Craftsman 358.350280 User manual

Operator's Manual
CRAFTSMA
2,6 cu.in./42cc 2-Cycle
GASOLINE CHAIN SAW
Model No.
358.350280 - 18 in. Bar
@
&WARNING:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
For answers to your questions about this product:
Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.
1-800-235-5878 <Hoo,o,,sted are Centra, Time)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
530087860 8/20/00
g
g
e
0
0
g

Warranty 2 Storage 16
Safety Rules 2 Trouble Shooting Chart 17
Assembly 5 Emissions Statement 18
Operation 6 Parts List 20
Maintenance tl Spanish 23
Service and Adjustments 14 Parts & Ordering Back
FULL ONE YEAR WARRANTY ON CRAFTSMAN GAS CHAIN SAW
For one year from the date of purchase, when this Craftsman Gas Chain Saw is
maintained, lubricated and tuned up according to the operator's manual, Sears
wilt repair, free of charge, any defect in material or workmanship.
This warranty excludes the bar, chain, spark plug and air filter, which are
expendable parts and become worn during normal use.
If this Gas Chain Saw is used for commercial or rental purposes, this warranty
applies for 30 days from the date of purchase.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THIS CHAIN SAW TO THE
NEAREST SEARS SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Sears, Roebuck and Co., D/817 WA, Hoffman Eotateo, IL 60179
A_kWARNING: Always disconnect
spark plug wire when making repairs
except for carburetor adjustments. Be-
cause a chain saw is a high-speed
woodcutting tool, careless or improper
use of this toot can cause serious
injury.
PLAN AHEAD
• Restrict the use of your saw to adult
users who understand and can follow
the safety rules, precautions, and op-
erating instructions found in this
manual
Hearing A.,L/_ Safety Hat
Protection _ Eye
Snug I q_'gI'_-_ Protection
Fitting _ Heavy Duty
Clothing _oves
Safety
Shoes %_m
• Wear protective gear. Always use
steel-toed safety footwear with non-
slip soles; snug-fitting clothing;
heavy-duty, non-slip gloves; eye pro-
tection such as non-fogging, vented
goggles or face screen; an approved
safety hard hat; and sound barriers
(ear plugs or mufflers) to protect your
hearing. Regular users should have
hearing checked regularly as chain
saw noise can damage hearing. Se-
cure hair above shoulder length.
• Keep all parts of your body away
from the chain when the engine is
running,
• Keep children, bystanders, and ani-
mals at least 30 feet (10 meters)
away from the work area when start-
ing and using the saw.
• Do not handle or operate a chain
saw when you are fatigued, ill, or up-
set, or if you have taken alcohol,
drugs, or medication. You must be in
good physical condition and mentally
alert. If you have any condition that
might be aggravated by strenuous
work, check with doctor before oper-
ating.
• Do not start cutting until you have a
clear work area, secure footing, and
especially if you are felling a tree, a
retreat path.
2

OPERATEYOURSAWSAFELY
•Do not operate with one hand. Seri-
ous injury to the operator, helpers, or
bystanders may result from one-
handed operation. A chain saw is in-
tended for two-handed use.
• Operate the chain saw only in a welt-
ventilated outdoor area.
• Do not operate saw from a ladder or
in a tree, unless you are specifically
trained to do so.
• Make sure the chain will not make
contact with any object while starting
the engine. Never try to start the saw
when the guide bar is in a cut.
• Do not put pressure on the saw, es-
pecially at the end of the cut. Doing
so can cause you to lose control
when the cut is completed,
• Stop engine before setting saw
down.
• Hand carry saw only when engine is
stopped. Carry with muffler away
from body; guide bar & chain project-
ing behind you; guide bar preferably
covered with a scabbard.
MAINTAIN YOUR SAW tN GOOD
WORKING ORDER
• Have all chain saw service per-
formed by a quaIified service dealer
except the items listed in the mainte-
nance section of this manual.
• Make certain the saw chain stops
moving when the throttle trigger is
released. For correction, refer to
CARBURETOR ADJUSTMENTS.
• Keep the handles dry, clean, and
free from oil or fuel mixture.
• Keep caps and fasteners securely
tightened.
• Use only Craftsman accessories and
replacement parts as recommended.
Never modify your saw.
HANDLE FUEL WITH CAUTION
• Do not smoke while handIing fuel or
while operating the saw.
• Eliminate all sources of sparks or
flame in areas where fuel is mixed or
poured.
• Mix and pour fueI in an outdoor area
and use an approved, marked con-
tainer for all fuet purposes. Wipe up
atl fuel spilis before starting saw.
• Move at least 10 feet (3 meters) from
fueiing site before starting.
• Turn the engine off and tet saw coot
in a non-combustible area, not on
dry leaves, straw, paper, etc, Slowly
remove fuet cap and refuet unit.
• Store the unit and fuel in a coot, dry
well ventilated space where fuel va-
pors cannot reach sparks or open
flames from water heaters, electric
motors or switches, furnaces, etc.
GUARD AGAINST KICKBACK
Follow all safety rules to help avoid
kickback and other forces which can
result in serious injury.
Clear The Working Area
A0&WARNING: Rotational Kickback
can occur when the moving chain con-
tacts an object at the upper portion of
the tip of the guide bar, Contact at the
upper portion of the tip of the guide bar
can cause the chain to dig into the ob-
ject, which stops the chain for an
instant. The result is a lightning fast,
reverse reaction which kicks the guide
bar up and back toward the operator.
Pinch-Kickback and Pull-In occur
when the chain is suddenly stopped by
being pinched, caught, or by contact-
ing a foreign object in the wood. This
sudden stopping of the chain results in
a reversat of the chain force used to
cut wood and causes the saw to move
in the opposite direction of the chain
rotation. Pinch-Kickback drives the
saw straight back toward the operator.
Putt-In pulls the saw away from the op-
erator.
REDUCE THE CHANCE OF
KICKBACK
• Recognize that kickback can happen.
With a basic understanding of kick-
back, you can reduce the element of
surprise which contributes to acci-
dents.
• Never tet the moving chain contact
• any object at the tip of the guide bar.
Keep working area free from obstruc-
tions such as other trees, branches,

rocks,fences,stumps,etc.Eliminate
oravoidanyobstructionthatyour
sawchaincouldhitwhilecutting.
• Keepsawchainsharpandproperly
tensioned.Alooseordullchaincan
increasethechanceofkickback.
Followmanufacturer'schainsharp-
eningandmaintenanceinstructions.
Checktensionatregularintervals,
butneverwithenginerunning.Make
surebarclampnutsaresecurely
tightened.
• Beginandcontinuecuttingatfuit
speed.Ifthechainismovingata
slowerspeed,thereisgreater
chanceofkickbackoccurring.
• Useextremecautionwhenreenter-
ingacut.
• Donotattemptcutsstartingwiththe
tipofthebar(ptungecuts),
• Watchforshiftinglogsorotherforces
thatcouldcloseacutandpinchor
fallintochain.
• UsethespecifiedReduced-Kickback
GuideBarandLow-KickbackChain.
Avoid Pinch-Kickback:
• Be extremely aware of situations or
obstructions that can cause material
to pinch the top of or otherwise stop
the chain.
• Do not cut more than one tog at a
time.
• Do not twist saw as bar is withdrawn
from an undercut when bucking.
Avoid Pull-In:
• Always begin cutting with the engine
at full speed and the saw housing
against wood.
• Use wedges made of plastic or
wood, Never use metal to hold the
cut open.
MAINTAIN CONTROL
Stand to the left ofthe saw
Thumb on \[
underside
of handlebar
Never reverse h'_nd'positions locked
• A good, firm grip on the saw with
both hands will help you maintain
control. Don't let go. Grip the rear
handle with your right hand whether
you are right or left handed. Wrap the
fingers of your left hand over and
around the front handlebar, and your
left thumb under the front handlebar.
Keep your left arm straight with the
elbow locked.
• Position your left hand on the front
handlebar so it is in a straight line
with your right hand on the rear han-
dle when making bucking cuts.
Stand slightly to the left side of the
saw to keep your body from being in
a direct line with the cutting chain.
• Stand with your weight evenly bal-
anced on both feet.
• Do not overreach. You could be
drawn or thrown off balance and lose
control.
• Do not cut above shoulder height. It
is difficult to maintain control of saw
above shoulder height.
KICKBACK SAFETY FEATURES
'_I'WARNING: The following fea-
tures are included on your saw to help
reduce hazard of kickback; however,
such features will not totally eliminate
this danger. Do not rely only on safety
devices.
• Handguard: designed to reduce the
chance of your left hand contacting
the chain if your hand slips off the
front handlebar.
• Position of front and rear handlebars:
designed with distance between
handles and "in-line" with each other.
The spread and "in-line" position of
the hands provided by this design
work together to give balance and
resistance in controlling the pivot of
the saw back toward the operator if
kickback occurs.
• Reduced-Kickback Guide Bar: de-
signed with a small radius tip which
reduces the size of the kickback
danger zone. This type bar has been
demonstrated to significantly reduce
the number and seriousness of kick-
backs when tested in accordance
with ANSI B175.1.
r_. Small Radius
Tip Guide Bar
Large Radius
Tip Guide Bar [ /
• Low-Kickback Chain: has met kick-
back performance requirements when
tested on a representative sample of
chain saws below 3.8 cubic inch
displacement specified in ANSI Bt75.1.

Low-KickbackChain
ContouredDepthGauge
_ IongatedGuardLink
DeflectsKickback
ForceAndAllows
WoodToGradually
RidekltoCutter
SAFETY NOTICE: Exposure to
vibrations through prolonged use of
gasoline powered hand tools could
cause blood vessel or nerve damage
in the fingers, hands, and joints of
people prone to circulation disorders or
abnormal swelling. Prolonged use in
cotd weather has been linked to blood
vessel damage in otherwise healthy
people, tf symptoms occur such as
numbness, pain, toss of strength,
change in skin color or texture, or loss
of feeling in the fingers, hands, or
joints, discontinue the use of this tool
and seek medical attention. An
anti-vibration system does not
guarantee the avoidance of these
problems. Users who operate power
tools on a continual and regular basis
must closely monitor their physical
condition and the condition of this toot.
CHAIN BRAKE: tf this saw is to be
used for commercial logging, you must
order and install a chain brake to com-
ply with Federal QSHA Regulations for
Commercial Logging. Contact your
Sears Service Center or catt
1-800-235-5878.
SPARK ARRESTOR: Your saw is
equipped with a temperature limiting
muffler and spark arresting screen
which meets the requirements of
California Codes 4442 and 4443. Ati
U.S. forest land and the states of
California, Idaho, Maine, Minnesota,
New Jersey, Oregon, and Washington
require by law that many internal
combustion engines be equipped with
a spark arrestor screen. If you operate
a chain saw in a state or locale where
such regulations exist, you are legally
responsible for maintaining the
operating condition of these parts.
Failure to do so is a violation of the
law. Refer to Customer
Responsibilities chart in the
MAINTENANCE section.
STANDARDS: This chain saw is listed
by Underwriters Laboratories, Inc. in
accordance with American National
Standards for Gasoline-Powered
Chain Saws Safety Requirements
(ANSI Bt75.t-t 99t).
CARTON CONTENTS
Check carton contents against the fol-
lowing list.
Model 358.350280
Chain Saw (fully assembled)
Bar toot
2-cycle engine oil
Chain sharpening tool
Carrying case
Gloves
Wedge
Log carrier
Pruning saw
Examine parts for damage. Do not use
damaged parts.
If you need assistance or find that
parts are missing or damaged, please
call 1-800-235-5878.
NOTE: It is normal to hear the fuel filter
rattle in an empty fuel tank.
Your unit has been factory tested and
the carburetor precisely adjusted. As a
result you may smell gasoline or find a
drop of oil/fuet residue on the muffler
when you unpack the unit.
ASSEMBLY
Your saw is fully assembled; no
assembly is necessary.

KNOWYOURSAW
READ THIS OPERATOR'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR
CHAIN SAW. Compare the illustrations with your unit to famiIiarize yourself with the
location of the various controls and adjustments. Save this manual for future ref-
erence,
Bar Tool
(chain adjustment)
Muffler
Chain
CRAFTSMRN
Front Handle
JStarter Rope
_j ON/STOP
witChpdmer
Bulb
Bar Oil FillCap Starter Fuel Mix Fill Cap
Housing
Throffle
Lockout
Rear
Handle
Cylinder Cover
Chain
Direction
of Travet
Throttle Choke Bar Clamp Chain Bar Clamp Nuts Guide Bar
Trigger Lever Catcher
ON/STOP SWITCH
The ON/STOP SWITCH is used to stop
the engine,
THROTTLE TRIGGER
The THROTq-LETRIGGER controls en-
gine speed,
THROTTLE LOCKOUT
The THROTTLE LOCKOUT must be
pressed before you can squeeze the
throttle trigger, This feature prevents
you from accidentaIly squeezing the
trigger.
CHOKE/FAST IDLE LEVER
The choke and fast idte are set by pull-
ing the CHOKE/FAST IDLE LEVER out
fully for cotd or refueled starting, The
choke provides additional fuel to the
engine during cotd starting,
PRIMER BULB
The PRIMER BULB circulates fuel to the
carburetor to provide quicker starting.
CHAIN TENSION
tt is normal for a new chain to stretch
during first 30 minutes of operation.
You should check your chain tension
frequentIy. See CHAIN TENSION under
the SERVICE AND ADJUSTMENTS sec-
tion.
6

BEFORESTARTINGENGINE
4_WARNING: Be sure to read the
fuel handling information in the safety
rules section of this manual before you
begin, tf you do not understand the
fuel handling information do not at-
tempt to fuel your unit. Seek help from
someone that does understand the in-
formation or cati the customer assis-
tance help line at 1-800-235-5878.
GUIDE BAR AND CHAIN OIL
The chain oiler provides continuous
lubrication to the chain and guide bar.
Be sure to fitI the bar oil tank when you
flit the fuet tank (Capacity = 6.8 ft. oz.).
For maximum guide bar and chain life,
we recommend you use Craftsman
chain saw bar oil. If Craftsman bar oit
is not available, you may use a good
grade SAE 30 oil untit you are aMe to
obtain Craftsman brand. The oil output
is automatically metered during opera-
tion. Your saw will use approximately
one tank of bar oil for every tank of fuel
mix. Always fill the bar oit tank when
you fill the fueI tank.
FUELING ENGINE
This engine is certified to operate on
unIeaded gasoIine. Before operation,
gasotine must be mixed with a good
quality 2-cycte air-cooled engine oil.
We recommend Craftsman brand oil
Mix gasoline and oil at a ratio of 40:1
(A 40:1 ratio is obtained by mixing 3.2
ounces of oil with 1 gailon of unleaded
gasoline). DO NOT USE automotive oil
or boat oil These oils will cause
engine damage. When mixing fuel
follow the instructions printed on the
container.
Once oiI is added to the gasoline,
shake container momentarily to assure
that the fuel is thoroughly mixed.
Always read and foltow the safety ruIes
relating to fuel before fueling your unit.
IMPORTANT
Experience indicates that alcohoI
blended fuels (catied gasohoI or using
ethanol or methanoI) can attract mois-
ture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine white in storage.
To avoid engine problems, the fuel sys-
tem should be emptied before storage
for 30 days or longer. Drain the gas
tank, start the engine and _etit run until
the fuel tines and carburetor are empty.
Use fresh fuel next season. See STOR-
AGE instructions for additional informa-
tion.
Never use engine or carburetor clean-
er products in the fuel tank or perma-
nent damage may occur.
See the STORAGE section for addition-
al information.
mLWARNING: The chain must not
move when the engine runs at idle
speed, if the chain moves at idle
speed, refer to CARBURETOR ADJUST-
MENTwithin this manual. Avoid con-
tact with the muffler. A hot muffIer can
cause serious burns.
STOPPING YOUR ENGINE
• Move ON/STOP switch to STOP.
STARTING YOUR ENGINE
To start the engine, hoid the saw firmly
on the ground as illustrated. Make
sure the chain is free to turn without
contacting any object.
Important point8 to remember
When pulting the starter rope, do not
use the fut[ extent of the rope as this
can cause the rope to break. Do not
let starter rope snap back. Hold the
handle and [et the rope rewind slowly.
For cold weather starting, start the unit
at FULL CHOKE; allow the engine to
warm up before squeezing the throttle
trigger. Do not cut material with the
choke/fast idle lever at the FULL
CHOKE position.
Starter Rope Handle
/('k_l_-_.k _ Lett Hand
_ _ on Front
Right Foot Through Rear Handle
COLD ENGINE OR WARM ENGINE
AFTER RUNNING OUT OF FUEL
NOTE: tn the following steps, when
the choke/fast idte lever is pulled out to
the fuit extent, the correct throttIe set-
ting for starting is set automatically.
_ On/Stop
Switch
Primer
Bulb

• MoveON/STOPswitchtoONposition.
Ch°keC°b
• Pulloutchoke/fastidletothefullex-
tent.
• Slowlypressprimerbulb6times.
• Pullthestarterropequicklywithyour
righthand5times;thenpushthe
choke/fastidleleverincompletely(to
theOFFCHOKEposition).
• Pullthestarterropequicklywithyour
righthanduntiltheenginestarts.
• Allowtheenginetorunforapproxi-
matelyfiveseconds.Then,squeeze
andreleasethrottletriggertoallow
enginetoreturntoidlespeed.
STARTINGAWARM ENGINE
• Pull the choke/fast idle lever out to
the full extent, then push the lever
back in completely (to the OFF
CHOKE position).
• Slowly press primer bulb 6 times.
• Pull the starter rope quickly with your
right hand until the engine starts.
• Squeeze and release throttle trigger,
allowing engine to idle.
DIFFICULT STARTING OR
STARTING A FLOODED ENGINE
The engine may be flooded if it has not
started after 10 pulls.
Flooded engines can be cleared of ex-
cess fuel by following the warm engine
starting procedure listed above, tnsure
the ignition switch is in the ON position.
Starting could require pulling the start-
er rope handle many pulls depending
on how badly the unit is flooded. If en-
gine still fails to start, refer to the
TROUBLESHOOTING CHART or call
1-800-235-5878.
OPERATING TIPS
• Check chain tension before first use
and after 1 minute of operation. See
CHAIN TENSION in the MAINTENANCE
section.
• Cut wood only. Do not cut metal,
plastics, masonry, non-wood building
materials, etc.
• Stop the saw ifthe chain strikes a
foreign object. Inspect the saw and
repair parts as necessary.
• Keep the chain out of dirt and sand.
Even a small amount of dirt will
quickly dull a chain and increase the
possibility of kickback.
• Practice cutting a few small logs us-
ing the following steps. This will help
you get the '_feel" of using your saw
before you begin a major sawing op-
eration.
• Squeeze the throttle trigger and al-
low the engine to reach fuIt speed
before cutting.
• Begin cutting with the saw frame
against the tog.
• Keep the engine at full speed the
entire time you are cutting.
• Allow the chain to cut for you. Exert
only light downward pressure.
• Release the throttle trigger as soon
as the cut is completed, allowing
the engine to idle. If you run the
saw at futt throttle without a cutting
load, unnecessary wear can occur.
• To avoid losing control when cut is
complete, do not put pressure on
saw at end of cut.
• Stop engine before setting saw
down.
TREE FELLING TECHNIQUES
4HII,WARNING: Check for broken or
dead branches which can fall while
cutting causing serious injury. Do not
cut near buildings or electrical wires if
you do not know the direction of tree
fall, nor cut at night since you wilt not
be able to see welt, nor during bad
weather such as rain, snow, or strong
winds, etc.
• Carefully plan your sawing operation
in advance.
• Clear the work area. You need a
clear area all around the tree so you
can have secure footing.
• Study the natural conditions that can
cause the tree to fall in a particular
direction. These conditions include:
• The wind direction and speed.
• The lean of the tree. The lean of a
tree might not be apparent due to
uneven or sloping terrain. Use a
plumb or level to determine the di-
rection of tree lean,
• Weight and branches on one side.
• Surrounding trees and obstacles.
• Look for decay and rot. If the trunk is
rotted, it can snap and fall toward the
operator.
• Make sure there is enough room for
the tree to fall. Maintain a distance of
2-1/2 tree lengths from the nearest
person or other objects. Engine
noise can drown out a warning call.

• Removedirt,stones,loosebark,
nails,staples,andwirefromthetree
wherecutsaretobemade.
_'9_bPlanaclearretreatpath
t _ -_- Direction of Fall
45 ._
FELLING LARGE TREES
(6 inches in diameter or larger)
The notch method is used to felI large
trees. A notch is cut on the side of the
tree in the desired direction of fall. After
a felling cut is made on the opposite
side of tree, the tree will tend to felt in
the direction of the notch.
NOTE: if tree has targe buttress roots,
remove them before making the notch.
NOTCH CUT AND FELLING TREE
• Make notch cut by cutting the top of
the notch first. Cut through t/3 of the
diameter of the tree. Next complete
the notch by cutting the bottom. See
illustration. Once the notch is cut, re-
move the wedge of wood from tree.
FinaIcut here
First cut _"_1
Notch
\ Hinge
• After removing the wood, make the
felling cut on the opposite side of the
notch. This is done by making a cut
about two inches higher than the
center of the notch. This will leave
enough uncut wood between the fell-
ing cut and the notch to form a hinge.
This hinge wi_I hetp prevent the tree
from falling in the wrong direction.
Hinge holds tree on
stump and helps
control fail
damage, use wood or plastic wedges,
but never steeI or iron wedges.
• Be alert to signs that the tree is
ready to fall: cracking sounds, widen-
ing of the felling cut, or movement in
the upper branches.
• As tree starts to fa}l, stop saw, put ft
down, and get away quickly on your
planned retreat path.
• Be extremely cautious with partially
fallen t_ees that may be poorly sup-
ported. When e tree doesn't fall com-
pletely, set the saw aside and putt
down the tree with a cable winch,
bIock and tackle, or tractor Do not
use your saw to cut down a partially
fatten tree.
CUTTING AFALLEN TREE
(BUCKING)
Bucking is the term used for cutting a
fallen tree to the desired tog size.
,_t, WARNING: Do not stand on the
log being cut. Any portion can roll
causing toss of footing and control. Do
not stand downhill of the log being cut.
IMPORTANT POINTS
• Cut onty one log at a time.
• Cut shattered wood very carefully;
sharp pieces of wood could be flung
toward operator.
• Use a sawhorse to cut small logs.
Never allow another person to hold
the log while cutting and never hold
the log with your leg or foot.
•Do not cut in an area where logs,
limbs, and roots are tangled. Drag logs
into a clear area before cutting them.
BUCKING TECHNIQUES
_t, WARNING: If saw becomes
pinched or hung in a log, don't try to
force it out. You can lose control of the
saw _est_lting in in}ury a_d/or damage
to the saw. Stop the saw, drive a
wedge of plastic or wood into the cut
until the saw can be removed easily. Re-
start saw and cs.refutly reenter the cut.
Do not use a metal wedge. Do not at-
tempt to restart your saw when it is
pinched or hung in a log.
NOTE: Before felling cut is complete,
use wedges to open the cut when
necessary to control the direction of
fall, To avoid kickback and chain

Turn saw OPF and use a plastic or
wooden wedge to force cut open
Overcutting begins on the top side of
the log with the bottom of the saw
against the log. When overcutting use
light downward pressure.
Overcutting Undercutting
Undercutting involves cutting on the
underside of the log with top of saw
against the tog. When undercutting
use Iight upward pressure, Hold saw
firmly and maintain control The saw
wilt tend to push back toward you.
_WARNING: Never turn saw up-
side down to undercut. The saw can-
not be controlled in this position,
Always make your first cut on the
compression side of the log.
Firstcut on compression side of log
Second cut
First cut on compression side of log
BUCKING WITHOUT A SUPPORT
• Overcut through 1/3 of the diameter
of the log,
• Roll the tog over and finish with a
second overcut.
• Watch for togs with a compression
side. See illustration above for cut-
ting togs with a compression side.
Using a log
for support 2ndCut ,_
_1 stCut
1st Cut
BUCKING USING A LOG OR
SUPPORT STAND
• Remember your first cut is atways on
the compression side of the log. (Re-
fer to the illustration below for your
first and second cut).
• Your first cut should extend t/3 of the
diameter of the log.
• Finish with your second cut.
2ridCut __
LIMBING AND PRUNING
d_WARNING: Never climb into a
tree to limb or prune. Do not stand on
ladders, platforms, a log, or in any po-
sition which can cause you to lose
your balance or controt of the saw.
IMPORTANT POINTS
• Watch out for springpoles.
Springpotes are small size limbs
which can whip toward you, or pult
you off balance. Use extreme cau-
tion when cutting small size limbs.
• Be alert for springback. Watch out for
branches that are bent or under
pressure. Avoid being struck by the
branch or the saw when the tension
in the wood fibers is released.
• Frequently clear branches out of the
way to avoid tripping over them.
LIMBING
• Limb a tree only after it is cut down.
• Leave the larger limbs underneath the
felled tree to support the tree as you
work.
• Start at the base of the feIled tree and
work toward the top, cutting branches
and limbs. Remove small limbs with
one cut.
10