Crouzet GNR Mini Series Assembly instructions

INSTALLATION SHEET
MOUNTING INSTRUCTIONS
SSR - DIN-RAIL MOUNT
MINI
GNR Mini GNRD Mini
AC OUTPUT
DC OUTPUT
CROUZET SOLID STATE RELAYS - DIN RAIL MOUNT PRODUCTS have been developed to offer all the advantages of electronic switching technology. The 12 mm industrial
housing is quick to install. The product is compact and reliable. Please refer to the data sheet available on www.crouzet.com
DIN Rail - AC Output Single Phase
• Output Current of 4Amps
• Output Voltage of 12-275Va& 12-460Va
• Control Voltage of 6-30Vc, 12-30Va/ 8.5-30Vc
• Special Zero Cross Switching
DIN Rail - DC Output
• Output Current of 4Amps
• Output Voltage of 2-60Vc
• Control Voltage of 5-30Vc, 90-240Vz
1. Locate rail and align with the top part of the DIN clip in the back of the SSR
2. Using reasonable force, push the SSR in the direction of the arrows
3. To remove, place the screwdriver on the clip and push in the direction shown
WARNING: Removing product from RAIL DIN incorrectly by not using the
appropriate tool will damage the latching system
!
C.MC.DEF._____.EN
!
WARNING: The user should protect heat sensitive materials as well as people
against any contact with the product.
For correct cooling, the SSR needs air convection. Less air convection produces an
abnormal heating. In the event there is no space between two SSRs, reduce the load
current. Forced cooling (ex. fan inside the cabinet) significantly improves the thermal
performance.
For more information please go to www.crouzet.com
MOUNTING ON DIN RAIL DISMOUNTING
PART NUMBER NOMENCLATURE
GNR Mini
GNRM 4D2 A
4: 4A D2: 6-30 V c
B1: 12-30 V a |
12-30 V
a
A: 12-275 V c |
Special Zero Cross
B: 12-460 V a |
Special Zero Cross
GNR Mini
Series
Series
Output
Current
Control
Voltage
Output
Voltage
GNRD Mini
GNRDM 4D1 C
4: 4A D1: 5-30 V c
A1: 90-240 V z
C: 2-60-240 V z |
DC Switching
GNRD Mini
Series
Series
Output
Current
Control
Voltage
Output
Voltage
WIRING DIAGRAMS
GNR Mini GNRD Mini
2(- )
1(+)
LOAD
DC
-
+
4(-)
3(+)
4(-)
3(+) 2
1AC
LOAD
1
1
1. Protection Equipment: Short circuit protection GNRDM4D1C & GNRDM4A1C:
it is recommended to add an overvoltage protection
2
3
DIN rail connected to protection
wire (ground)
1

INSTALLATION SHEET
CONNECTION
WARNING
SSR - DIN-RAIL MOUNT
MINI
C.MC.DEF.___EN
WARNING
DANGER
RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE
• Confirm that the product power supply voltage and its tolerances are compatible
with those of the electrical network.
• The product's side panels may be hot, allow the product to cool before touching.
• Follow proper mounting instructions including torque values.
• Do not allow liquids or foreign objects to enter this product.
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Turn off power supply before working on this equipment.
Failure to follow these instructions can result in death, serious
injury or equipment damage.
!
For more information please go to www.crouzet.com
IMPORTANT CONSIDERATIONS TRANSIENT VOLTAGE
Electrical equipment should be installed, operated, serviced and maintained only by
qualified personnel. No responsibility is assumed by Crouzet for any consequences
arising out of use of this manual. Be sure to use input and output voltage within
operating ranges.
WARNING: The product’s side panels may be hot, allow the product to cool before
touching. Please follow mounting instructions. Failure to follow these instructions can
result in serious injury or equipment damage.
In AC power lines, transient voltages are common and may pose a risk for the
operation, load and reliability of the SSR. In Crouzet SSR, the transient protection can
rise 800 V (please refer to product datasheet).
User may also use external transient protection to the SSR for additional protection
(please refer to product datasheet).
!
CONNECTION
DERATING CURVES
SOLID
4 mm²
AWG12
2.5 mm²
AWG14
4 mm²
AWG12
2.5 mm²
AWG14
(No ferrule)
STRANDED
(With ferrule)
SOLID
(No ferrule)
STRANDED
(With ferrule)
SOLID
(No ferrule)
STRANDED
(With ferrule)
SOLID
(No ferrule)
STRANDED
(With ferrule)
4 mm²
AWG12
2.5 mm²
AWG14
4 mm²
AWG12
2.5 mm²
AWG14
NUMBER OF WIRES - Direct connection with wires with or without ferrules
1 2
1 2
NUMBER OF WIRES - Direct connection with wires with or without ferrules
INPUT WIRING
OUTPUT WIRING
SCREWDRIVER TYPE: POZIDRIV 2
RECOMMENDED TIGHTENING TORQUE:
M5 SCREW N.M
Min 0.4 / Max 0.5
RECOMMENDED TIGHTENING TORQUE:
M5 SCREW N.M
Min 0.4 / Max 0.5
Current (A)
Ambient Temperature (°C)
0
0,5
1
1,5
2
2,5
3
3,5
4
4,5
5
0 10 20 30 40 50 60 70 80 90
Current (A)
Ambient Temperature (°C)
0
0,5
1
1,5
2
2,5
3
3,5
4
4,5
0 10 20 30 40 50 60 70 80 90 100
GNR Mini - 4 A GNRD Mini - 4 A