Crutchfield 575PM500X2 Specification sheet

Source Unit
•
~----------------------1
I I
-----------------,
I
@- LEFT-@- LEFT-@ 1
@- RIGHT-@- RIGHT-@
I
-------Jo" -- ~-- -·
l-...fDJIC][)J-- ~-- _·_ ~
~~--~---------
------- ~---------- -©
INPUT CL ':=- IP ----= F= RoN =T- PA - SS- - TH - RU - R- EAR ___)
,
,
,
*Keep grounds as
short as possible
Switched 12V
to REM
REM
NEG
Battery
Amplifier Quick Setup
~ess than 18"
+
POS
REM GND
B+
Connect to chassis
ground of vehicle
* Keep grounds as
short as possible
~-----------------------------------------------~
+ _FRONT+ +
_REAR+
+
O l u~
i:hCAUTION
Be sure to connect speakers and
Punch level Control - PlC
(if equipped) after amplifier
output clip adjustment.
(see reverse)
I
-
---~ ~~-~~~~~ ® -------------------------------------------------------------------~ · : sp ~ ec ~ ific : ati : ons : su ~ bje : ct : to : cha : ng : ew ~ ith : out : no ~ tic - e.l - ma - ges - d - epi - ctt - ypi - cal - se - tup ) .
~...,.. lfAI\I all ~ ~1\ir. Refer to manual for add i tiona l wi r ing options.

Input Clip Indicator Setup
Be sure to disconnect all speakers from
the amplifier.
.6CAUTION
Failure to comply may cause damage to
connected components and/or amplifier .
Increase the source unit volume until the
Input Clip Indicator illuminates red.
Note: Input Clip can be viewed remotely
with optional PLC2.
Decrease the source unit volume slightly
until the light turns completely off . This
establishes your maximum source unit
volume for adjusting the Output Clip
Indicator .
Note: Some source units will not clip.
Amplifier Clip Indicator Setup
Insert test tone or music CD to play for setup .
Adjust the Bass & Treble levels on the source
unit to flat.
Be sure to disconnect Punch
Level Control - PLC (if
equipped) from the amplifier.
Note: Use the 40Hz@ OdB tone (Track 5) for
mono amplifier applications or the 1kHz@ OdB
tone (Track 7) for multi-channel amplifier
applications. Be sure your x-over is switched to
the appropriate filter setting.
Output Clip Indicator
Setup
Turn the source unit volume
down .
MUSIC TESTTONE '
BLUE ~ ./
~r===== ==l BLUE/REO ./ ~
~ ......... ;;;;;;;;;;;;;;; ........................... --! RED A ~
~ . 0. . 2.0
PLJNC:::H
/i\ (l)
12 . 0' ·0. 15
INPUTLEVR
v
Adjust the Input Level knob
until the Output Clip Indicator
illuminates to the appropriate
color. Repeat for all channel
levels of input.
Reconnect all speakers and
Punch Level Control - PLC (if
F:::::::::::::::~==l equipped) to the amplifier. Be
sure to maintain proper ~
speaker polarity . V
11111111
--~~~~-------------------------------~

1111111
7 80687 34395 8

!!J
ff====:-:=-:=:=
CERTIFICATE
OF
PERFORMANCE
VERIFICATION
=-
=-
=-:=-
===:3l
~
Total
Power
Total RMS Power
@
1% THO
683
watts
ALL Rockford
Fo
s
ga
te amplifiers are designed, develope
d,
manufactured and t
es
ted in accordance with the CEA-2006 a
mp
lifier rating requirement
s.
All tests
conducted at 14.4Vdc, Min. Impedance, 1kHz(ab/ad) or 100Hz (bd) unless otherwise stated.
©2012
Ro
ckford Corporation. A
ll
Rights Reversed. ROCKFORD FOSGAT
E,
and associated logos where a
pp
li
ca
ble are registered trademarks of Rockford
Corpora
ti
on 1n the United States and/or o
th
er countries. All o
th
er trademarks are the property of their respective owner
s.
Specifications subject to chan
ge
without notice.
I
II
I
N/A I
.I

Are You Engineered to Rock?
Get a One-Year Extended Warranty when you use a matching Rockford Fosgate
Amplifier Installation kit with your Amplifier!
We
want you to get the performance and reliability that made Rockford Fosgate Amplifiers famous. Using poor-
quality under-spec wiring is a guaranteed wayto get less than you paid for from your system.
We are so certain that getting your system wired to rock with the right wire and cables will make a difference, that we
will give you an additional 1 year warranty on your amp when you use the matching amplifier installation kit. See your
dealerto determine the matching kit for your amplifier.
To
extend your warranty under this program attach the serial number sticker or UPC code removed from the original
amplifier installation kit package in the box below. Keep this form along with your original purchase receipt.
One warranty extension per amplifier regardless of the number of amplifier kits purchased.Amplifier and wiring kit
must
be
purchased at the same time.
What
is
Covered
This warranty
appli~s
only
to
Rockford
Fosgate products
s~lp
td
.
~
69surh
~f,
s
bY:
Authorized Rockford Fos'gate
Deal~rs
in the United States
of
Arnerlc;a
or
.its
,'
.
possessions. Prodyct
pyrc~~
~f3
d
~
6
t
'
consumers from artAuthorized'RocRfo
Fosgate Dealer in.
anbth~fp6un
are covered
only
by
that
dQtmt
Distributorand not
by
Rockford
Corporation, · ···
Limit
on Implied Warranties
Any implied warranties including warranties
of
fitness for use and merchantability are limited in duration to the period
of
the
express warranty set forth above. Some states do not allow limitations on the length of an implied warranty, so this limitation
may not apply. No person is authorized to assume for Rockford Fosgate any other liability in connection with the sale
of
the
product.
How
to
Obtain Service Under
the
Extended Warranty Program
The amplifier must be returned by the customer (you)
or
an authorized Rockford Fosgate retailer with a copy
of
the original
receipt and the ORIGINAL Performance Verification Certificate with the serial number
or
UPC code from the amp installation
kit. Contact your Authorized Rockford Fosgate Dealer
or
our Customer Support Specialists (1-800-669-9899) for assistance.
EU
Warranty
This product meets the current EU warranty requirements, see yourAuthorized dealer for details.
'This
Additional One-Year Warranty" is only available where allowed under local laws.
Attach Amplifier Installation Kit
Serial Number or UPC Code from
original packaging here.