Craftmade Cortana CR52 User manual

Installation Instructions
Instrucciones de instalación
Instructions d’installation
CR52
Cortana Ceiling Fan

1Read and Save ese Safety Precautions
1. Turn off electricity at main switch before wiring or servicing fan in order to avoid
possible electrical shock.
2. All wiring must be in accordance with the National Electric Code (ANSI/NFPA70-1999) and local
electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. After making the wire connections, the wires should be spread apart with the grounded
conductor and the equipment-grounding conductor on the one side of the outlet box
and the ungrounded conductor on the other side of the outlet box.
4. e splices after being made should be turned upward and pushed carefully up into the outlet box.
5. Conductor of a fan identified as grounded conductor to be connected to grounded conductor of power
supply, conductor of a fan identified as ungrounded conductor to be connected to an ungrounded
conductor of power supply, conductor of fan identified for equipment grounding to be connected
to an equipment-grounding conductor.
6. Fan should not be mounted in an area where it might get wet.
7. WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked
"Acceptable for Fan Support" and use mounting screws provide with the outlet box.
e outlet box and its support must be able to support the moving weight of the fan (at least 35lbs)
8. For safety and best operating results, we recommend that you have a qualified
electrician assemble and install your fan.
9. WARNING: To reduce the risk of fire or electric shock, use this fan only with solid state speed control
device provided.
10. Wall switch, model UC9787TB, the switch has been investigated and found acceptable for use as a
fan speed control.
11. WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing
the brackets, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
12. Weight: e weight of the complete fan, incuding assembly hardware is 20 lbs.
Trouble Shooting
Problem A: Fan Will not Start
Remedies:
1. Check fuse or circuit breaker and replace if necessary
2. Turn off electrical power and check all wire connectors.
3. Check on/off TCS and wall control selector switch. See operation instructions.
Problem B: Fan is Excessively Noisy
Remedies:
1. Check that all screws in fan assembly are tight and properly seated.
2. Check to make sure mounting bracket is installed properly.
3. Check to make sure light kit and glass are installed properly and tight.
4. If wall control is used, insure the wall control is not a transformer or a variable speed type.
Problem C: Fan Wobbles
Remedies:
1. Check that all blades are screwed firmly into blade holders.
2. Check that all blade holders are screwed firmly into motor.
3. Check the weight of blades. All our blades are weighed on electronic scales. e weight is
marked on the reverse side of the fan blade near the motor end. All of the blades should be
the same weight to prevent fan from wobbling.
4. A balancing kit is enclosed if needed.

2
Before Assembly
1. Make sure that the fan voltage (120) is compatible with your own electrical system.
2. Check to make sure that your carton contains all the parts mentioned in the parts list.
NOTE: e box can be used as a work space to prevent any damage on the
ornamental surface.
CAUTION: Before installing, choose a location for mounting the fan where the blades
have at least 7 feet of clearance from all objects and floor. Mount an
outlet box to the ceiling or use an existing box.
CAUTION: Do not mount fan to sheet rock or drywall type materials. To insure
proper support, use the two #1 wood screws to secure mounting bracket to joist
or beam. If the location you choose does not have a suitable support beam, install a
2”x 4” brace between ceiling joists to support.
Tools you Need
1. Phillips Screwdriver
3. Adjustable Wrench
2. Flat Screwdriver
4.Wire Strippers
Screw Package
S1. Wood Screws & Washers
S2. Bracket Screws & Washers
S3. Blade Screws & Paper Washers
S4. Blade Arm Screws
S5. Wire Connectors
S6. Safety Bolt & Nut
S7. "J" Hook
S8. Zip Tie
Quantity
2
2
16
10
3
1
1
1
What You Have
Parts
1. Mounting Bracket
2. Down Rod Assembly
Rod Supplied
3. Canopy
4. Canopy Cover
5. Distributor
6. Downrod Accessory Distributor
7. Flange Cover
8. Fan Housing & Motor
9. Downrod Accessory
10. Decorative Screws
11. 50W Halogen Bulbs
12. Switch Cap Mounting Plate
13. Switch Cap
14. Finial
15. Blade Arms
16. Blades (Sold Separately)
17. Wall Control (Included)
18. Remote Control (Included)
Quantity
1
1
1
1
1
1
1
1
3
3
3
1
1
1
5
5
1
1
Hardware
Inventory
S7
S5
S6
S2
S8
S3
S4
13
12
14
1
16
15
3
42
6
7
8
9
10
11
5
17 18

3
Turn off circuit breakers and wall switch to the fan supply line leads.
30”
84”
IMPORTANT: If using the angle mount method, check to make sure the ceiling angle is not
steeper than 35º. Angles greater than 35º will require a 45º angle adapter.
t$IFDLUPNBLFTVSFCMBEFTBSFBUMFBTUwGSPNBOZPCTUSVDUJPO
t$IFDL%PXOSPE-FOHUIUPNBLFTVSFCMBEFTBSFBUMFBTUBCPWFUIFnPPS
B%PXOSPE.PVOU
/PSNBM$FJMJOHT
b.) Angle Mount
7BVMUFE$FJMJOHT
Preparation
Important: When using an existing outlet box, be sure the box is
securely attached to the building structure and can support the full
weight of the fan. Failure to do so can result in serious injury or death.

4
OUTLET BOX
Outlet Box (A)
Mounting Bracket (1)
Bracket Screws
& Washers (S2)
Support Beam
Wood Screws (S1)
Ceiling
Wood Screws (S1)
“J” Hook (S7)
Installing Mounting Bracket
Prior to securing mounting bracket, screw "J" hook (S6) into ceiling outlet box as a
secondary support means. Secure mounting bracket (#1) to the outlet box (A) by
tightening bracket screws & washers (S2) as shown. If not mounting to an outlet
box, use wood screws (S1) and washers (S1) and mount securely to ceiling beam.
Be sure at this point to insert canopy screws in bracket.
NOTE: Do not mount directly to sheet rock or ceiling tile.

5Downrod Assembly
Locate downrod assembly (#2). Loosen ball screw on black hanging ball to free
lock pin. Black hanging ball will slide down. Remove ground screw and green
ground wire. Remove hanging ball from downrod and save all parts. Insert fan
wires through downrod.

6
Tighten set screw against downrod.
Insert saftey bolt (S6) through flange & downrod
and attach nut. Tighten firmly.
read the downrod onto the motor housing
making sure the wires don’t get twisted.

7
Place Flange Cover (7),
Downrod Accessory Distributor
(6), Upper Distributor Cover
(5), Canopy Cover (4) and
Canopy (3) over downrod
assembly.
Align and insert Decorative
Screws (10) through Downrod
Accessory arm (9) with the holes
of the distributor.
Align screws on lower downrod
accessory arm with slots in the
top of the fan housing (8).
Tighten all screws securely.
Replace hanging ball, insert hanging pin through downrod and tighten set screw
through hanging ball into downrod.
WARNING: Failure to completely tighten downrod as described in steps
above could result in the fan loosening and possibly falling.

8
Lift fan onto the mounting bracket (#1). Turn housing until hanging ball seats
itself into ball socket (listen for click).
WARNING: To reduce the risk of fire, electric shock or personal injury,
mount so outlet box marked "acceptable for fan support" and use mounting
screws provided with the outlet box. Most outlet boxes commonly used for
the support of lighting fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if in doubt.
For added security, attach safety cable from fan unit to "J" hook (S7) in outlet
box. Secure by looping zip tie (S8) through safety cable and "J" hook. Tighten
zip tie securely.

9
2. After connections are made, turn
splices upward and push carefully
into outlet box. Separate black wires
on one side of the box, and white
wires on the other side.
1. Connect fan wires to ceiling
wires: white fan wire to white outlet
wire, black to black. Wire
connectors (S6 ) are provided for
your convenience.
ere are 2 colored wires coming from the top of the motor.
White (Neutral)
Ground
White
Black
Wire
Connectors
(S6)
Ground
(Green)
Black
(Power)
Outlet Box
Ground (Green)
Downrod
Ground
(Green)
Mounting Bracket
Ground (Green)

10
Loosen two screws from the hanger bracket. Align the canopy up to ceiling
and over the loosened screws. Place the canopy into the keyhole and rotate
canopy clockwise. Secure the canopy by tightening the previous loosened
screws. Rotate the canopy cover clockwise.
Attach the blades to the blade arms by
using three blade screws (S3) and paper
washers. Tighten securely.
Remove rubber shippiing grommets
before attaching blade assembly. For
blade assembly, position slot on fan
motor housing so that you can access
the screws.

11
Install the three 50W bulbs. (Included)
Take care not to touch bulb with bare
fingers. Wipe bulb with clean cloth to
remove oily residue.
Remove two set screws on the mount-
ing ring, align the keyholes of the
mounting plate and the Switch Cap
Mounting Plate, attach two screws
previously removed and tighten screws
securely.
Align the switch cap to the switch cap
mounting plate and tighten by twisting
the finial.

ON/OFF For emergency shut off.
SPEED Controls fan motor speed. To select desired speed, press
CONTROL button once and release.
REVERSE Controls direction of fan blades. To reverse fan blades, press
once and release.
FAN OFF or Turns fan motor speed off. Press once to turn off. To start
STOP motor speed again, hit one of the motor speed buttons.
L-1 or Controls the on/off and intensity* for integrated light kit. Push
UPLIGHT and release for on/off function. Hold down for full range light
dimming.
L-2 or Controls the on/off and intensity* for optional light kit. Push
DOWNLIGHT and release for on/off function. Hold down for full range light
dimming.
NOTE: The “High”, “Medium” or “Low” buttons may be used to start
the fan motor. The speed of the fan may be changed at anytime.
*Light intensity control only available with incandescent bulbs.
Remote Control Operation Instructions

IMPORTANT! PLEASE READ:
All Craftmade Ceiling Fans are prepared with a durable lacquer or a painted
finish. Your proper care will enhance both the life and appearance. Post treatments,
such as clear lacquer, are not recommended.
PROPER CARE
In order to maximize the appearance of your Craftmade ceiling fan, it is important
that dust and debris is removed from the surface periodically. It is recommended
that the motor housing be wiped down weekly using a soft, dry or damp cloth and
the blades cleaned with a soft, dry or damp cloth or fan blade duster.
DO NOT use any abrasives such as car wax, brass cleaners or other polishes, glass
cleaners or chemicals, as this will scratch/remove/ damage the protective coating.
FAILURE TO FOLLOW THE ABOVE CARE INSTRUCTIONS WILL
VOID THE WARRANTY.
For information regarding replacement parts, please write to:
Craftmade, P.O. Box 1037, Coppell, TX 75019
Please send the following information...
1. The Model Number and Finish.
2. The name of the part – if you have a parts problem.
3. Your name, mailing address and phone number (with area code).
LIMITED WARRANTY
Craftmade warrants against defects in materials or workmanship for a period of
ONE (1) YEAR from date of purchase for use, and agrees to repair or, at our option,
replace a defective unit without charge.
IMPORTANT: This Warranty does not cover damage resulting from accident,
misuse or abuse, lack of reasonable care (see above), the affixing of any attachment
not provided with the product, alteration of any attachments factory installed, loss
of parts or subjecting the fixture to any but the specified electrical service. No
responsibility is assumed for any special incidental or consequential damages.
Damages occurring during transit are not covered by this warranty.
To obtain warranty service, mail sales receipt as proof of purchase-date, and a brief
explanation of the nature of the defect, to P.O. Box 1037, Coppell, TX 75019. You
will receive, by mail, a Return Goods Authorization number issued by Craftmade
International Inc., and returned freight prepaid.
For Installation or Technical Support, call 1-800-486-4892, 8 a.m. - 5 p.m.,
Central Time, Monday-Friday.