D-Link DVG-G1402S - Wireless Broadband VoIP Router User manual

Before You Begin
DVG-G1402S
Wireless VoIP Route
r
This product can be setup using
any current web browser, i.e.,
InternetExplorer6orNetscape
Navigator 6.2.3.
1. If you purchased this Router to share your high-speed Internet connection with other
computers, you must have an established Internet account from an Internet Service
Provider (ISP).
2. It’s best to use the same computer that is connected to your router for configuring the
DVG-G1402S Wireless VoIP Router. The DVG-G1402S acts as a DHCP server and
will assign all the necessary IP address information on your network. See the Quick
Installation Guide or the Manual on the CD-ROM for setting each network adapter to
automatically obtain an IP address.
©2005 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of
their respective holders. Software and specifications subject to change without notice. DVG-G1402S
Wireless VoIP Router
Check Your Package Contents
•DVG-G1402S
shown with antenna
•CD-ROM
containing Manual and Warranty
•Ethernet Cable
(CAT5 UTP Straight-Through)
Using a power adapter with
a different voltage rating will
damage and void the
warranty for this product.
•12V, 1.2A
Power Adapter
If any of the above items is missing, please contact your reseller.

2
Connecting the Router to your Computer
Reset
Push to return to
factory settings
LAN Ports
Connect to the
LAN and other
computers
WAN Port
Connect to the
WAN (Internet)
Connect to your phones
using standard phone
cabling
Phone Connections
A
ntenna
Ensures good
wireless reception
Power Input
Connect to AC
Adapter
A. First, connect the power adapter to the power input at the back
panel of the DVG-G1402S and then plug the other end of the
power adapter to a wall outlet or power strip. On the front of the
device, the Power LED will turn ON to indicate proper operation.
B. Insert one end of the Ethernet cable into an Ethernet (LAN) port
on the back panel of the DVG-G1402S and the other end of the
cable to an Ethernet Adapter or available Ethernet port on your
computer.
C. Insert one end of the Ethernet Cable (blue) to the LAN or
Ethernet port on your Cable or DSL modem, and then connect
the other end of the cable to the WAN port of the DVG-G1402S.
D. Check the LED display on the front of the Router to confirm that
the connections have been made.
Configure IP Settings
To connect to the network, make sure the network adapter in
your computer is configured properly. Here’s how to configure
the network adapter to obtain an IP address automatically for
the DVG-G1402S Wireless VoIP Router.

For Microsoft Windows XP
Go to Start > select
Settings > click
Control Panel >
Double-click on the
Network
Connections icon
Double-click on
Network Connections
Right-click the
Local Area
Connection icon,
and then select
Properties.
Select Properties
3

The dialog box displays a list
of currently installed network
items.
4
Click Internet Protocol
(TCP/IP)
Make the choice to get the IP
settings assigned automatically.
Select Obtain an IP address
automatically
Click OK
Click Properties

5
Connecting Additional Computers
to the DVG-G1402S
Wireless VoIP Router
Using additional Ethernet (CAT5 UTP) cables, connect your Ethernet-
equipped computers to the LAN ports on the back panel of the DVG-
G1402S.
When you have completed the steps in this Quick Installation Guide,
your connected network should look similar to this:

Initial Web Configuration
6
Open your Web browser and
type http://192.168.15.1 into
the URL address box. Press
EnterorReturn.
The login dialog box
appears:
When you first log in, the
User name is admin and
the Password is also
admin. These may be
changed later.
Click OK.

The Home window appears:
Click Run Wizard.
Clicking a hyperlink on the menu on the upper left side of the window
brings up a detailed configuration window (see the next section for a brief
description of three typical WAN connection examples).
7

Configuring the Router using
the Setup Wizard
The following screens are displayed when you click Run Wizard from the
Web configuration Home page, as shown above. Included are typical
WAN (Internet) connection examples for Dynamic IP Address (DHCP),
Static IP Address, or PPPoE connections. Click Run Wizard on the
menu above to view the following Wizard window:
Click the Next button.
8

Click the Next button.
Enter the Time Zone that corresponds to your location on the
planet.
Click Next to continue.
9

Click the Next button.
Enter the WLAN channel and SSID you want to use for your
WLAN network. Initially, you can accept the default values
and change the router’s configuration later.
Click Next to continue.
10