Shinybow USA SB-3706 User manual
INSTRUCTION MANUAL
SB-3706
1x8 Video Distribution Amplier (RCA)
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your
equipment. Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain,
water and excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean
dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and
plugs, convenience receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken
so that the means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper
AC voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may
impede the normal ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used
in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all
servicing to qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting
cables to other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship
the unit, use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY
INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.
1
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power
supply. Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re, electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage
parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow
for sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for
any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means — electronic, mechanical, magnetic, optical, chemical,
manual, or otherwise — without the express written permission and consent.
© Copyright 2020. All Rights Reserved.
Version 2.2 APR 2020
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
www.shinybowusa.com
122 Rose Ln. Suite 303 | Frisco, Texas 75036
2
INTRODUCTION / FEATURES / CONTENTS.................................................................................2
SPECIFICATIONS............................................................................................................................3
TYPICAL HOOKUP & OPERATION.................................................................................................4
INTRODUCTION
Composite Video Distribution Amplier Series
Thank you for purchasing the SB-3706 RCA Composite Video (8) Way Distribution Amplier. You will
nd this unit easy to install and highly reliable but it is essential that you read this manual thoroughly
before attempting to use this amplier.
Congratulations on your purchase of the SB-3706 Composite Video Signal Distribution Amplier.
The SB-3706 is a compact composite video distribution amplier that supports (8) outputs composite
video outputs that are identical to the source signal. Ideal for distributing video signals from DVD,
Video Game Console, Satellite Receivers, Cable/Satellite Box, etc. up to (8) screens. The SB-3706
composite splitter is designed to support high resolution video for up to 200 ft output cable runs.
FEATURES
• Maintains high resolution video signal over long distance output cables
• All Outputs are mirrored
• Buffered Input and amplied Outputs
• Supports high resolution video signals up to 200ft
• Gold plated RCA jacks
• Supports PAL and NTSC signals
• Optional rack mount kit
PACKAGE CONTENTS
Check that you have the following components;
• SB-3706 (RCA) Amplier
• Video Cable (RCA-RCA Connector)
• AC/DC Adapter: 12VDC@420mA AC/DC Adaptor Types: CE/UL/SAA/BS
• Users Guide
TABLE OF CONTENTS
3
SPECIFICATIONS
• Type of Amplier: 1x8 Composite Video Distribution Amplier
• Input Video: (1) RCA (female) Composite Video 75Ohms, 1Vpp
• Output-Video: (8) RCA (female) Composite Video 75Ohms, 1Vpp
• Video Bandwidth: 110MHz (-3dB) (G =/+1)
• Video Amplier Bandwidth: 250MHz
• Audio Frequency Response: 20Hz~20KHz, +0.05dB
• Scan Rate: 50Hz/60Hz
• Settling Time: 50ns to 0.1%
• Low Power: 4.4mA / Amplier
• Low Distortion: -80dBk total harmonic @1MHz, RL= 100Ž½
• Slew Rate: 1000V/as
• Gain Flatness: 0.1dB to 20MHz, RL=150%
• Differential Gain Error: 0.03%, RL=1k%
• Differential Phase Error: 0.03%, RL= 1k%
• In/Out Terminal: RCA connectors
• Enclosure Type: Metal case
• Power Consumed: 200mA Max
• Power Supply: DC 12 Volts@420mA
• Dimensions (LxWxH): 6.93 x 3.14 x 1 in (176x80x25mm)
• Weight: 1.0 lb (Unit only) / 1.3 lb (Net) / 2 lb (Shipping)
As product improvements are continuous, specications are subject to change without notice.
4
TYPICAL HOOKUP AND OPERATION
Inputs: (1) Composite Video (RCA)
Outputs: (8) Composite Video (RCA)
DC Input: 12V@420mA
Power SW: On/Off
Safeguards and Precautions
A. Keep this unit away from re, extremely hot areas, water or moisture of any kind.
B. Do not place this unit on any support that is not rm, level and strong.
C. Do not service the unit yourself. Opening the unit’s housing will void the warranty.
D. Servicing must be by Shinybow or by an authorized technician.
C. Illegal duplication of copyrighted material is strictly prohibited by Federal Laws.
CONFORMANCE TEST REPORT
FOR EN 55013 / EN 55020 - REPORT NUMBER: ET93S-06-168-1EN 55013 / EN 55020 - REPORT NUMBER: ET93S-06-168-1
FOR FCC 47 CFR / Part 15 Subpart B - FCC 47 CFR / Part 15 Subpart B - REPORT NUMBER: ET93S-06-168-02
Model Number: SB-3706
Comment Number: SB-3704, SB-3705, SB-3706, SB-3708, SB-3709, SB-3710, SB-3714,
SB-3716, SB-3730, SB-3733, SB-3737
Input: Composite Video (RCA Connector)
Output: (8) Composite Video (RCA Connector)
Power Supply: +DC12V@420mA
TYPICAL HOOKUP AND OPERATION
8X COMPOSITE VIDEO DISTRIBUTION AMPLIFIER
Composite Video System: RCA Connector
5
LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using or installing the product, you unconditionally signify your agreement
to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the product and return the product to SHINYBOWUSA, Inc. at the return
address set forth on the product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime, without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the product. You
are authorized to use the product solely in connection with such instructions. Any use of the product not in accordance with such instructions shall void any warranty
pertaining to the product. Any and all damages that may occur in the use of the product that is not strictly in accordance with such instructions shall be borne by you
and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the product are
licensed to you by SHINYBOWUSA, Inc. and/or its afliates, including any manufacturers or distributors of the product (collectively, “SHINYBOWUSA”) for your personal
use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the product.
The product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the product and SHINYBOWUSA retains full and complete title to the intellectual
property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the product, and you may not copy or use them in any
manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
The functionality and usability of the product is controlled by SHINYBOWUSA, Inc. from its ofces within the State of Texas, United States of America. SHINYBOWUSA
makes no representation that materials pertaining to the product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
SHINYBOWUSA may change or modify the product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the product and, therefore, such information or statements should not be
relied upon as being current as of the date you use the product. Moreover, any portion of the materials pertaining to the product may include technical inaccuracies or
typographical errors. Changes may be made from time to time without notice with respect to the product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST OF
ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY
SHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL
DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF
SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL SHINYBOWUSA’S
TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT
YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
Table of contents
