Creative Cedar Designs 3710 User manual

ASSEMBLY INSTRUCTIONS
Creative Cedar Designs • PO Box 4901 • Chattanooga, TN 37405
Visit our web site at: www.Creativecedardesigns.com or call us at 888-363-4967
© Creative Cedar Designs 2021
Cedar Chalet
3710

2
ATTENTION: READ THIS BEFORE USE OF YOUR PLAYSET OR ACCESSORY:
Observing the following statements and warnings reduces the likelihood of serious or fatal injury.
This product has been designed for single family home/residential use only and is not intended for use in any public setting. Placement in public settings constitutes misuse of this product.
Play Safe Installation Checklist:
be allowed to use the equipment until it is properly installed.
the assembly instructions of your particular product for any applicable minimum use zones.
be used only on approved designs. Do not alter the product design in any way, or add/remove any components.
also be fastened securely before use. Make certain all hardware is tightened securely.
w all protruding threaded ends of bolts and other fasteners and
(1.8 meters) from any structure or obstruction such as, but not limited to: fences, garage, house, shed,
overhanging branches, laundry lines, or electrical wires.
fall onto a hard surface can result in serious injury to the equipment user. Make certain residential playground equipment is not installed over concrete, asphalt,
packed earth or any other hard surface.
Verify that any suspended climbing ropes, chain, or cable are securely anchored at both ends and cannot be made to loop back upon itself.
protect wood surfaces and prevent cracking and warping.
adjust all swings so there is a minimum 8’’ clearance between the swing and the ground surface.
Play Safe Use Checklist:
be provided for children of all ages at all times.
your instructions for the number and weight of all occupants that may safely use this equipment singly or simultaneously,
children not to walk close to, in front of, behind, or between moving items, such as but not limited to, swings, slides and gliders.
children not to twist swing chains or ropes or loop them over the top support bar since this may reduce the strength of the chain or rope.
children to avoid swinging empty seats.
Teach children to sit in the center of the swing with their full weight on the center of the seat.
children not to use the equipment in any manner other than intended.
children not to dismount the equipment while it is in motion.
capes
and ponchos. These items can cause death by strangulation.
children not to climb on or use the playset or accessories when the products are wet.
roller slides for foreign materials that could be potentially hazardous to users,
jump ropes, clothesline, pet leashes, cables and chain as they may cause a strangulation hazard.
children to
footwear
WARNING: Lawn swings are designed for use by children two years of age and older. The use by children under the age of two can result in entrapment between the seat and back rest
because the child’s body may pass through the opening, causing entrapment of the child’ NEVER place children in a rearward facing
position or with legs between the seat and backrest.
Play Safe Maintenance Checklist:
the beginning of each play season:
Tighten all hardware.
Lubricate all metallic moving parts per manufacturer’s instructions.
ropes, cables, and chains for wear, rust,
rust.
such as swing seats or any other items that were removed for the cold season.
y.
Twice a month during play season:
Tighten all hardware.
y.
Once a month during play season:
Lubricate all metallic moving parts per manufacturer’s instructions.
ropes, cables, and chains for wear, rust,
Lubricate all metallic moving parts per manufacturer’s instructions.
and take indoors or do not use.
y.
IMPORTANT! ANCHORING AND SURFACING INSTRUCTIONS
Loose-Fill Materials:
replenish and/or redistribute the surfacing.
Do not
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles:
Placement:
Disposal Instructions:
Save this instruction sheet in the event the manufacturer needs to be contacted.

3
SAFE USE ZONE
8’’ Minimal Clearance Between Swings and Ground.
9’ 2-1/2’’
THE MINIMUM USE ZONE FOR THE PLAYSET SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF
THE UNIT. SWING USE ZONE EXTENDS NO LESS THAN 163” EACH SIDE OF THE SWING BEAM.
NO OBSTRUCTIONS, (POLES, TREES, STRUCTURES,) CAN BE INSIDE THE USE ZONE.
30’
28’

4
TOOLS REQUIRED
DRILL 7/16” & 1/2” SOCKET
& WRENCH
HAMMER ADJUSTABLE
WRENCH
TAPE MEASURE
PHILLIPS BIT CARPENTER
SQUARE
SAFETY GLASSES 1/8’’ & 5/16” DRILL BIT
SQUARE DRIVE BIT

5
INCLUDED PARTS

6
BOARD LIST

7
INCLUDED HARDWARE
NOTE: Wherever 2’’ Self Tapping
Hex Screws are used, please
pre-drill with a 1/8’’ drill bit.

8
1. Assemble roof A-Frames as shown.
WM 132
WM 131-1
WM 131
WM 130
(2) WM 125(1) WM 126
X2
X2
(34) 1 1/4’’ Square Slotted Screws
STEP 1

9
STEP 2
1. Assemble Frame ‘A’ as shown.
WM 143
WM 101
(6) 5/16’’ x 2-3/4’’ Hex Head Bolts
(6) 5/16’’ Flat Washer
(6) 5/16’’ Lock Washer
(6) 5/16’’ T-Nuts
(4) 2-3/4’’ Hex Head
Bolts
(4) Lock Washers
(4) Flat Washers
(4) 5/16’’ T-Nuts
T-Nut
Hex Head Bolt
Flat Washer
Lock Washer
Insert (2) 5/16’’
T-Nuts
Flat Washer
Lock Washer
Hex Head Bolt
FRAME ‘A’
PRO TIP:
When you attach the Roof
A-Frame to the uprights:
1. Hand tighten the hardware,
2. Stand the A-Frame up and use
a level to square the roof.
3. Tighten the hardware to lock the
frame in place.
WM 144

10
STEP 3
1. Assemble Frame ‘B’ as shown.
WM 142
WM 141
WM 123
(4) 5/16’’ x 2-3/4’’ Hex Head Bolts (8) 5/16’’ Flat Washer
(8) 5/16’’ Lock Washer
(10) 5/16’’ T-Nuts
(4) 2-3/4’’ Hex Head
Bolts
(4) Lock Washers
(4) Flat Washers
(4) 5/16’’ T-Nuts
(4) 5/16’’ x 3’’ Hex Head Bolts
WM 101
FRAME ‘B’
PRO TIP:
When you attach WM 123
to the uprights:
1. Hand tighten the hardware,
2. Stand the A-Frame up and
use a level to square the roof.
3. Tighten the hardware to
lock the frame in place.
(4) 3’’ Hex Head
Bolts
(4) Lock Washers
(4) Flat Washers
(4) 5/16’’ T-Nuts
Insert (2) 5/16’’
T-Nuts
T-Nut
Hex Head Bolt
Flat Washer
Lock Washer

11
STEP 4
1. Attach Barrier Board and Roof A-Frame to Unit Frames as shown.
(2) 5/16’’ x 2-3/4’’ Hex Head Bolts
(2) 5/16’’ Flat Washer (2) 5/16’’ Lock Washer
Flat Washer
Lock Washer
Hex Head Bolt
FRAME ‘B’
FRAME ‘A’
WM 156
(4) 2-1/2’’ Square Slotted Screws
(4) 2 1/2’’ Square
Slotted Screws

12
STEP 5
1. Assemble Deck Frame as shown.
(2) WM 122
(2) WM 108
(1) WM 121
11-1/2’’
(12) 2-1/2’’ Square Slotted Screws

13
STEP 6
1. Attach Frame ‘A’ and Frame ’B’ to the deck frame as shown.
FRAME ‘A’
FRAME ‘B’
(8) 5/16’’ x 2-3/4’’ Hex Head Bolts
(8) 5/16’’ Lock Washer (8) 5/16’’ T-Nuts
(8) 5/16’’ Flat Washer
T-Nut
Hex Head Bolt
Flat Washer
Lock Washer
PRO TIP:
Assembly is easiest with two or three people.
Hand tighten all hardware at this stage while
attaching the deck frame to the uprights. This
will allow the frames to be adjusted during the
following steps.

14
STEP 7
1. Attach the Ladder Steps as shown.
(4) WM 107
(16) 3’’ Square Slotted Screws

15
STEP 8
1. Attach Climbing Wall Boards as shown.
(44) 2-1/2’’ Square Slotted Screws
WM 102-B
WM 102-B
WM 102-B
WM 102-B
WM 102-A
WM 102-C
WM 102-C
WM 102-A
WM 102-A
WM 102-B
WM 102-C
PRO TIP:
Once the Rock Wall boards are attached and secured,
tighten all hardware securing the deck frame.

16
STEP 9
1. Attach Climbing Rocks as shown with hardware included with accessory.
1/4”-20 x 2-1/4
Hex Head Bolt
1/4” Lock
Washer
1/4-20 T-Nut
8mm Washer
Climbing
Rock

17
STEP 10
1. Install Filler Board and Barrier Support Boards as shown.
(1) WM 134
(4) 2 1/2’’ Square Slotted Screws
(1) WM 110
(1) WM 150
(6) 2” Self Tapping Hex Screws (6) 5/16’’ Flat Washer
(6) 2’’ Self Tapping
Screws
(6) Flat Washers
Per Board
(4) 2 1/2’’ Square
Slotted Screws
PRO TIP:
Check WM 150 and WM 110
with a level to make certain
they are parallel to the deck.
NOTE: Wherever 2’’ Self Tapping
Hex Screws are used, please
pre-drill with a 1/8’’ drill bit.

18
STEP 11
1. Install the Deck Boards as shown.
2. Install Slide Support Board as shown.
(87) 1 1/4’’ Square Slotted Screws
WM 146
WM 146
WM 112-1
WM 112-1
WM 112-2
(12) WM 112
ALL GAPS
1/4’’
ALIGN
SLIDE MOUNTING
HOLES
WM 159
PRO- TIP:
1. Lay out the deck boards on the deck frame.
2. Align the WM 159 and hand tighten the slide bolts,
aligning the deck boards with slide support board.
3. Check the deck boards for even spacing.
4. Secure all of the deck boards with hardware shown.
(3) 1/4’’ T-Nut
INSERT (3) 1/4’’ T-NUTS
(2) 1 1/4’’ Square
Slotted Screws
WM 159

19
STEP 12
1. Install Barrier Support boards as shown.
(4) 5/16’’ Flat Washer
WM 109 L
WM 109 R
(2) 2 1/2’’Square
Slotted Screws
(4) 2” Self Tapping Hex Screws
(2) 2’’ Self Tapping
Screws
(2) Flat Washers
(2) 2’’ Self Tapping
Screws
(2) Flat Washers
NOTE: Wherever 2’’ Self Tapping
Hex Screws are used, please
pre-drill with a 1/8’’ drill bit.
(2) 2 1/2’’ Square Slotted Screws

20
STEP 13
1. Install swing beam barrier boards as shown.
(2) WM 151
(2) WM 152
(2) WM 153
(2) WM 154
ALL GAPS
3-1/8’’
(32) 1 1/4’’ Square Slotted Screws
ROOF FRAMES
REMOVED FOR CLARITY
NOTE:
Holes in barrier boards
must align with holes in
Swing Beam Support
Board.