CSA DEWD170 User manual

INSTALLATION
INSTRUCTIONS
designer series BUILT-IN ELECTRIC WARMING DRAWER
(DEWD Designer model/dfwd full overlay model)
VIKING RANGE CORPORATION
111 FRONT STREET
GREENWOOD, MISSISSIPPI (MS) 38930 USA
[phone]
IIMMPPOORRTTAANNTT--PPLLEEAASSEERREEAADDAANNDDFFOOLLLLOOWW
•Before beginning, please read these instructions completely and carefully.
•Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
•Please observe all local ordinances. If local codes are applicable, wire in accordance with the National Electrical
Code, ANSI/NFPA 70 - latest edition.
•WARNING - To reduce the risk of electric shock and fire, do not use a flexible power-supply cord with this
appliance.
•The installer should leave these instructions with the consumer who should retain for local inspector’s use
and for future reference.
WWAARRNNIINNGG!!!!!!
Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage,
hertz, wattage, amps, and phase is attached to the product. Wiring the warming drawer with more
voltage than it is rated for may cause severe damage to the thermostat, element, and other components.
Wiring the warming drawer with less voltage than it is rated for may cause significant decrease in
performance. To reduce the risk of fire, electric shock, or injury to persons, installation work and electrical
wiring must be done by qualified people in accordance with all applicable codes and standards, including
fire-rated conditions.
GGEENNEERRAALLIINNFFOORRMMAATTIIOONN
•THIS UNIT IS NOT TO BE INSTALLED BELOW CABINETS OR WALL MOUNTED.
•When installing this unit directly below other units, only install with Viking built-in products
•Remove warming drawer carefully from carton. Remove all loose packaging and accessories.
•It is the responsibility of the installer to comply with local codes. If no local codes are applicable, wire in
accordance with the National Electrical Code, ANSI/NFPA 70 - latest edition.
•This appliance is not fused. Protect with a proper sized fuse or circuit breaker.
•Line disconnect switch, circuit breaker, or plug/receptacle of power cord connection should be readily accessible
to the operator.
•Ground unit per applicable electrical codes.
•Any installation not matching the specifications discussed in these instructions will void the manufacturer’s
warranty.
EELLEECCTTRRIICCAALLCCOONNNNEECCTTIIOONN- UUSSEECCOOPPPPEERRCCOONNDDUUCCTTOORRSSOONNLLYY..
With the appliance positioned in front of the cabinet opening, connect wire leads extending from the
power supply to the terminal block of the unit. Make sure the colored wires of the terminal block are
connected to the corresponding colored wires extending from the power supply.

2
ddeewwddCCAABBIINNEETTCCUUTTOOUUTT
•To remove drawer assembly, pull warming drawer pan out until fully extended. Slide finger along the right
and left side until you reach the black hand latches (located at the front of the rails). Pull up on both the
right and left latches and pull drawer pan support completely out.
•Slide cavity assembly into cabinet opening.
•Drill (4) pilot holes in cabinet using 1/8” drill bit. Permanently secure the warming drawer using the (4) #8
mounting screws provided.
•Replace drawer assembly.
MMooddeellddEEWWDD117700ddEEWWDD110000
25” 28“
A (63.5 cm) (71.1 cm)
CCAABBIINNEETTIINNSSTTAALLLLAATTIIOONN
Cabinet
mounting screws
(4) - 8 x 3/4” cavity
assy drawer
assy
9 5/8”
(24.4 cm)
24”
(61.0 cm)

FFRROONNTT
RREEAARR
2211//22””
((66..44ccmm))
2211//22””((66..44ccmm))
SSIIDDEE
1100””
((2255..44ccmm))
BB
CC
9911//22””
((2244..11ccmm))
2277””((6688..66ccmm))
2222””((5555..99ccmm))2233””((5588..44ccmm))
1111//22””((33..88ccmm))
3
MMOODDEELLDDEEWWDD117700DDEEWWDD110000
B 26 1/2”(67.3 cm) 29 1/2” (74.9 cm)
C 24 7/8”(63.2 cm) 27 7/8” (70.8 cm)
Interior width 18 7/8 (47.9 cm) 21 7/8” (55.6 cm)
Interior height 5 7/16” (13.8 cm) 5 7/16” (13.8 cm)
Interior depth 21 3/16” (53.8 cm) 21 3/16” (53.8 cm)
Approx. shipping
Weight 80 lb. (36 kg) 90 lb. (40.5 kg)
120V Electrical opening

4
•To remove drawer assembly, pull warming drawer pan out until fully extended. Slide finger along the right
and left side until you reach the black hand latches (located at the front of the rails). Pull up on both the
right and left latches and pull drawer pan support completely out.
•Slide cavity assembly into cabinet opening.
•Drill (4) pilot holes in cabinet using 1/8” drill bit. Permanently secure the warming drawer using the (4) #8
mounting screws provided.
•Replace drawer assembly.
MMooddeellddFFWWDD117700ddFFWWDD110000
25” 28”
A (63.5 cm) (71.1 cm)
CCAABBIINNEETTIINNSSTTAALLLLAATTIIOONN
ccuussttoommffrroonnttIINNSSTTAALLLLAATTIIOONN
•Open the drawer and remove the pan.
•Center the custom front and insulation around the inside panel.
**NNOOTTEE::MMaakkeessuurreetthheeiinnssuullaattiioonnpprroovviiddeeddiissuusseeddbbeettwweeeenntthheeccuussttoommppaanneellaannddtthheeiinnssiiddeeddoooorrppaan
neell..
•Attach the custom front with the (6) six #8 x 3/4” screws provided.
CCaabbiinneett
CCaavviittyyAAssssyy..
MMoouunnttiinnggSSccrreewwss
((44))--##88xx33//44””
((66))--##88xx33//44””ssccrreewwssttoo
aattttaacchhccuussttoommffrroonntt
ccuussttoommffrroonntt
iinnssuullaattiioonn
ddffwwDDCCAABBIINNEETTCCUUTTOOUUTT
2244””
((6611..00ccmm))
9955//88””
((2244..44ccmm))

5
MMOODDEELLDDFFWWDD117700DDFFWWDD110000
B 26”(66.0 cm) 29 ” (73.7 cm)
C 24 7/8”(63.2 cm) 27 7/8” (70.8 cm)
Interior width 18 7/8 (47.9 cm) 21 7/8” (55.6 cm)
Interior height 5 7/16” (13.8 cm) 5 7/16” (13.8 cm)
Interior depth 21 3/16” (53.8 cm) 21 3/16” (53.8 cm)
Approx. shipping
Weight 75 lb. (33.7 kg) 90 lb. (40.5 kg)
FFRROONNTT
RREEAARR
2211//22””
((66..44ccmm))
2211//22””((66..44ccmm))
110011//22””
((2266..77ccmm))
BB
CC
9911//22””
((2244..11ccmm))
221177//88””((5555..66ccmm))223311//44””((5588..77ccmm))
ccuussttoommppaanneellddiimmeennssiioonnss
3/4” thick
120V Electrical opening

Viking Range Corporation
111 Front Street • Greenwood, Mississippi (MS) 38930 USA • [phone]
Specifications subject to change without notice
For more product information, call 1-888-VIKING1 (845-4641), or visit the Viking web site at
http://www.vikingrange.com
(PS1004VR)
EELLEECCTTRRIICCDDAATTAA
•Hard wire direct with separate 15 amp minimum 2-wire with ground circuit
•120 VAC/50-60 Hz
•DEWD170/DFWD170 - 425 watts/3.6 max. amps
•DEWD100/DFWD100 - 475 watts/4.0 max. amps
F20022H
WWIIRRIINNGGDDIIAAGGRRAAMM
BBUUIILLTT--IINNEELLEECCTTRRIICCWWAARRMMIINNGGDDRRAAWWEERR
ELEMENT
PJ010022 - DEWD170/DFWD170
PJ010023 - DEWD100/DFWD100
WHITE 15”
WHITE 10”
GREEN/YELLOW 6”
GROUND
BLACK 15”
TERMINAL BLOCK
PE070147
THERMOSTAT
PB10167
INDICATOR LIGHT
PE050083
RED 6” RED 10”
NEUTRAL
GROUND
LINE
POWER SUPPLY
CONNECTIONS
BY INSTALLER
FOR CONNECTION TO THE FACTORY
INSTALLED TERMINAL BLOCK, USE
COPPER CONDUCTORS ONLY
WARNING::TO REDUCE THE RISK OF
ELECTRIC SHOCK AND FIRE, DO NOT
USE A FLEXIBLE POWER-SUPPLY CORD
WITH THIS APPLIANCE.