS
ANCHOR
BRACKET
WALL
PLUGS
FIXING
HOLES

Levelling the cooker
The cooker is equipped with adjustable feet designed for levelling the cooker
and for adjusting the upper edge of the cooker to furniture level. (Figure 4).
1. Move the cooker into its final position.
2. If the upper edge of the cooker is not at the same height as adjoining units,
use the adjustable feet to raise or lower the unit to the required height.
3. If the cooker is not level or is unstable due to an uneven floor surface, use
the adjustable feet to adjust each corner until the cooker is level. Figure 4 – adjustable foot
6
The appliance must be properly connected to the mains supply by a qualified electrician according
to current safety regulations.
This appliance must be earthed.
1. Lift up the cover (Figure 3).
2. Loosen the cable clamp (Figure 3).
3. Connect the mains supply cable to the terminal block on the cooker using the following colour code
(Figure 3):
• The yellow/green wire should be connected to the earth terminal identified E.
• The blue or black wire should be connected to either of the neutral terminals, marked 4 and 5.
• The brown or red wire should be connected to one of the live terminals, marked 1, 2 and 3.
Secure the cable clamp. Check the cable terminals for tightness and ensure that the terminal links are in
place, then close the cover over the terminal block.
Figure 3 – electrical connections
LIVE
TERMINAL
COVER
NEUTRAL
TERMINAL
EARTH
TERMINAL
CABLE
CLAMP
Electrical connection

7
7
Securing the safety chains
Before securing the safety chains, check that you have completed the installation process and that all
connections have been made successfully and that the cooker is in its final operating position.
Fix the security chains to their anchor brackets:
1. Loosen the hex nut at the unattached end of the safety chain, until it is flush with the screw end. Do not
remove it completely. (Figure 5).
2. Insert the screwhead into the top hole of the anchor bracket by tilting it sideways so that it is at an
angle to the top hole when it is inserted. (Figure 6).
3. When the screw head is fully engaged in the bracket, tilt it upwards so that it is straight, and tighten the
hex nut to secure the end chain link into position.
Preparation
1. Ensure that the safety chains on the rear of the cooker is attached to its anchor on the wall behind.
2. Remove the remnants of any stickers, glue and adhesive tape from all surfaces of the cooker and the
hotplates, with warm water and washing-up liquid.
3. Dry the inside and outside surfaces of the cooker with a soft lint-free cloth.
4. Turn the grill to a moderate heat (page 10) for a few minutes to burn off any dust and manufacturing
residues.
5. Repeat the above process with the oven.
6. When using for the first time, turn on the hotplates, one at a time, and set the temperature selector
knob to position '3'. Leave them on for about 5 minutes.
When using for the first time the oven may smell for a short time while burning off residues.
Figure 5 – loosening the hex nut
Figure 6 – securing the cooker
HEX
NUT
TOP
HOLE
ANCHOR
BRACKET

8

• Never leave children unsupervised where the
cooker is installed as the appliance will get hot
during and after use.
• Never allow anyone to sit or stand on any part
of the cooker or surrounding work surface.
• Never heat up unopened food containers as
pressure can build up causing them to burst.
• Never store chemicals, food stuffs or
pressurised containers in cabinets above or
next to the cooker.
• Never use the cooker as a room heater.
• Never dry clothes or place other items on the
oven door.
• Never place flammable or plastic items on or
near the hob
• Never line any part of the oven cavity with
aluminium foil.
• Never lift the cooker using the oven door
handle.
• Make sure you understand what the cooker
controls do before using the oven.
• Always turn the cooker controls to the OFF
position when it is not in use.
• Before removing cooked food from the oven
open the door carefully to allow any heat to
disperse.
• Use dry oven gloves when removing items from
the oven.
• Be careful when operating the cooker and take
care to avoid touching hot surfaces inside the
oven and grill, and hotplates on the hob.
• Ensure that the cables of other household
appliances used near the cooker are away from
its hot elements. Ensure also that the cables
are not trapped by the oven door.
• Keep the oven door closed when the oven is
not in use.
• Keep the cooker clean as a build up of grease
or fat from cooking can cause a fire.
• Allow the cooker to cool before cleaning.
• Keep any ventilation holes clear of obstructions.
Safety notes

Fire safety
Never fill a deep fat frying pan more than 1/3 full of oil
Do not leave unattended while cooking!
In the event of a cooking pan fire:
1. Turn off the hotplate.
2. Cover the pan with a fire blanket or damp cloth.
3. Leave the pan to cool for at least an hour before you try to move it.
Never use a fire extinguisher to put out a pan fire (the force of the extinguisher could tip the pan over.)
Never use water to put out oil or fat pan fires.



9
Cooker controls
Before using your cooker for the first time:
Read the operating and safety instructions thoroughly.
If you have not already done so, follow the steps in the “Preparation” section on page 7 so that the cooker
is ready for use.
Familiarise yourself with the controls (Figure 7).
FRONT LEFT
HOTPLATE
BOTTOM OVEN
TEMPERATURE
CONTROL
TOP OVEN
TEMPERATURE
CONTROL
BACK LEFT
HOTPLATE
HOTPLATE ON
INDICATOR
TEMPERATURE
INDICATOR TEMPERATURE
INDICATOR
FRONT RIGHT
HOTPLATE
BACK RIGHT
HOTPLATE
Figure 7 – controls
Figure 8
4
3
21
4
1
3
2
Using the hob
Before using your hob for the first time:
Read the operating and safety instructions thoroughly.
If you have not already done so, follow the steps in the “Preparation” section on page 7 to burn off the
protective film covering the hotplates.
Before switching on a hotplate, make sure that the selector knob you are using corresponds to the hotplate
you wish to switch on (Figure 8).
WARNING: If any of the hotplates become cracked, disconnect the appliance from the mains supply
and do not use until repaired by a qualified technician.

PLEASE NOTE: It is important to close the oven door when using the grill.
Use this function for grilling or top oven heat which is suitable for browning food.
Move the shelf to the first or second position from the top.
Turn the temperature control between 75°C and MAX and preheat the element for five minutes (Figure 10).
Place the food in the middle of the grill pan and position the pan so the food is near but not touching the
top element.
Do not line the grill pan with aluminium foil or wrap food items with foil before placing under the grill.
Aluminium foil has a high reflectivity which can damage grill elements.
When fitting the handle, hook the handle over the edge of the grill pan and through the wire rack at a
central point along the grill pan edge, (Figure 11). Lower the handle fully down to fit.
10
The hotplates
The hotplate power is regulated with a 3 position temperature selector knob.The
control allows for the efficient transfer of heat to the cooking pan (Figure 9).
The selector knob can be turned in both directions:
• Anti-clockwise to increase heat
• Clockwise to decrease heat
There are numbers Gto 3 marked on the knobs (Figure 9).These numbers
correspond to the heat setting of the hotplate.
• 3 is the highest setting
•Gis OFF.
Using the grill and top oven
Figure 9
EDGE
HANDLE
WIRE RACK
Figure 11 - fitting the handle
Figure 10 - grill and top oven temperature control

1111
The temperature control determines the temperature inside the oven during cooking. Turn the control knob
clockwise to align the cooking temperature with the marker on the control panel. During cooking the
thermostat will maintain the set temperature (Figure 12).
The temperature can be set between 75°C and MAX.
PLEASE NOTE: It is recommended to preheat the oven for a few minutes or wait until the
temperature indicator goes off before placing food in the oven for cooking.
Be careful when using aluminium foil. Do not cover the sides of the oven, the shelf or oven interior. If
wrapping food in foil the cooking time may increase.
Temperature Control
Figure 12 - bottom oven temperature control
Using the bottom oven
Care of the cooker
Before removing a pan from a hotplate, reduce the heat or turn the hotplate off completely.
Ensure that the oven seal is always clean and free of debris.
Clean the cooker regularly to maintain its working condition and aesthetic appearance.
Do not steam pressure clean the oven.
Hotplates
Never turn the hotplate on before placing a pan on it (except when first used).
Never sprinkle cold water onto a heated hotplate.
Do not allow spills to be burnt onto the hotplate since baked stains are very difficult to remove.
Keep the hotplates clean. A dirty hotplate does not transfer heat efficiently.
Avoid placing wet pans on the hotplates.
Never use the hotplates for preparing foods wrapped in aluminium foil or in plastic pans, or place any
plastic trays etc. on the hotplates.

12
Cleaning the cooker
WARNING:The cooker must be allowed to cool down and be switched off at the mains electricity
supply before cleaning.
Clean the hotplates and the inside of the cooker after each spillage to remove cooking residues and dirt.
Hotplates should always be kept clean and dry to ensure proper performance.
When cleaning the cooker, do not use harsh abrasives, caustic cleaners or sharp objects.
Take particular care when cleaning the knobs, control panel, and any stainless steel parts, using soft
cleaners which do not contain abrasives.
All stainless steel parts should be cleaned with a non-abrasive cleaning liquid on a soft cloth.
Clean the hotplates with a damp sponge and then dry them by turning them on for a few seconds.To
maintain their appearance, apply a commercially available grease intended for hotplates.
The hotplate trim rings can be cleaned with products intended for stainless steel.The rings can become
yellowed as a result of heating.This is normal.
If a hotplate is to be out of use for a long time, apply the special grease periodically.
Cleaning the glass doors
Clean the glass part of the doors with hot water and a soft cloth.Wipe the rubber seals with a soft cloth
taking care not to damage them.

13
Changing the oven lamps
Wait for the oven to cool.
Unscrew and remove the diffuser. Unscrew the lamp from the lampholder. Replace lamp and diffuser
(Figure 13).
The replacement lamp must be of the same type, voltage and wattage (15W SES 300°C).
LAMP LAMPHOLDER
DIFFUSER
Figure 13 - changing the lamp

14
For best cooking results
For best results and good use of energy:


• Use good quality cooking pans with thick flat
bases.This gives the most efficient energy
transfer from the hotplate
• Use pans of the correct diameter. The base
should be about the same size as the hotplate
• Use pans which are large enough for the amount
of food being cooked to ensure that they do not
boil over and cause unnecessary cleaning.
• Use a correctly fitting lid when boiling or stewing
to contain heat and improve boiling times.
• Never use recessed or ridged base pans.This
wastes energy and gives a longer cooking time
• If the pan base is too small for the hotplate,
energy is wasted
• Do not place lids on the hotplates.
• Do not heat an empty pan on the hotplates, as
this will damage and discolour the cooking
surface at the bottom of the pan.
• Do not use wet pans on the hotplates
Oven
Grill
• For even cooking, ensure that the grill pan is
positioned centrally below the grill element. • To avoid fat splattering onto the oven interior,
ensure that the grill pan is not lined with foil and
the grill setting is not too high.
• Ensure that the oven shelf is level.This will
ensure even rising of cakes and cooking of food.
• To avoid under/overcooking, reduce or increase
cooking times and temperatures to suit personal
taste.
• Do not use pans greater than 52mm (2¼”) in
height for roasting.
Hob

15
If you are experiencing problems with your cooker, check the following problems and solutions below before
contacting the Helpline.
Troubleshooting guide
Problem Solution
Slight odour or small amount of smoke when using
the cooker for the first time. This is normal and should cease after a short
period.
Cooker does not work. Check that the power supply switch is ON.
Oven temperature seems too high or too low. Check that the temperature has been set in
accordance correctly. It may be necessary to
increase or decrease the recommended
temperature by 10°C.
Hotplates are slow to boil or will not simmer. Check that your pans conform to the
recommendations in these instructions.
Grilling is uneven. Check that the grill pan has been correctly
positioned.
Oven does not cook evenly. Check the temperature and shelf positions.
Check that the cooking containers used in the oven
allow sufficient air flow around them.
Marks appearing on hotplates. The hob surround can be cleaned with warm soapy
water and a cream cleaner.The sealed hotplates
should be cleaned regularly (please refer to the
care and cleaning section for more information).
Condensation on the wall at the rear of the cooker. Steam and/or condensation may appear from the
vent at the rear of the appliance when cooking food
with high water content.This is normal and any
excess should be wiped away.

Customer Service, Unit B1, Senator Point, South Boundary Road,
Knowsley, LIVERPOOL L33 7RS
HELPLINE TEL: [phone]
Monday to Friday (8.30am to 5pm)
We continuously try to improve our products for the benefit of our customers.
For this reason we reserve the right to make changes to any product at any time, without notice.
Instructions ref 26909/240108 © 2008
Safe cooker disposal
Customer Helpline
To help the environment, Local authority instructions should be followed for the disposal of your product.
This appliance/fitting is marked according to the European directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help pre-
vent potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product.
The symbol on the product, or on the documents accompanying the product, the Crossed Out Wheelie Bin
symbol, indicates that this appliance/fitting may not be treated as household waste. Instead it shall be hand-
ed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal
must be carried out in accordance with local environmental regulations for waste disposal. For more detailed
information about treatment, recovery and recycling of this product, please contact your local authority, your
household waste disposal service or the retailer where you purchased the product.
For help and assistance regarding your oven telephone [phone].
Specification
Power supply: 230V~50Hz.
Gross weight (kg): 49
External dimensions (cm) 50 width; 60 depth; 90 height
Oven capacity (litres): 48
Total wattage (W): 9000
Energy rating: A