Read and Save ese Safety Precautions
1. Turn off electricity at main switch before wiring or servicing fan in order to
avoid possible electrical shock.
2. All wiring must be in accordance with the National Electric Code
(ANSI/NFPA70-1999) and local electrical codes. Electrical installation
should be performed by a qualified licensed electrician.
3. After making the wire connections, the wires should be spread apart with
the grounded conductor and the equipment-grounding conductor on the
one side of the outlet box and the ungrounded conductor on the other side
of the outlet box.
4. e splices after being made should be turned upward and pushed carefully
up into the outlet box.
5. Conductor of a fan identified as grounded conductor to be connected to
grounded conductor of power supply, conductor of a fan identified
as ungrounded conductor to be connected to an ungrounded conductor of
power supply, conductor of fan identified for equipment grounding to be
connected to an equipment-grounding conductor.
6. Fan should not be mounted in an area where it might get wet.
7. To reduce the risk of fire, electric shock or personal injury, mount to outlet
box marked "Acceptable for Fan Support" and use mounting screws provide
with the outlet box.
8. For safety and best operating results, we recommend that you have a
qualified electrician assemble and install your fan.
9. WARNING: To reduce the risk of fire or electric shock, do not use this fan
with any solid state speed control device.
10. To reduce the risk of personal injury, do not bend the blade brackets when
installing the brackets, balancing the blades or cleaning the fan.
Do not insert foreign objects in between rotating fan blades.
Turn off circuit breakers and wall switch to the fan supply line leads.
Before Assembly
1. Make sure that the fan voltage (120) is compatible with your own electrical
system.
2. Check to make sure that your carton contains all the parts mentioned in the
parts list.
NOTE: e box can be used as a work space to prevent any damage on the
ornamental surface.
CAUTION: Before installing, choose a location for mounting the fan where
the blades have at least 7 feet of clearance from all objects and floor. Mount an
outlet box to the ceiling or use an existing box
CAUTION: Do not mount fan to sheet rock or drywall type materials. To
insure proper support, use the two #1 wood screws to secure mounting bracket
to joist or beam. If the location you choose does not have a suitable support
beam, install a 2”x 4” brace between ceiling joists to support.
S1
S2
S3
S4
S5
S7
S6
Hardware
Inventory
Tools you Need
1. PhillipsSc rewdriver
3. Adjustable Wrench
2. Flat Screwdriver
4. Wire Strippers
Screw Package
S1. Wood Screws & Washers
S2. Screws (for Canopy)
S3. Bracket Screws & Washers
S4. Blade Screws
S5. Wire Connectors
S6. Safety Bolt & Nut
S7. "J" Hook
S8. Zip Tie
Quantity
2
3
2
3
1
1
1
What You Have
Parts
1. Mounting Bracket
2. Down Rod Assembly
4" Rod Supplied
3. Canopy
4. Flange Cover
5. Fan Housing & Motor
6. Light Kit with Glass
7. Blades Arms
8. Blades (Sold Se parately)
1
2
4
5
Quantity
1
1
1
1
1
1
4
4
30”
84”
IMPORTANT: If using the angle mount method, check to make sure the ceiling angle is
not steeper than 35º. Angles greater than 35º will require a 45º angle adapter.
t$IFDLUPNBLFTVSFCMBEFTBSFBUMFBTUwGSPNBOZPCTUSVDUJPO
t$IFDL%PXOSPE-FOHUIUPNBLFTVSFCMBEFTBSFBUMFBTUBCPWFUIFnPPS
a.) Downrod Mount
(Normal Ceilings)
b.) Angle Mount
(Vaulted Ceilings)
Preparation
Important: When using an existing outlet box, be sure the box is
securely attached to the building structure and can support the full
weight of the fan. Failure to do so can result in serious injury or death.
065-&5#09
Outlet Box (A)
Mounting Bracket (1)
Bracket Screws
& Washers (S3)
Support Beam
Wood Sc re ws (S1)
Canopy Screws (S2)
Ceiling
Wood Sc re ws (S1)
“J” Hook (S8)
Installing Mounting Bracket
Prior to securing mounting bracket, screw "J" hook (S8) into ceiling outlet box
as a secondary support means. Secure mounting bracket (#1) to the outlet box
(A) by tightening bracket screws & washers (S3) as shown. If not mounting to
an outlet box, use wood screws (S1) and washers (S3) and mount securely to
ceiling beam. Be sure at this point to insert canopy screws (S2) in bracket.
NOTE: Do not mount directly to sheet rock or ceiling tile.
Tighten set screw (A) against downrod.
Insert safety bolt (S7) through flange & down-
rod and attach nut. Tighten firmly.
read the downrod onto the motor housing
NBLJOHTVSFUIFXJSFTEPOUHFUUXJTUFE
-JGUGBOPOUPUIFNPVOUJOHCSBDLFU5VSOIPVTJOHVOUJMIBOHJOHCBMMTFBUT
itself into ball socket (listen for click).
WARNING: To reduce the risk of fire, electric shock or personal injury,
mount so outlet box marked "acceptable for fan support" and use mount-
ing screws provided with the outlet box. Most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified electrician if in doubt.
For added security, attach safety cable from fan unit to "J" hook (S8) in
outlet box. Secure by looping zip tie (S9) through safety cable and "J" hook.
Tighten zip tie securely.
White ( Neutral)
Ground
White
Black
Wire
Connectors
(S6)
Ground
(Green)
Blue
Black
(Power)
Outlet Box
Ground (Green)
Downrod
Ground
(Green)
Mounting Brack et
Ground (Green)
2. After connections are made
with wire connectors, turn splices
upward and push carefully into
outlet box. Separate blue and black
wires on one side of the box, and
white and green wires on the other
side.
1. Connect fan wires to ceiling
wires: white fan wire to white
outlet wire, black to black and
green to green. Wire connectors
(S6) are provided for your conve-
nience. If an additional blue wire is
present then also connect the blue
wire to the black wire. (Optional
light kit may be wired to
individual wall switches, if
desired.)
ere are up to 4 colored wires coming from
the top of the motor (including ground wire).
P. O. B o x 1037
650 S. Royal Lane, Suite 100
Coppell, TX 75019 EE.UU.
(800) 486- 4892
8:00 A 5:00 CST (Hora local central)
Número de fax sin cargo: (877) 304-1728
www. craftmade.com
P. O. B o x 1037
650 S. Royal Lane, Suite 100
Coppell, TX 75019 EE.UU.
de 8 heures à 17 heures (Heure standard du centre)
Numéro de télécopieur gratuit : (877) 304-1728
www. craftmade.com
P.O. B ox 1037
650 S. Royal Lane, Suite 100
Coppell, TX 75019
(800) 486-4892
8:00 To 5:00 CST (Central Standard Time)
Toll Free Fax: (877) 304-1728
email: customerservice@craftmade.com
www.craftmade.com
Olivier Ceiling Fans
Trouble Shooting
Problem A: Fan Will not Start
Solutions:
1. Check fuse or circuit breaker and replace if necessary
2. Turn off electrical power and check all wire connectors.
3. Check on/off TCS and wall control selector switch. See operation
instructions.
Problem B: Fan is Excessively Noisy
Solutions:
1. Check that all screws in fan assembly are tight and properly seated.
2. Check to make sure mounting bracket is installed properly.
3. Check to make sure light kit and glass reinstalled properly and
tight.
4. If wall control is used, insure the wall control is not a transformer
or a variable speed type.
Problem C: Fan Wobbles
Solutions:
1. Check that all blades are screwed firmly into blade holders.
2. Check that all blade holders are screwed firmly into motor.
3. Check the weight of blades. All our blades are weighed on
electronic scales. e weight is marked on the reverse side of the
fan blade near the motor end. All of the blades should be the same
weight to prevent fan from wobbling.
4. A balancing kit is enclosed if needed.
3
7
6
Downrod Assembly Attaching Downrod to Motor Housing
-PDBUFEPXOSPEBTTFNCMZ-PPTFOCBMMTDSFXPOCMBDLIBOHJOHCBMMUP
free lock pin. Black hanging ball will slide down. Remove ground screw and
green ground wire. Remove hanging ball from downrod and save all parts.
Insert fan wires through downrod.
Place flange cover (4) over downrod
assembly. Attach antenna wire to flange
cover. Place canopy screw cover over
downrod. Place canopy (3) over
downrod (2).
Replace hanging ball, insert hanging pin through downrod and tighten set
screw "C" in hanging ball into downrod.
WARNING: Failure to completely tighten downrod as described in
steps above could result in the fan loosening and possibly falling.
Attach canopy (3) to the mounting bracket
by placing screws (S2) into slot in canopy.
Twist clockwise to lock into place.
Seat the canopy screw cover into slots
and twist to lock.
Tighten screws firmly.
Slide the blades into place, support
and attach with motor screws.
Assemble Blade Arms to Blades using the (S4) Blade Screws.
Screw in candelabra light bulbs. (included)
Attach light kit fitter using the 3 screws (Supplied).
Disassemble the light kit. First, unscrew
the decorative finial followed by the small
hex nut. Remove rubber washer. Next
carefully lift the light kit cage from the
fitter base. Now carefully remove the light
kit glass and set in a safe place until later.
Reattach the light kit glass, light kit cage,
rubber washer, small hex nut and
decorative finial.
8
123
45678
910 11 12 13
