Craftsman 320.22305 User manual

Operator's Manual
ICRFIFTSMFIN I
BENCH TOP TOOL STAND
Model No. 320. 22305
_WARNING: To reduce the risk of injury,
the user must read and understand the
Operator's Manual before using
this product.
_WARNING: To reduce the risk of injury,
the user must always read and follow all
instructions in the bench top tool operating
manual before mounting the tool to
this stand.
•WARRANTY
•SAFETY
•ASSEMBLY
•DESCRIPTION
•OPERATION
•MAINTENANCE
•ESPANOL
Sears Brands Management Corporation, Hoffman Estates,
IL 60179 U.S.A.
www.craftsman.com

I_ _I[I]ii[II_I__I
Warranty Page 2
Safety Symbols Pages 4-5
Safety Instructions Page 6
Description Page 7
Assembly Pages 8-9
Operation Pages 10-13
Maintenance Page 14
Parts List Pages 15-16
CRAFTSMAN ONE YEAR FULL WARRANTY
FOR ONE YEAR from the date of purchase, this product is warranted
against any defects in material or workmanship. With proof of purchase,
defective product will be replaced free of charge.
For warranty coverage details to obtain free replacement, visit the web
site: www.craftsman.com
This warranty is void if this product is ever used while providing commercial
services or if rented to another person.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
This bench top tool stand has many features for making its use more pleasant
and enjoyable. Safety, performance, and dependability have been given top
priority in the design of this product, making it easy to maintain and operate.
SAVE THESE INSTRUCTIONS!
READ ALL INSTRUCTIONS!
Page 2 22305 ManuaLRevised_12 0528

_WARNING: Some dust created by power sanding, sawing, grinding, drilling
and other construction activities contains chemicals known to the state of
California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products,and
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemical: work in a well ventilated
area, and work with approved safety equipment, such as those dust masks that
are specially designed to filter out microscopic particles.
The purpose of safety symbols is to attract your attention to possible dangers.
The safety symbols and the explanations with them deserve your careful
attention and understanding. The symbol warnings do not, by themselves,
eliminate any danger. The instructions and warnings they give are no substitutes
for proper accident prevention measures.
22305 ManuaLRevised_12 0528 Page 3

WARNING: Be sure to read and understand all safety instructions in this
Operator's Manual, including all safety alert symbols such as "DANGER",
"WARNING", and "CAUTION" before using this stand. Failure to follow all
instructions listed below may result in electric shock, fire, and/or serious
personal injury.
SYMBOL SIGNAL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION; may
be used in conjunction with other symbols or pictographs.
DANGER: Indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING: Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury.
Damage prevention and Information Messages
These inform the user of important information and/or instructions that could
lead to equipment or other property damage if they are not followed. Each
message is preceded by the word "NOTICE", as in the example below:
NOTICE: Equipment and/or property damage may result if these instructions are
not followed.
WARNING: To ensure safety and reliability, all repairs should be performed
by a qualified service technician.
_, WARNING: The operation of any power tools can result in
foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with side shield
and a full face shield when needed. We recommend a Wide
Vision Safety Mask for use over eyeglasses or standard safety
glasses with side shields. Always use eye protection that is
marked to comply with ANSI Z87.1.
Page 4 22305 ManuaLRevised_12 0528

SAVE THESE INSTRUCTIONS
Some of the following symbols may be used on this tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to
operate the tool better and more safely.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
rain Minutes Time
Alternating Current Type of current
--'_: Direct Current Type or a characteristic of current
n 0 No Load Speed Rotational speed, at no load
] Class II Construction Double-insulated construction
.../min Per Minute Revolutions, strokes, surface speed,
orbits, etc., per minute
Wet Conditions Alert Do not expose to rain or use in damp
locations.
To reduce the risk of injury, user must
Read The Operator's Manual read and understand operator's manual
before using this product.
OAlways wear safety goggles or safety
Eye Protection glasses with side shields and a ful! face
shield when operating this product.
,_ Alert Precautions that involve
Safety your safety.
Failure to keep your hands away from the
No-Hands Symbol blade will result in serious personal injury.
No-Hands Failure to keep your hands away from the
Symbol blade will result in serious personal injury.
Failure to keep your hands away from the
No-Hands Symbol blade will result in serious personal injury.
Failure to keep your hands away from the
No-Hands Symbol blade will result in serious personal injury.
To reduce the risk of injury or damage,Hot Surface avoid contact with any hot surface.
22305 ManuaLRevised_12 0528 Page 5

GENERAL SAFETY RULES
WARNING: Read all safety warnings and instructions. Failureto follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
READ AND SAVE THESE INSTRUCTIONS
A
JL WARNING: Do not modify this tool and/or used it for any application other
than that for which it was designed.
•Do not use for scaffolding or as ladder. Do not stand or climb on the
bench top tool stand; it could fall or tip over, causing serious injury.
•Do not overload. The maximum capacity for the bench top tool stand
is 3001bs.
•Do not apply an unbalanced load. This could cause the bench top tool
stand to tip over.
• Store the stand properly. Do not store the bench top tool stand outdoors
or in a damp location.
•Keep the work area clean, uncluttered, and well lit. Do not work on or
place the bench top tool stand legs on floor surfaces that are slippery from
sawdust, oil, water or wax.
• Keep children and bystanders away while operating a power tool.
Distractions may cause you to lose control. Visitors should wear the same
safety equipment as the operator.
• When using a power tool with the bench top tool stand, always follow
the safety instructions in the power tool's Operator's Manual.
• Always wear safety glasses or eye shields when operating power tools.
•Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or long
hair can be caught in moving parts. Always wear non-slip footwear. Tie back
long hair. Roll long sleeves above the elbow.
• Always use clamps or other practical ways to support the workpiece
and secure it to astable platform. Holding the work by hand or against
your body is unstable and may lead to loss of control.
Page 6 22305 ManuaLRevised_12 0528

ID]=_.'_o_[[o_]
KNOW YOUR BENCH TOP TOOL STAND (Fig. 1)
This Bench Top Tool Stand is ideal for mounting most Craftsman and other
brands of bench top tools. It has a large base and is height adjustable for
working comfort. The strong, wide base provides stable support for the tool.
There are foot leveler pads on each foot for maximum stability. The 20-gauge
steel construction supports up to 300 Ibs. The durable, powder-coat finish
stands up to rugged use.
Fig. 1 Support (Long)
Support(Short)
Upper Leg
Lowerleg
support(Short)
Lower leg
Lower Foot-Leveling-Pad
Weight
Working heights
PRODUCT SEPCIFICATIONS
14.3 Ibs
34. in (Maximum)
32. in
30. in
28. in
26. in
24. in
22. in. (Minimum)
Maximum Load Capacity 300 Ibs
22305 ManuaLRevised_i2 0528 Page 7

A
Jk WARNING: If any parts are broken or missing, do not attempt to operate the
bench top tool stand until the broken or missing part is replaced. Failure to do
so could result in serious injury.
_WARNING: Do not attempt to modify this bench top tool stand or create
accessories not recommended for use with this bench top tool stand. Any such
alteration or modification is misuse and could result in a hazardous condition
leading to serious injury.
UNPACKING
This product has been shipped disassembled.
• Carefully remove all the parts and accessories from the carton. Make sure
that all items listed in the packing list are included.
• Inspect the parts for the bench top tool stand carefully to make sure that no
breakage or damage occurred during shipping.
• Do not discard the packing material until you have carefully inspected and
satisfactorily operated the bench top tool stand.
• If any parts are damaged or missing, please return the bench top tool stand
to the place of purchase.
PACKAGE CONTENTS
Item Description Qty.
A/
B
D
Long Tabletop Supports
Short Tabletop Supports
2
2
Upper Leg 4
Lower Leg 4
Page 8 22305 ManuaLRevised_12 0528

Item Description Qty.
E
F
G
H
K
Long Lower Leg Supports
©
©
@
©
Short Lower Leg Supports
2
2
Screw M6"10 32
Nut M6 32
Foot 4
Foot-Leveling Pad 4
L Foot Screw M8"40 4
M Foot nut M8 8
N Foot Washer M8 4
22305 ManuaLRevised_12 0528 Page 9

[IY.]_/[I]][
WARNING: Do not use this tool for scaffolding or as a ladder. Make sure to
tighten all screws securely prior to use. Maximum capacity: 300 Ibs.
ASSEMBLING THE TABLETOP
SUPPORTS (Fig. 2)
Place the 2 Long Tabletop
Supports (A) and the 2 Short
Tabletop Supports (B) on a flat
work surface so they form
a rectangle.
Fig. 2 A
ASSEMBLING THE UPPER
LEGS (Fig. 3 and Fig. 4)
Connect the 4 Upper Legs
(C) to the four corners on the
Tabletop Supports by inserting
the 16 Screws (G) through the
Tabletop Supports and then
through the 4 clearance holes
on the top of each Upper Leg.
Then attach a Nut (H) to each
screw and finger- tighten only.
NOTICE: The upper Legs must
be attached to the inside of the
Tabletop Supports.
Fig .3
Fig .4
G
C
Page 10 22305 ManuaLRevised_12 0528

ASSEMBLING THE LOWER
LEGS AND LOWER LEG
SUPPORTS (Fig. 5 and Fig. 6)
1. Determine the desired
height for the tabletop and
then select the desired set
of height adjustment holes
on the lower legs.
2. Attach the Lower Legs (D)
to the Upper Legs (C) using
the 16 screws (G). Before
attaching the 16 Nuts
(H), position the Lower
Supports (E and F).
NOTICE: Finger-tighten only
until all screws and nuts are
in place. Then tighten all nuts
securely, using a wrench
and screwdriver.
Fig. 5
Fig. 6
G
D
E
C
22305 ManuaLRevised_12 0528 Page 11

ASSEMBLING THE LEVELING
DEVICE (Fig. 7 and Fig. 8)
1. Insert Foot Screw (L) into
Foot-Leveling Pad (K).
2. Thread Foot Screw (L) with
Foot-Leveling Pad (K) into
the first nut (M).
3. Place Foot Washer (N)
and the second nut (M) on
the Foot (K). Thread Foot
Screw (L) through Foot- (J),
Foot Washer (N), and the
second nut (M).
4. Place the stand in an
upright position at the
desired work height. Make
final adjustments to the
foot leveling pads and
tighten all nuts securely.
dI0 tol Foo_Leveling
Fig. 8 M
N
K©
Page 12 22305 ManuaLRevised_12 0528

USING A PLYWOOD
TABLE TOP (SOLD
SEPARATELY) (Fig. 9)
Some tools, such as table
saws, require adding a wood
tabletop (not included) for
proper mounting to this tool
stand for stability. For this
purpose there are 8 holes (0)
(2 in each corner) of the 4
tabletop supports to mount
a wood tabletop (mounting
screws sold separately).
We recommend using a 24-in.
long X 18-in. wide X 3/4-in.
thick plywood tabletop
(sold separately).
1. Turn the stand upside
down on top of the
plywood table top and
mark the positions of the
8 attachment holes (2
each on tops of each
tabletop support).
2. Drill holes in plywood at
the locations of the marks.
3.
4.
5.
Fig. 9
!0
Place the stand in the
upright position and place
the plywood on top of
the stand.
Fig. 10
©
Place mounting screws (P),
sold separately, into the 8
holes in plywood
and through the
attachment holes in the
tabletop supports.
Insert nuts (Q), sold separately, onto screws and tighten securely.
\
/
!
//
22305 ManuaLRevised_12 0528 Page 13

WARNING: When servicing, use only identical replacement parts. Use of any
other parts may create a hazard or cause product damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible
to damage from various types of commercial solvents and may be damaged by
their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING: When servicing, use only identical replacement parts. Use of any
other parts may create a hazard or cause product damage. To ensure safety and
reliability, all repairs should be performed by a qualified service technician.
_WARNING: Keep the bench top tool stand dry, clean, and free from oil
and grease. Always use a clean cloth when cleaning. Never use brake fluids,
gasoline, petroleum based products or any strong solvent to clean the bench
top tool stand. Chemicals can damage, weaken or destroy plastic which may
result in serious personal injury.
Page 14 22305 ManuaLRevised_12 0528

I_Zf_i 1,.1BE,.IIi
BENCH TOP TOOL STAND MODEL NO. 320.22305
The Model Number will be found on the Nameplate attached to the support leg
of the bench top tool stand. Always mention the Model Number when ordering
parts for this tool.
To order parts, call 1-800-469-4663.
\
6
22305 ManuaLRevised_12 0528 Page 15

l_Z_l i,.1BE,.IIi
BENCH TOP TOOL STAND MODEL NO. 320.22305
The Model Number will be found on the Nameplate attached to the support leg
of the bench top tool stand. Always mention the Model Number when ordering
parts for this tool.
To order parts, call 1-800-469-4663.
1 2040203013 Long Tabletop Supports 2
2 2040203014 Short Tabletop Supports 2
3 2040203015 Upper Leg 4
4 2040203016 Lower Leg 4
5 2040203017 Long Lower Leg Supports 2
6 2040203018 Short Lower Leg Supports 2
7 1010118015 Screw M6"10 32
8 1010202004 Nut M6 32
9 1020303003 Foot 4
10 1020908002 Foot-Leveling Pad 4
11 1010132006 Foot Screw M8"40 4
12 1010201005 Foot nut M8 8
13 1010301014 Foot Washer M8 4
Page 16 22305 ManuaLRevised_12 0528

Manual de Operacibn
ICRRFTSMRN I
ESTANTE PARA HERRAMIENTA DE BANCO
Modelo No. 320.22305
_ADVERTENCIA: Para reducir el riesgo
de lesiones, el usuario debe leer y
comprender el Manual de Operacibn
antes de usar este producto.
ADVERTENCIA: Para reducir el riesgo
de lesibn, el usuario siempre debe leer y
seguir todas las instrucciones en el manual
de operacibn de la herramienta de banco
antes de montar la herramienta al estante.
• GARANTiA
• SEGURIDAD
• ENSAMBLAJE
°DESCRIPCION
•OPERAClON
•MANTENIMIENTO
°ESPANOL
Sears Brands Management Corporation, Hoffman Estates,
IL 60179 U.S.A.
www.craftsman.com

Garantia Pa.gina 18
Simbolos de Seguridad Pa.ginas 20-21
Instrucciones de Seguridad Pa.gina 22
Descripcion Pa.gina 23
Ensamblaje Pa.ginas 24-25
Operacion Pa.ginas 26-29
Manteni miento Pa.gina 30
Lista de Partes Pa.ginas 31-32
GARANTiA TOTAL DE UN AI_IO DE CRAFTSMAN
POR UN ANO despues de la fecha de compra, este producto esta. garantizado
por cualquier defecto de materiales o fabricacion. Si cuenta con la prueba de
compra, el producto defectuoso sera. reemplazado sin costo alguno.
Para detalles sobre la cobertura de garantia para obtener una
devoluci6n gratuita, visite la p&gina web: www.craftsman.com
Esta garantia se anulara., si el producto ha sido usado mientras se proveia
servicios comerciales o si se ha rentado a otra persona.
Esta garantia le otorga derechos legales especificos. Puede que usted
tenga otros derechos que varien de un Estado a otro.
Corporacion Sears Brands Management, Hoffman Estates, IL 60179 U.S.A.
Este estante para herramienta de uso pesado tiene muchas caracteristicas
dise_adas para obtener un uso ma.s placentero. AI dise_ar este producto, se le
ha otorgado ma.xima prioridad a la seguridad, el rendimiento y la confiabilidad,
haciendolo fa.cil de mantener y operar.
iGUARDE ESTAS INSTRUCCIONES!
!LEA TODAS LAS INSTRUCCIONES!
P_gina 18 22305 ManuaLRevisado_12 0528

ADVERTENClA: Algunas particulas de polvo que se generan al lijar,
serruchar, afilar, o perforar, con herramientas electricas, asi como las
actividades de construccion, contienen quimicos que el estado de California
reconoce como causantes de ca.ncer, nacimientos defectuosos u otros daSos
reproductivos. Algunos ejemplos de estos quimicos son:
• Plomo de pinturas hechas a base de plomo
• Silice cristalizado de ladrillos y cemento y otros productos de albaSileria, y
• Arsenio y cromo de la madera tratada quimicamente
El riesgo por el contacto con estos quimicos, varia dependiendo de cu&n
frecuente realice este tipo de trabajo. Para reducir el contacto con estos
quimicos, trabaje en un &tea bien ventilada, y con equipo con seguridad
aprobada; tales como ma.scaras para el polvo que esten especialmente
diseSadas para filtrar las particulas microscopicas.
El proposito de los simbolos de seguridad es el de dirigir su atencion hacia los
peligros posibles.
Los simbolos de seguridad y las explicaciones que los acompa5an merecen una
cuidadosa atencion y entendimiento. Los simbolos de advertencia no eliminan
los peligros por si mismos. Las instrucciones y advertencias que proveen no son
sustitutos de las medidas adecuadas de prevencion de accidentes.
22305 ManuaLRevisado_12 0528 P_gina :$9

ADVERTENClA: AsegQrese de leer y comprender todas las instrucciones
de seguridad en este manual de operacion, incluyendo todos los simbolos
de seguridad de alerta tales como "PELIGRO", "ADVERTENOIA", y
"PRECAUOION" antes de usar esta herramienta. El no seguir todas las
instrucciones que se indican a continuacion, puede ocasionar descarga
electrica, incendio, y/o grave lesion personal.
SIGNIFICADO DE LOS SiMBOLOS
SJMBOLO DE SEGURIDAD DE ALERTA: Indica PELIGRO, ADVERTENCIA, o
PRECAUCION; pueden ser usados junto con otros simbolos o pictogramas.
PELIGRO: Indica una situacion peligrosa que de no ser evitada, producira, la
muerte o lesion grave.
ADVERTENOIA: Indica una situacion peligrosa que de no ser evitada, podria
producir la muerte o lesion grave.
PRECAUOION: Indica una situacion peligrosa que de no ser evitada podria
producir lesiones menores o moderadas.
Prevenci6n de daho y mensajes informativos
Le informan al usuario de informacion importante y/o instrucciones que podrian
producir dafio al equipo u otra propiedad si no se cumplen. Cada mensaje esta.
precedido por la palabra "NOTA", como se muestra en el ejemplo aqui abajo:
AVISO: Dafio al equipo u/o otra propiedad puede producirse si no se cumplen
estas instrucciones.
ADVERTENOIA: Para asegurarse la seguridad y la confiabilidad, todas las
reparaciones deben realizarse por un tecnico de servicio calificado.
_, ADVERTENCIA: La operacion de cualquier herramienta
electrica puede causar el lanzamiento de objetos extrafios
dentro de sus ojos, Io cual puede resultar en una lesion severa
del ojo. Antes de iniciar la operacion de la herramienta
electrica, siempre use anteojos o gafas protectoras con
proteccion lateral y una ma.scara protectora para la cara
cuando sea necesario. Le recomendamos una M&scara de
Seguridad de Vision Amplia para usarse sobre sus lentes o
gafas de seguridad esta.ndar con proteccion lateral. Siempre
use proteccion a los ojos con la etiqueta de cumplimiento de
ANSI Z87.1.
P_gina 20 22305 ManuaLRevisado_12 0528