Craftmade Loris LO52 User manual

Before Assembly
1. Make sure that the fan voltage (120) is compatible with your own electrical
system.
2. Check to make sure that your carton contains all the parts mentioned in the
parts list.
NOTE: e box can be used as a work space to prevent any damage on the
ornamental surface.
CAUTION: Before installing, choose a location for mounting the fan where the
blades have at least 7 feet of clearance from all objects and oor. Mount an
outlet box to the ceiling or use an existing box
CAUTION: Do not mount fan to sheet rock or drywall type materials. To
insure proper support, use the two #1 wood screws to secure mounting bracket
to joist or beam. If the location you choose does not have a suitable support
beam, install a 2”x 4”brace between ceiling joists to support.
OUTLET BOX
Outlet Box
Mounting Bracket (1)
Bracket Screws
& Washers (S3)
Support Beam
Wood Screws (S1)
Canopy Screws
Ceiling
Wood Screws (S1)
“J” Hook (S7)
Installing Mounting Bracket
Prior to securing mounting bracket, screw "J" hook (S7) into ceiling outlet
box as a secondary support means. Secure mounting bracket (1) to the outlet
box by tightening bracket screws and washers (S3) as shown. If not mounting
to an outlet box, use wood screws and washers (S1) and mount securely to
ceiling beam.
NOTE: Do not mount directly to sheet rock or ceiling tile.
read the downrod onto the motor housing making sure the wires don’t get
twisted. Insert safety bolt (S6) through ange and downrod and attach nut.
Tighten rmly.Tighten top set screw against downrod.
WARNING: Failure to completely tighten downrod as described in
steps above could result in the fan loosening and possibly falling.
WARNING: Failure to completely tighten downrod as described in
steps above could result in the fan loosening and possibly falling.
Lift fan onto the mounting bracket (1). Turn housing until hanging ball seats
itself into ball socket (listen for click).
WARNING: To reduce the risk of re, electric shock or personal injury,
mount to outlet box marked "acceptable for fan support" and use mounting
screws provided with the outlet box. Most outlet boxes commonly used for
the support of lighting xtures are not acceptable for fan support and may
need to be replaced. Consult a qualied electrician if in doubt.
For added security, attach safety cable from fan unit to "J" hook (S7) in outlet
box. Secure by looping zip tie (S8) through safety cable and "J" hook. Tighten
zip tie securely.
White (Neutral)
Ground
White
Black
Wire
Connectors
(S5)
Ground
(Green)
Blue
Black
(Power)
Outlet Box
Ground (Green)
Downrod
Ground
(Green)
Mounting Bracket
Ground (Green)
2. After connections are made,turn
splices upward and push carefully
into outlet box. Separate blue and
black wires on one side of the box,
and white and green wires on the
other side.
1. Connect fan wires to ceiling
wires: white fan wire to white
outlet wire, black to black and
green to green. Wire connectors
(S5) are provided for your
convenience. If an additional blue
wire is present then also connect
the blue wire to the black wire.
Attach canopy (3) to the mounting bracket by placing screws into slot in
canopy. Twist clockwise to lock into place. Tighten screws rmly. Next, lock
the canopy ring into place at the bottom of the canopy.
Installation Instructions
Instrucciones de instalación
Instructions d’installation
LO52
P. O. Box 1037
650 S. Royal Lane, Suite 100
Coppell, TX 75019 EE.UU.
(800) 486- 4892
8:00 a 5:00 CST (Hora local central)
Número de fax sin cargo: [phone]
Correo electrónico: [email protected]
www. craftmade.com
P. O. Box 1037
650 S. Royal Lane, Suite 100
Coppell, TX 75019 EE.UU.
de 8 heures à 17 heures (Heure standard du centre)
Numéro de télécopieur gratuit : [phone]
Email: [email protected]
www. craftmade.com
P.O. Box 1037
650 S. Royal Lane, Suite 100
Coppell, TX 75019
[phone]
8:00 to 5:00 CST (Central Standard Time)
Toll Free Fax: [phone]
email: [email protected]
www.craftmade.com
Loris
Ceiling Fan
Trouble Shooting
Problem A: Fan Will not Start
Remedies:
1. Check fuse or circuit breaker and replace if necessary
2. Turn off electrical power and check all wire connectors.
3. Check on/off TCS and wall control selector switch. See operation instructions.
Problem B: Fan is Excessively Noisy
Remedies:
1. Check that all screws in fan assembly are tight and properly seated.
2. Check to make sure mounting bracket is installed properly.
3. Check to make sure light kit and glass are installed properly and tight.
4. If wall control is used, insure the wall control is not a transformer or a variable speed type.
Problem C: Fan Wobbles
Remedies:
1. Check that all blades are screwed firmly into blade holders.
2. Check that all blade holders are screwed firmly into motor.
3. Check the weight of blades. All our blades are weighed on electronic scales. e weight is
marked on the reverse side of the fan blade near the motor end. All of the blades should be
the same weight to prevent fan from wobbling.
4. A balancing kit is enclosed if needed.
Read and Save ese Safety Precautions
1. Turn off electricity at main switch before wiring or servicing fan in order to avoid
possible electrical shock.
2. All wiring must be in accordance with the National Electric Code (ANSI/NFPA70-1999) and local
electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. After making the wire connections, the wires should be spread apart with the grounded
conductor and the equipment-grounding conductor on the one side of the outlet box
and the ungrounded conductor on the other side of the outlet box.
4. e splices after being made should be turned upward and pushed carefully up into the outlet box.
5. Conductor of a fan identified as grounded conductor to be connected to grounded conductor of
power supply, conductor of a fan identified as ungrounded conductor to be connected to an
ungrounded conductor of power supply, conductor of fan identified for equipment grounding to be
connected to an equipment-grounding conductor.
6. Fan should not be mounted in an area where it might get wet.
7. WARNING:To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked
"Acceptable for Fan Support" and use mounting screws provide with the outlet box.
e outlet box and its support must be able to support the moving weight of the fan (at least 35lbs).
8. For safety and best operating results, we recommend that you have a qualified
electrician assemble and install your fan.
9. WARNING:To reduce the risk of fire or electric shock, use the fan only with solid state speed control
device provided.
10.WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing
the brackets, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
11.Net Weight: e weight of the complete fan, including assembly hardware is ??? lbs.
Quantity
1
1
1
1
1
1
1
1
3
3
1
1
1
Parts
1. Mounting Bracket
2. Down Rod Assembly 6" Rod
3. Canopy
4. Canopy Ring
5. Flange Cover
6. Fan Housing & Motor
7. Blade Arm Flywheel
8. Light Kit
9. Blade Arms
10. Blades
11. Glass Bowl
12. Bulb
13. Universal Remote Control
What You Have
1
2
3
4
5
6
7
8
9
10
11
12
13
Turn o circuit breakers and wall switch to the fan supply line leads.
IMPORTANT: If using the angle mount method, check to make sure the ceiling angle is
not steeper than 35º. Angles greater than 35ºwill require a 45ºangle adapter.
• Check to make sure blades are at least 30” from any obstruction.
• Check Down rod Length to make sure blades are at least 7’ above the oor.
a.) Downrod Mount
(Normal Ceilings)
b.) Angle Mount
(Vaulted Ceilings)
Preparation
Important: When using an existing outlet box, be sure the box is
securely attached to the building structure and can support the full
weight of the fan. Failure to do so can result in serious injury or death.
Downrod Assembly Wiring
Blade Arm Assembly Light Kit Assembly
Tools you Need
1. Phillips Screwdriver 2. Adjustable Wrench 3. Flat Screwdriver 4.Wire Strippers
ere are 4 colored wires coming from the top of the motor.
(including ground wire).
Assemble blade arms to blade arm ywheel with the 6 motor screws (S9)
provided. Repeat for all blade arms. Assemble blade arm ywheel to fan
motor with 10 motor screws (S9) provided. Tighten screws securely.
NOTE: Depending on downrod length and ceiling clearance, it may be
necessary to assemble blades to blade arms (Step 12) prior to attaching
blade arm y wheel to fan motor.
Align holes of blade arm to blade, assemble blade to blade arm with screws
(S4) provided and tighten securely, repeat for all blades.
Connect light kit wires to motor housing. Attach light kit to
mounting plate with 3 screws provided. Tighten screws securely.
Screw Package
S1. Wood Screws and Washers
S2. Screws (for Canopy)
S3. Bracket Screws & Washers
S4. Blade Screws
S5. Wire Connectors
S6. Safety Bolt & Nut
S7. "J" Hook
S8. Zip Tie
S9. Motor Screws
Quantity
2
3
2
10
3
1
1
1
17
Hardware
Inventory
S2
S9
S3 S4 S5 S6
S7 S8
S1
Install halogen light bulb into fan. Screw bulb firmly into socket.
Install glass bowl, twist into place.
Locate downrod assembly (2). Loosen ball screw on black hanging ball to
free lock pin. Black hanging ball will slide down.Remove ground screw and
green ground wire. Remove hanging ball from downrod and save all parts.
Insert fan wires through threaded end of downrod.
Place ange cover, canopy ring and canopy in order over downrod assembly.
Replace hanging ball, insert hanging pin through downrod and tighten set
screw though hanging ball into downrod.
30”
84”
ON/OFF For emergency shut off.
HIGH Controls fan motor speed. To select desired speed, press
MEDIUM button once and release.
LOW
REVERSE Controls direction of fan blades. To reverse fan blades, press
once and release.
FAN OFF Turns fan motor speed off. Press once to turn off. To start
motor speed again, hit one of the motor speed buttons.
L-1 Controls no function on this fan.
L-2 Controls the on/off and intensity for optional light kit. Push
and release for on/off function. Hold down for full range light
dimming.
NOTE: The “High”, “Medium” or “Low” buttons may be used to start
the fan motor. The speed of the fan may be changed at anytime.
Remote Control Operation Instructions
123
45678
10 11
3
8
12 13