Craftmade Ellington Manor User manual

Installation Guide
For Models:
MAN52ABZ5C4
MAN52AN5C4
net weight of fan: 23.59 lb. (10.7 kg) PRINTED IN CHINA
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pgs.4 - 5
Wiring. pg. 6
Canopy Assembly. pg. 6
Blade Assembly. pg. 7
Light Kit Assembly (Optional). pgs.7 - 8
Testing Your Fan. pg. 8
Troubleshooting. pg. 9
Warranty.pg. 9
Parts Replacement. pg. 9
READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE
Manor
4007498

SAFETY TIPS.
page 1
WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel
before you begin the fan installation or before servicing the fan or installing accessories.
1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND
SAVE THESE INSTRUCTIONS.
CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
2. Make sure all electrical connections comply with Local Codes or Ordinances, the National Electrical Code, and
ANSI/NFPA 70-1999. If you are unfamiliar with electrical wiring or if the house/building wires are different
colors than those referred to in the instructions, please use a qualified electrician.
3. Make sure you have a location selected for your fan that allows clear space for the blades to rotate,and at least
seven (7) feet (2.13 meters) of clearance between the floor and the fan blade tips. The fan should be
mounted so that the tips of the blades are at least thirty (30) inches (76 centimeters) from walls or other
upright structures.
4. The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least 35
pounds (16 kilograms). The outlet box must be supported directly by the building structure. Use only ETL or
UL listed outlet boxes marked "FOR FAN SUPPORT."
WARNING: To reduce the risk of fire,electrical shock, or personal injury, mount to the outlet box marked "Acceptable
for Fan Support of 15.9 kg (35 lbs) or less," and use the mounting screws provided with the outlet box. Most outlet
boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING: To reduce the risk of fire,electrical shock, or personal injury, wire connectors provided with this fan are
designed to accept only one 12 gauge house wire and two lead wires from the fan.If your house wire is larger than 12
gauge or there is more than one house wire to connect to the corresponding fan lead wires, consult an electrician for
the proper size wire connectors to use.
5. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be ETL or UL listed
and marked suitable for use with the model fan you are installing. Switches must be ETL or UL general use
switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
6. After installation is complete, check that all connections are absolutely secure.
7. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into
the outlet box. The wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on opposite sides of the outlet box.
WARNING: To reduce the risk of fire or electrical shock, do not use this fan with any solid state speed control device or
control fan speed with a full range dimmer switch. [Using a full range dimmer switch to control fan speed will cause a
loud humming noise from fan.] (Note:This fan is suitable for use with remote control.)
8. Do not operate the reverse switch until the fan has come to a complete stop.
9. Do not insert anything between the fan blades while they are rotating.
WARNING: To reduce the risk of personal injury, do not bend the blade arms during assembly or after installation. Do
not insert objects into the path of the blades.
WARNING: To avoid personal injury or damage to the fan and other items, be cautious when working around or
cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan blades.A dry dust cloth or lightly dampened cloth
will be suitable for most cleaning.
WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use of parts OTHER than
those provided with this fan will void the warranty.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible
conditions and situations that may occur. It must be understood that common sense and caution are necessary
factors in the installation and operation of this fan.

2. Parts Inventory.
a. canopy. 1 piece
b. hanging bracket (pre-attached to canopy).
1 piece
c. downrod and hanging ball (with pin & clip).
1 piece
d. motor housing. 1 piece
e. switch housing cap. 1 piece
f. blade arm. 5 pieces
g. glass shade. 4 pieces
h. light kit fitter. 1 piece
i. blade. 5 pieces
j. hardware packs
ab
cd
f
gh
i
j
1. Unpacking Your Fan.
Carefully open the packaging.Remove items
from Styrofoam inserts. Remove motor housing
and place on carpet or Styrofoam to avoid
damage to finish. Do not discard fan carton or
Styrofoam inserts should this fan need to be
returned for repairs.
Check against parts inventory that all parts have
been included.
page 2
required bulbs:
4 x 40 watt max. candelabra base bulbs
(included)
IMPORTANT REMINDER: You must
use the parts provided with this fan for
proper installation and safety.
e

4. Hanging Bracket Installation.
page 3
ON
OFF
ON
OFF
3. Installation Preparation.
To prevent personal injury and damage,ensure
that the hanging location allows the blades a
clearance of 7 ft. (2.13m) from the floor and 30in.
(76cm) from any wall or obstruction.
This fan is suitable for room sizes up to 400 square
feet (37.2 square meters).
This fan can also be mounted with a downrod on a
regular (no-slope) or vaulted ceiling.The hanging
length can be extended by purchasing a longer
downrod (0.5in./1.27cm diameter).After installing
hanging bracket, continue to Section 5 on page 4 for
those instructions. This fan can also be mounted as
a flushmount on a regular (no-slope) ceiling. After
installing hanging bracket, continue to Section 6 on
page 5 for those instructions.
Installation requires these tools:
Phillips screwdriver, flat-head screwdriver,
adjustable pliers or wrench, stepladder, wire
cutters,and rated electrical tape.
Vaulted ceiling
angle is not to
exceed 20 degrees.
downrod
installation flushmount
installation
12ft. - 20ft.
12ft. - 20ft.
(3.66m - 6.1m)
(3.66m - 6.1m)
blade edge
7 feet
(2.13m) (76cm)
30
inches
Turn off circuit breakers to current fixture from breaker panel
and be sure operating light switch is turned to the
OFF position.
WARNING: Failure to disconnect power supply prior to
installation may result in serious injury.
Remove existing fixture.
WARNING: When using an existing outlet box, be sure the outlet
box is securely attached to the building structure and
can support the full weight of the fan. Ensure the outlet box is
clearly marked "Suitable for Fan Support." If not, it must be
replaced with an approved outlet box. Failure to do so can result
in serious injury.
CAUTION: Be sure outlet box is grounded properly and that a
ground wire (GREEN or bare) is present.
Partially loosen screws in slotted holes of canopy. Remove
the other 2 screws (along with the star washers)--save for later
use. Twist canopy to remove hanging bracket.
Install hanging bracket to outlet box using original screws,
spring washers and flat washers provided with new or
original outlet box.* If installing on a vaulted ceiling, face
opening of hanging bracket towards high point of ceiling.
Arrange electrical wiring around the back of the hanging
bracket and away from the bracket opening.
*Note: It is very important that you use the proper hardware
when installing the hanging bracket as this will support the fan.
hanging bracket
spring washers
outlet box screws
flat washers

page 4
5. Fan Assembly (with downrod).
Remove hanging ball from downrod provided
by loosening set screw on hanging ball.Remove
pin and clip. Lower hanging ball and remove
stop pin.Then slide hanging ball off downrod.
[Refer to diagram 1.]
Loosen yoke set screws and nuts at top of motor
housing. [Refer to diagram 2.]
Tip: To prepare for threading electrical wires
through downrod, apply a small piece of
electrical tape to the ends of the electrical
wires--this will keep the wires together when
threading them through the downrod. [Refer to
diagram 2.]
Determine the length of downrod you wish to
use. Thread electrical wires through threaded
end of downrod and pull extra wire slack from
the upper end of the downrod. [Refer to
diagram 2.]
Thread downrod into the motor housing yoke
until holes for pin and clip in downrod align
with holes in yoke--make sure wires do not get
twisted. Re-insert pin and clip previously
removed. Tighten yoke set screws and nuts
securely. [Refer to diagram 2.]
Slide canopy over downrod. [Refer to
diagram 3.]
Thread wires through hanging ball; then slide
hanging ball over downrod--the top of the
downrod should be noted as having a set screw
hole; use this hole when setting the set screw.
Insert stop pin into top of downrod and raise
hanging ball. Be sure stop pin aligns with slots
on the inside of the hanging ball.Tighten set
screw securely. [Refer to diagram 4.]
WARNING: Failure to tighten set screw (on
hanging ball) completely could result in the fan
becoming loose and possibly falling.
["Fan Assembly" continued on next page.]
NOTE: The important safety precautions and
instructions appearing in the manual are not meant to
cover all possible conditions and situations that may
occur. It must be understood that common sense and
caution are necessary factors in the installation and
operation of this fan.
diagram 2
diagram 1
diagram 4
downrod
electrical wiring
yoke set screw
and nut
pin
clip
set screw
hanging ball
stop pin
pin
clip
set screw hole
hanging ball
stop pin
diagram 3
canopy
motor
housing
downrod

page 5
With the hanging bracket secured to the outlet box and
able to support the fan, you are now ready to hang your
fan. Grab the fan firmly with two hands.Slide downrod
through opening in hanging bracket and let hanging
ball rest on the hanging bracket.Turn the hanging ball
slot until it lines up with the hanging bracket tab.
WARNING: Failure to align slot in hanging ball with tab
in hanging bracket may result in serious injury or death.
Tip: Seek the help of another person to hold the
stepladder in place and to lift the fan up to you once
you are set on the ladder.
Continue to "Wiring" section for wiring diagram.
5. Fan Assembly (with downrod).(cont.)
6. Fan Assembly (flushmount).
Remove and set aside canopy cover to reveal 6
holes.Notice that 3 holes are larger than the
others.
If there are only 3 screws in top of motor
housing, please proceed to next paragraph. If
there are 6 screws in top of motor housing,
removed every other screw and lock washer.
Thread wiring through canopy. Place canopy
over yoke,aligning larger holes in canopy with
the 3 existing screws in top of motor housing.
Insert the 3 screws and 3 lock washers that were
removed (if there were only 3 screws located in
top of motor housing, these screws/lock washer
will be located in one of the hardware packs) into
the remaining holes.Securely tighten these
screws.
To prepare the fan for wiring, hang fan onto
hanging bracket by sliding the canopy over the
hanging bracket tab. (Use one of the non-slotted
holes on the rim of the canopy to do so.)
canopy
motor housing
hanging bracket tab
canopy
canopy cover
canopy
motor housing
yoke
hanging ball slot
hanging bracket tab

black
black
white
white
blue
black supply wire
ground (green
or bare)
white supply wire
7.Wiring.
page 6
*
from ceiling
from fan
CAUTION: Be sure outlet box is properly grounded
and that a ground wire (GREEN or Bare) is present.
Make sure all electrical connections comply with
Local Codes or Ordinances and the National
Electrical Code. If you are unfamiliar with electrical
wiring or if the house/building wires are different
colors than those referred to in the instructions
below, please use a qualified electrician.
When downrod is secured in place on the
hanging bracket, electrical wiring can be made
as follows:
Connect BLACK and BLUE wire from fan to
BLACK wire from ceiling with wire connector
provided.
Connect WHITE wire from fan to WHITE wire
from ceiling with wire connector provided.
Connect all GROUND (GREEN) wires together
from fan to BARE/GREEN wire from ceiling with
wire connector provided.
If you intend to control the fan light with a
separate light switch,connect BLUE wire from
fan to the BLACK (or RED) supply from the
independent switch.
* Wrap each wire connector separately with
electrical tape as an extra safety measure.
This fan is remote control adaptable (remote
control sold separately).
8. Canopy Assembly.
canopy
hanging bracket
ground
(green or bare)
Raise canopy to hanging bracket, aligning
slotted holes in canopy with loosened screws in
hanging bracket.Twist canopy to lock. Re-insert
screws (along with star washers) that were
previously removed (page 3, Section 4) and
secure all screws with Phillips screwdriver.

page 7
9. Blade Assembly.
motor housing
blade arm
blade
blade attachment
screws and washers
blade arm
screws
lock washers
10. Light Kit Assembly (Optional).
switch housing
Time Saver: Washers for blade screws can be set
on each blade screw prior to installing blades.
Locate 15 blade attachment screws and washers
in hardware pack.Hold blade arm up to blade and
align holes.Insert 3 blade attachment screws
(along with washers) with fingers first and then
tighten screws securely with a Phillips screwdriver.
Repeat for the remaining blades.
Remove blade arm screws and lock washers from
underside of motor. If plastic motor locks are
installed with blade arm screws, discard plastic
motor locks (save blade arm screws and lock washers
to secure blade arms). Align blade arm holes with
motor screw holes and attach blade arm with lock
washers and blade arm screws. Before securing
screws permanently, repeat this procedure with
remaining blade arms. Securely tighten all screws.
Note:Tighten blade arm screws twice a year.
plastic
motor
lock
motor
housing
Remove 3 screws and star washers from switch
housing cap.
If you wish to use your fan WITHOUT the light kit,
align holes in switch housing cap with holes in switch
housing. (Note:The gap on the top edge of the switch
housing cap must align with the reverse switch on the
switch housing for the proper fit.) Secure switch
housing cap with 3 screws that were just removed.
Please proceed to Section 11 on the following page to
complete installation without light kit.
If you wish to use your fan WITH the light kit,
locate BLACK (or BLUE) and WHITE wires in
switch housing labeled FOR LIGHT. Remove and
discard plastic that holds these 2 wires together.
Remove the hex nut and lock washer from threaded
rod in light kit fitter. Punch center cap out of switch
housing cap with a screwdriver. Feed wires from
light kit fitter through center hole in switch
housing cap. Screw switch housing cap onto
threaded rod on light kit fitter followed by lock
washer and hex nut.Tighten hex nut over lock
washer for a secure fit.
["Light Kit Assembly" continued on next page.]
switch housing
cap
switch housing cap
hex nut
lock washer
light kit fitter
center cap
threaded
rod

page 8
It is recommended that you test fan before finalizing
installation. Restore power from circuit box and light
switch (if applicable).Test fan speeds with the pull chain
on switch housing. Start at the OFF position (no blade
movement).First pull will set the fan to HI.Second pull will
set the fan to MEDIUM.Third pull will set the fan to LOW.
Fourth pull will re-set the fan to OFF setting.Test lights
with pull chain in the middle.If fan and/or lights do (does)
not function, please refer to "Troubleshooting" section to
solve any issues before contacting Customer Service.
Turn fan completely off before moving the reverse switch.
Set reverse switch to recirculate air depending on the
season:
- DOWN position in summer (diagram 1)
- UP position in winter (diagram 2)
A ceiling fan will allow you to raise your thermostat setting
in summer and lower your thermostat setting in winter
without feeling a difference in your comfort.
Important: Reverse switch must be set either completely
UP or completely DOWN for fan to function. If the reverse
switch is set in the middle position (diagram 3),fan will
not operate.
Attach pull chain extensions supplied or custom pull chain
extensions (sold separately) to the ends of the pull chains.
11.Testing Your Fan.
10. Light Kit Assembly (Optional).(cont.)
Connect BLACK (or BLUE) wire from switch
housing to BLACK wire from light kit fitter.
Connect WHITE wire from switch housing to
WHITE wire from light kit fitter. Be sure that
molex connections snap together securely.
Align holes in light kit fitter with holes in switch
housing. (Note:The gap on the top edge of the
switch housing cap must align with the reverse
switch on the switch housing for the proper fit.)
Attach light kit fitter with screws that were
removed on previous page.Securely tighten all
3 screws with a Phillips screwdriver.
Attach 4 glass shades using thumbscrews
provided in one of the hardware packs. Do NOT
overtighten thumbscrews as glass may crack or
break.
Install 4 candelabra base 40 watt max. bulbs
(included).
Important:When replacing bulbs, please allow
bulb(s) and glass shade(s) to cool down before
touching them.
diagram 1 diagram 2 diagram 3
switch
housing
motor
housing
pull chain extension
for fan
reverse
switch
black wire
black
(or blue)
wire
white
wire
molex connections
white wire
thumb-
screws
glass shade
light kit fitter
bulb
light pull chain
extension

Troubleshooting. Warranty.
page 9
Parts Replacement.
Problem: Fan fails to operate.
Solutions:
1. Check wall switch to fan.
2.Verify that reverse switch is set completely in
either direction.
3. Check that fan is wired properly.
Problem: Light kit (optional) not lighting.
Solutions:
1. Check wall switch to fan.
2. Check that bulbs are installed correctly.
3. Check that wires in canopy are wired properly.
4.Verifty that molex connections in switch
housing are connected properly.
Problem: Fan operates but lights fail (if
applicable).
Solutions:
1. Check that bulbs are installed correctly.
2. Check to be sure wires in canopy are wired
properly.
3.Verify that molex connections in switch
housing are connected properly.
4. Replace defective bulbs with same type of
bulb.
Problem: Lighting source (up-light, down-light
or both) not functioning.
Solution:
Wattage Limiting Device has interrupted the
flow of electricity to the light source.Ensure
bulbs total no more than 190W in the light
source.
Problem: Fan wobbles.
Solutions:
1. Use the balancing kit in one of the hardware
packs. If no blade balancing kit is provided,
please call Customer Support,1-800-486-4892,to
request one.
2. Check to be sure set screw(s) on motor
housing yoke is (are) tightened securely.
3. Check to be sure set screw on hanging ball is
tightened securely.
CRAFTMADE/ELLINGTON LIFETIME WARRANTY:
CRAFTMADE/ELLINGTON warrants this fan to the original
household purchaser for indoor use under the following
provisions:
1-YEAR WARRANTY: CRAFTMADE/ELLINGTON will replace
or repair any fan which has faulty performance due to a
defect in material or workmanship.Contact
Craftmade/Ellington Customer Service at 1-800-486-4892
to arrange for return of fan. Return fan, shipping prepaid, to
Craftmade/Ellington.We will repair or ship you a
replacement fan,and we will pay the return shipping cost.
5-YEAR WARRANTY: CRAFTMADE/ELLINGTON will repair or
replace at no charge to the original purchaser any fan
motor that fails to operate satisfactorily when failure
results from normal use.
RETURN FAN MOTOR ONLY, shipping prepaid, to
Craftmade/Ellington.We will repair or ship purchaser a
replacement motor and Craftmade/Ellington will pay the
return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY:
CRAFTMADE/ELLINGTON will repair the fan, at no charge
for labor only to the original purchaser, if the fan motor
fails to operate satisfactorily when failure results from
normal use.Parts used in the repair will be billed to the
purchaser at prevailing prices at time of repair.
The purchaser shall be responsible for all costs incurred
in the removal, reinstallation and shipping of the product
for repairs.
This warranty does not apply when damage from
mechanical, physical, electrical or water abuse results in
causing the malfunction. Deterioration of finishes or other
parts due to time or exposure to salt air is specifically
exempted under this warranty.
Neither Craftmade/Ellington nor the manufacturer will
assume any liability resulting from improper installation or
use of this product. In no case shall the company be liable
for any consequential damages for breach of this, or any
other warranty expressed or implied whatsoever.This
limitation as to consequential damages shall not apply in
states where prohibited.
For parts and information,please refer to
"Parts Inventory" on page 2.
Ellington Customer Support:
1-800-486-4892
www.craftmadebrands.com
WARNING: Failure to disconnect power supply prior to
troubleshooting any wiring issues may result in serious
injury.