CYP CHDBT-1H1CL User manual

CHDBT-1H1CL
1×2 HDMI over HDMI and CAT5e/6/7 Splitter
with IR/RS-232
Operation Manual
Operation Manual

DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.0 September 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 21/06/13 Preliminary Release
RDV2 01/07/13 IR Power Pin
VS1 16/12/13 Updated text/diagrams

CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel.........................................3
6.2 Rear Panel .........................................4
6.3 IR Cable Pin Assignment ..................5
6.4 D-Sub 9-Pin Denitions ......................5
7. Connection Diagram ............................ 6
8. Specications ........................................ 7
8.1 Technical Specications ..................7
8.2 CAT5e/6/7 Cable Specication ......8
9. Acronyms ............................................... 8

1
1. INTRODUCTION
The HDMI over HDMI and CAT5e/6/7 Splitter can split and distribute a
single HDMI input and 2-way IR or RS-232 control to a single CAT5e/6/7
output and includes a simultaneous HDMI bypass output. It supports
resolutions up to 1080p Full HD, 4K×2K timing, 3D and multi-channel
digital audio formats (such as LPCM 7.1CH, Dolby TrueHD, Dolby
Digital Plus and DTS-HD). The HDMI bypass output can be connected
to a local HDMI display or cascaded to another splitter. The CAT5e/6/7
output can be connected to a CAT5e/6/7 to an HDMI receiver to
extend the operating distance up to 60 meters.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• 1×2 HDMI over HDMI and CAT5e/6/7 Splitter
• 1×IR Extender
• 1×IR Blaster
• 3.5mm Mini-jack to RS-232 Cable
• 24V DC Power Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
• Source equipment with HDMI output connector
• Display TV/Monitor with HDMI input connector
• HDMI over CAT5e/6/7 Receivers with industry standard CAT5e/6/7
cables

2
5. FEATURES
• HDMI with 4K×2K resolution and 3D support, HDCP and DVI
compliant
• Simultaneous HDMI and CAT5e/6/7 outputs
• Supports data rate from 250Mbps up to 3Gbps
• Supports a wide range of PC resolutions from VGA to WUXGA
(RB) and HDTV resolutions up to 4K×2K (3840×2160@30 Hz and
4096×2160@24 Hz)
• Supports transmission of High Denition audio: LPCM 7.1CH, Dolby
TrueHD, Dolby Digital Plus and DTS-HD Master Audio (32 kHz~192 kHz
sample rate)
• Supports distances up to 60 meters through CAT5e/6/7 cables
• Supports USB service port
• Supports control of devices via 2-way IR
• Supports RS-232 function
• 3D signal display is dependent on the TV/Display’s EDID settings
Note:
1. This system was tested with CAT6/23AWG cables, results may vary
with cables of a different specication.
2. For playback of 4k×2k HDMI source signals, a 4K×2K capable
display and High Speed HDMI cables are required.

3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
HDMI OUTHDMI IN RS232 IN
HDMI to CAT5e/6 with IR/RS232 Transmitter
1 2 3
1HDMI OUT: Connect to a HDMI display for local monitoring of the
HDMI signal or cascade to another Splitter.
2HDMI IN: Connect with source equipment such as DVD/Blu-ray
player or games console.
3RS-232 IN: Connect to a PC/Laptop or RS-232 control device (with
supplied 3.5mm Mini-jack to D-Sub 9-Pin adaptor) to transmit RS-
232 data to a suitably equipped receiver unit.
Note: This device has a last memory function and will retain the
EDID settings of the last device connected via the CAT5e/6 output
port when it is not connected to a display after power cycling.
The splitter will read the EDID settings of the device connected
to the HDMI output of the receiver unit and if it detects a 4K×2K
capable EDID it will transmit the signal in that format to the output
port. If no 4K×2K capable EDID is detected then the unit will detect
the EDID settings and send out the signal that all outputs can
accept.

4
6.2 Rear Panel
POWER
DC 24V
CAT5e/6 OUT
IR 1
BLASTER USB LINK
IR 2
EXTENDER
21 3 4 5 76
1POWER LED: The LED will illuminate when connected to an active
power supply.
2DC 24V: Connect the 24V DC power supply to the unit and plug
the adaptor into an AC outlet.
3IR 1 BLASTER: Connect the supplied IR Blaster cable for IR signal
transmission. IR signals received by an IR extender connected to
the receiver unit will be transmitted by this blaster. Place the IR
Blaster in direct line-of-sight of the equipment to be controlled.
4IR 2 EXTENDER: Connect an IR extender cable for IR signal
reception. Signals received will be transmitted from any IR blaster
connected to the receiver unit. Ensure that the remote being used
is within the direct line-of-sight of the IR Extender
5USB: This slot is reserved for rmware update only.
6LINK LED: This LED will illuminate when connected to a receiver unit
that is connected with a TV/monitor that is displaying the signal.
7CAT5e/6/7 OUT: Connect to a CAT5e/6/7 to HDMI Receiver (with
or without PoE) with a single CAT5e/6/7 cable each to extend the
HDMI signal up to 60 m.

5
6.3 IR Cable Pin Assignment
3
1
3
1
2
2
Power 3.3 V
IR Blaster Signal
NC
IR Signal
Power 3.3 V
Ground
IR Extender
IR Blaster
6.4 D-Sub 9-Pin Denitions
PIN DEFINE TX/RX
1N/C
2TxD/RxD
3RxD/TxD
4NC
5GND
6NC
7NC
8NC
9NC

6
7. CONNECTION DIAGRAM
HDMI OUT HDMI IN RS232 IN
HDMI to CAT5e/6 with IR/RS232 Transmitter
POWER
DC 24V
CAT5e/6 OUT
IR 1
BLASTER USB LINK
IR 2
EXTENDER
IR1 Extender
RS232 Out IR2 Blaster
HDMI Out
IR BLASTER
1.5m
60°
IR EXTENDER
7m
3m 3m
60°
m
Local Display
Smart TV
HDMI
Output
Power
Supply
RS-232 Device to
be controlled
HDMI
Input
RS-232
RS-232
HDMI Output
IR In/Out
CAT5/e/6/7 Output
(up to 60m)
Blu-ray Player or
Games Console
RS-232 Equipped
PC or Notebook
RX

7
8. SPECIFICATIONS
8.1 Technical Specications
Video Bandwidth 300 Mbps/10.2 Gbps
Input Ports 1×HDMI, 1×RS-232, 1×IR IN, 1×USB (Service
only)
Output Ports 1×HDMI, 1×IR OUT, 1×CAT5e/6/7
HDMI Supported
Resolutions
480i~1080p@50/60 Hz, 1080p@24 Hz, 4K×2K
(3840×2160@30 Hz/4096×2160@24/25Hz) &
VGA~WUXGA (RB)
HDMI Input
Cable Distance
10m (1080p@8/12-bit), 5m (4K×2K)
HDMI Output
Cable Distance
15m (1080p@8-bit), 10m (1080p@12-bit),
10m (4K×2K)
IR Frequency 30~50 kHz
Power Supply 24 V/1.25A DC (US/EU standards, CE/FCC/
UL certied)
Dimensions 102 mm(W)×109 mm(D)×25 mm (H)
Weight 244 g
Chassis Material Metal
Color Silver
ESD Protection Human body model:
±8kV (air-gap discharge)
±4kV (contact discharge)
Operating Temperature 0 °C ~ 40 °C
Storage Temperature −20 °C ~ 60 °C / −4 °F ~ 140 °F
Relative Humidity 20 ~ 90 % RH (non-condensing)
Power Consumption 6.3 W

8
8.2 CAT5e/6/7 Cable Specication
CABLE TYPE RANGE PIXEL
CLOCK
RATE
VIDEO
DATA
RATE
SUPPORTED VIDEO
CAT5e/6/7 60 m <=225
MHz
<=5.3 Gbps
(HD Video)
Up to 1080p, 60 Hz, 36
bits, 3D (data rates
lower than 5.3 Gbps or
below 225MHz TMDS
clock)
40 m >225
MHz
> 5.3 Gbps
(Ultra HD
Video)
4K×2K, 30Hz video
formats
9. ACRONYMS
ACRONYM COMPLETE TERM
4Kx2K 3840x2160 / 4096x2160
DTS Digital Theater System
EDID Extended Display Identication Data
HDCP High-bandwidth Digital Content Protection
HDMI High-Denition Multimedia Interface
HDTV High-Denition Television

Home page: http://www.cypress.com.tw
CYPRESS TECHNOLOGY CO., LTD
20130531MPM-CHDBT-1H1CL