D-MAX DIC-5830DV User manual

IR Vandal Dome Camera
사용 설명서
용서
DIC-5830DV
650TVL, D-FOG
MANUAL

2
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform
to all local codes

3
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time,
fire may be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
■ Warning

4
1.Features --------------------------------- 6
2. Cable Connection & OSD Control --------------------------------- 7
3. Setup Menu Operation --------------------------------- 8
4. Troubleshooting --------------------------------- 19
5. Dimensions --------------------------------- 20
6. Specifications --------------------------------- 21
■Contents

☺Ultra High Resolution 650 TV Lines
Clear image quality has been achieved by employing a double-speed SONY CCD with
410,000(effective) pixels, which provides a horizontal resolution of 650 TV lines.
☺Visual Distance & Smart IR
It is 0.1lux at color mode and its LED will be lit at lower light enabling that observer could
see object in the distance of 30M.(visible distance 30M)
In addition, the Smart IR feature protects saturation when object is too close to the camera.
☺Electrical Day & Night (True Day & Night)
The camera identifies whether it is day or night and automatically switches to the
appropriate mode, depending on its environment. By day, the camera switches to color
mode in order to maintain optimal color. At night, it switches to B/W mode so as to obtain
better picture definition.
☺F-DNR(Defog)
This camera supports Defog function which does a process of clearing blurred image
caused by fog and snow by analyzing the brightness of input image and compensating
Color of the image.
☺Coaxial cable communication
This is a remote control function that uses the coaxial cable with the control signal. And
this helps you control the camera’s condition what you want without additional cabling in
installation or repair.
☺Motion Detection
Since the camera detects motion and generates signals without any additional external
sensors, you can monitor activity more efficiently by connecting the camera to an alarm
device.
☺White Defect restoration
When the camera has white defect in the CCD with ages, User can restore it.
☺D-WDR
Built-in Digital WDR
☺SMART 3D-DNR
The high performance New DSP chip dramatically reduces the gain noise in digital image
processing, producing clear, sharp images in low lighting environment. Especially It will be
operate 3D DNR mode before happening motion, but if there is motion, it will be change
smart 3D DNR mode.
☺Additional Functions
HSBLC, DIS, OSD, FREEZE, Mirror(H,V-FLIP,ROTATE), D-ZOOM, Negative Image,
Sharpness, Privacy functions.
1. Features

6
1) Cable Connection
( DC12V Type )
(Dual Type DC12/AC24V)
2) OSD Control
① 3AXIS BRACKET
- Please loosen screws and fix tilted and panned position.
③ LENS : Vari-Focal Auto Iris Lens ( 2.8mm ~ 12.0mm / F1.2 ) with ICR OSD PCB
- SETUP button : Used for the menu display. This button can be used to confirm settings
after changing the value of the selected function or current conditions.
- UP & DOWN buttons : Used for selecting items by moving the cursor up or down on the
menu screen.
- LEFT & RIGHT buttons : Used when changing item values, by moving the cursor to the
left or right on the menu screen
2. Cable Connection & OSD Control

7
• Menu Structure
LENS DC / VIDEO / MANUAL
EXPOSURE SHUTTER AUTO / FLK / MANUAL / 1/60
AGC LOW / MIDDLE / HIGH / OFF
SENSE-UP AUTO / OFF
RETURN
BACK LIGHT OFF / DWDR / BLC / HSBLC
WHITE BAL ATW / AWB / AWC-SET / MANUAL
DAY & NIGHT AUTO / EXT / NIGHT / COLOR
SMART 3DNR OFF / ON
F-DNR OFF / MANUAL / AUTO
FUNCTION MOTION OFF / ON
PRIVACY OFF / ON
D-EFFECT D-ZOOM / SAMART ZOOM / DIS / PIP /
FREEZE / MIRROR / NEG. IMAGE
IMAGE ADJ SHARPNESS / MONITOR / LENS SHADING
/ DEFECT
COMM ADJ CAM TITLE
SYNC
LANGUAGE
RETURN
EXIT SAVE / CANCEL / RESET
① Please press the SETUP button Settings can now be made. The SETUP menu is
displayed on the monitor.
②Please select any function you wish to activate by using the UP and DOWN buttons.
- The arrow can be moved up or down by using the UP and DOWN buttons.
- Please position the arrow to point to the function you wish to operate.
or RIGHT button if you
③ Please press the LEFT
3. Setup Menu Operation
Select any function you
wish to operate by using
the UP and DOWN
buttons.
Modes can be changed
using the LEFT and
RIGHT buttons.
MAIN MENU
1.LENS DC↙
2.EXPOSURE ↙
3.BACKLIGHT OFF
4.WHITEBAL ATW
5.DAYNIGHT AUTO
6. SMART 3DNR OFF
7. F-DNR OFF
8. FUNCTION ↙
9.EXIT ↙

8
wish to change mode.
When the LEFT or RIGHT button is pressed, available values and modes are displayed
in order. Please keep pressing the button until you get to the mode you wish to operate.
④Please select 'EXIT' and then press the SETUP button to finish the setting.
Note)
• If arrow appears at the mode you wish to operate, it means that there is a sub-menu
which can be selected by pressing the SETUP button.
• If arrow appears at the mode item, it means that there is no mode available to be
selected.
1. LENS
This function is used to select the type of lens.
DC: Select this mode in case of using DC type lens and control brightness value at the
sub-menu.
▶BRIGHTNESS: Adjust the screen brightness
▶IRIS SPEED: Adjust iris speed
MANUAL: Select this mode in case of using manual lens and control brightness value at
the submenu.
▶BRIGHTNESS: Adjust the screen brightness
VIDEO: Select this mode in case of using Video lens.
2. EXPOSURE
This function is used to adjust EXPOSURE
SHUTTER: Select shutter speed.
The default value is AUTO.
▶AUTO, FLK, MANUAL, 1/50
AGC (Auto Gain Control)
▶ LOW / MIDDLE / HIGH
SENS-UP (Digital slow shutter)
▶OFF / AUTO (x2~x256)
3. BACK LIGHT
This function is used to view a picture more clearly under back light condition.
▶BLC
Enable a user to directly select a desired area from a picture, and to view the area more
clearly.
VALUE: Select BLC value.
EXPOSURE
▶SHUTTER AUTO
AGC HIGH
SENSE-UP ON↙
RETURN RET↙
BLC
▶1.VALUE MIDDLE
2.AREA SINGLE↙
3.DEFAULT ↙
4.RETURN RET↙
DC LENS
▶1. BRIGHTNESS IIIIIIIIIII 1~100
2. IRIS SPEED IIIIIIIIIIIII 1~5
RETURN RET↙
DC LENS
▶1. BRIGHTNESS IIIIIIIIIII 1~100
RETURN RET↙

9
•LOW / MIDDLE /HIGH
AREA: Select area and then adjust size and position of the area.
DEFAULT: Initialize all data you set.
▶DWDR
When there are both bright and dark areas at the same time, this mode makes both areas
distinctive.
LOW LEVEL: Set lower level (0~15)
HIGH LEVEL: Set High level (0~15)
▶HSBLC
GAIN: select gain value.
MODE: select between night only mode and all day
mode
MASK LEVEL: select mask level.
DEFAULT: Initialize all data you set.
M.SKIP AREA: set exception area where HSBL
MASK doesn’t work.
4. WHITE BALANCE
The screen color can be adjusted by using the WHITE BALANCE function.
▶ATW: Select this when the color temperature is between 2,000°K and 9,000°K
▶AWB: this mode doesn’t have the color temperature range.
▶AWC->SET: To find the optimal setting for the current luminance environment
in this mode, put the camera towards a sheet of white paper.
▶ MANUAL: Select this to fine-tune White Balance
manually. Set White Balance first by using the ATW
or AWB mode. After that switch to MANUAL mode,
fine-tune the White Balance.
Note)
• Under the following conditions the WHITE BALANCE function may not operate properly.
In such cases, please select the AWB mode.
When the object’s surroundings have a very high color temperature such as a clear sky.
When the object’s surroundings are dark, If the camera directly faces a fluorescent light or
is installed in a place where there are considerable changes in illumination, the WHITE
BALANCE function may become unstable.
5. DAY&NIGHT
You can display pictures in color or B/W.
DWDR
▶1. LOW LEVEL IIIIIIIIII 0~15
2. HIGH LEVEL IIIIIIIIIII 0~15
3. RETURN RET↙
HSBLC
▶1. GAIN IIIIIIIIIII 1~100
2.MODE NIGHTONLY
3. MASK LEVEL IIIIIIIIII 1~100
4.DEFAULT ↙
5. M. SKIP AREA OFF
6. RETURN RET↙
MANUAL WD
▶1. BLUE IIIIIIIII 1~100
2. RED IIIIIIIII 1~100
3. RETURN RET↙

10
Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
▶ COLOR: The picture is always displayed in color.
▶ AUTO: The mode is switched to ‘Color’ in a normal environment, but switches to ‘B/W’
mode when ambient illumination is low.
- DELAY: adjusting converting speed for COLOR ↔
BW
- D→N: user can adjust luminous level to convert
from Day to Night.
- N→D: user can adjust luminous level to convert from
Night to Day.
▶EXT: This mode allows you to apply a desired filter
to external signals.
▶ B/W: This mode allows you to apply a desired filter
to external signals.
BURST: If it cannot be synchronizing video on the
monitor in the BW mode of camera, it turns on.(When
the camera in B/W mode, the WHITE BALANCE is
deactivated.) If DAY NIGHT mode is AUTO, the AGC is fixed HIGH.
IR LED: if you use IR LED, select On mode.
IR SMART: When the IR camera is used, this function can suppresses saturation of the
picture that happens in the short distance from object and you can set area up that you
want.
6. SMART 3DNR
This function reduces the background noise in a low luminance environment.
It will operate 3D DNR mode before happening motion, but if there is motion, it will
change to smart 3D DNR mode.
▶ON: Activates 3DNR so that noise is reduced. Set the 3DNR mode to ‘'ON’' and press
the SET button. Then you can adjust the noise reduction level.
▶OFF: Deactivates 3DNR. Noise is not reduced.
VALUE: adjust 3 DNR level
SMART NR: if you want to use SMART 3D DNR,
select ON mode.
SMART LEVEL: adjust SMART 3D DNR level
SENSIVITY: adjust sensitivity level
D&N AUTO
▶DELAY IIIIIIIIIIIIIIIIII 0~15
D→N IIIIIIIIIIIIIIIIIII 16~249
N←D IIIIIIIIIIIIIIIIIII 1~233
RETURN RET↙
D&N NIGHT
▶BURST OFF
IRSMART OFF
IRLED ON
RETURN RET↙
D&N EXT
▶DELAY IIIIIIIIIIIIIIIIIIIII 0~15
RETURN RET↙
SMART 3DNR
1. VALUE IIIIIIIIII 0~200
2.SMARTNR ON
3. SMART LEVEL IIIIIIII 0~200
4. SENSITIVITY IIIIIIIII 0~100
RETURN RET↙

11
7. F-DNR (Defog)
This camera supports DEFOG function which does a process of clearing blurred image
caused by fog and snow by analyzing the brightness of input image and compensating the
color of the image
▶OFF: Deactivates F-DNR.
▶F-DNR MANUAL
This function is operated manually
LEVEL: Select level
▶F-DNR AUTO
This function is operated automatically.
LEVEL: select level
F-DNR OFF F-DNR ON
8. FUNCTION
1) MOTION
Motion detection function allows more effective observation. When any movement is
detected, signal is generated
▶ON: If ‘MOTION’ function is active, character of person is flickering on right above
position when motion is detected on selected area.
F-DNR MANUAL
1. LEVEL IIIIIIIIIIIII1~ 5
2. DUMMY IIIIIIIIIIIII1~ 10
3. DUMMY IIIIIIIIIIIII1~ 10
4GAMMA 0.1~1
5.RETURN RET↙
F-DNR AUTO
1. LEVEL IIIIIIIIIIIII 1~5
2.RETURN RET↙
FUNCTION
1.MOTION OFF
2.PRIVACY OFF
3.D-EFFECT ↙
4.IMAGEADJ ↙
5. CAMERA TITLE OFF
6.SYNC INT
7. LANGUAGE ENGLISH
8. RETURN
Select any function you
wish to operate by using
the UP and DOWN
buttons.
Modes can be changed
using the LEFT and
RIGHT buttons.

12
AREA: Select the programmed area that can be set up
to 4 areas.
AREA DISPLAY: Turn on and off the programmed
motion area.
VALUE: Adjust motion sensitivity of the programmed
motion area.
MOTION VIEW: Turn on and off the display when
motion detected.
▶OFF: Cancel Motion detection function.
2) PRIVACY (POLYGON)
You may conceal specific area on the screen with this ‘PRIVACY’ function.
AREA: Select the programmed privacy area (Area 1~8)
AREA DISPLAY: Turn on and off the programmed
privacy masking.
Set position and area size for privacy masking using
arrow
COLOR: Setup color of the programmed motion area
mask (1-15 color)
TRANSPAR: select color transparency.
3) D-EFFECT
D-ZOOM: You can use a digital zoom (256x).
- PAN: Moving zoom-in picture to left-right
- TILT: Moving zoom-in picture to up-down
* It doesn’t work for PAN. TILT when the D-ZOOM is
on x1.0.
SMART ZOOM: When motion is detected, SMART
ZOOM will be operated to preset point automatically.
DIS(Digital image stabilizer):Protect against camera shake
PIP(Picture in picture): When using digital zoom, you can view wide scene without digital
zoom on the monitor.
FREEZE: You can view still or moving pictures.
MIRROR: You can flip the picture
- MIRROR: Horizontal reverse pictures on the monitor.
- V-FLIP: Vertical reverse pictures on the monitor.
- ROTATE: diagonal reverse pictures on the monitor (180° rotation)
NEG. IMAGE: Switching to negative color.
4) IMAGE ADJ
MOTION
1.AREA 1
2. AREA DISPLAY ON↙
3. VALUE IIIIIIIIIII 0~100
4.MOTIONVIEW ON
5. RETURN
PRIVACY
1.AREA 1
2. AREA DISPLAY ON↙
3. COLOR IIIIIIIIIII 0~15
4. TRANSPAR IIIIIIIIIII 0~3
5. RETURN
D-EFFECT
1.D-ZOOM ON↙
2.SMARTZOOM ON↙
3.DIS OFF
4.PIP OFF
5.FREEZE OFF
6.MIRROR OFF
7.NEG.IMAGE OFF
8. RETURN

13
SHARPNESS: Adjust sharpness of the video picture
MONITOR: Select the kind of the monitor (LCD / CRT)
OSD COLOR: User can select OSD color
▶CRT: Select this menu when using a CRT monitor.
- PED LEVEL: Adjust PED level.
- COLOR GAIN: Adjust COLOR GAIN
▶LCD: Select this menu when using a LCD monitor
- GAMMA: Adjust GAMMA level
- PED LEVEL: Adjust PED level.
- COLOR GAIN: Adjust COLOR GAIN
LENS SHADING: When setting the zoom to maximum and Lens angle of view are
saturated on screen, set ON to make the Lens edge invisible.
It might happen only if fluorescent light is shined fully on screen.
DEFECT: When the camera has white defect in the CCD with ages, user can restore it
using OSD menu.
- Sense-up: User can adjust white defect according to luminous condition.
- DIFF: User has to select level(1~4) according to size of the white defect. If it is big, you
have to select high number
- START: Before pressing the Start menu, you have to cover camera lens using lens cap
5) CAMERA TITLE
If the TITLE is input, the camera TITLE appears on the monitor.
Select an ID from A,B~Y,Z, 0,1~8,9.
Note) If the wrong name has been input.....
• If you press the SETUP button after moving the
cursor to CLR, all the letters will be erased. If you want
to correct a letter, please move the cursor to the arrow
at the bottom left of the screen and press 'SET'.
• Please position the cursor above the letter you wish
to correct, and then move the cursor on to the letter
you wish to choose and press the SETUP button.
• When a name has been chosen, please select a position for the name display.
▪Please move the cursor onto 'POS' and then press the SETUP button.
▪ The name will appear at the top left corner.
▪Please find the position you wish to display the name in by using the 4 directional
buttons,
and then press the SETUP button.
▪Please select 'END' and then press the SETUP button to complete ID input.
6) SYNC
In areas where the supply is at 60Hz/NTSC (50Hz/PAL), you can synchronize the output
IMAGE ADJ
1. SHARPNESS IIIIIIIII 0~31
2.MONITOR CRT↙
3. LENS SHADING ON↙
4.DEFECT ↙
5. RETURN

14
phase of multiple cameras using the power synchronization
function (Line-Lock) without using a synchronization signal generator.
•INT : Internal Synchronization Type
•L/L : Power Synchronization Type, Line-lock
Press the SET button and you can select a desired phase between 0 and 359.
synchronization.
• When the power is DC 12V, the menu is fixed to the ‘INT’ mode.
7) LANGUAGE
It can be switched to English, Korean, Polish, Turkish, Hebrew, Arab, Russian, French,
Spanish, Italian, Portuguese, German, chinese, Japanese on OSD menu.

15
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
• Nothing appears on the screen.
- Check that the power cord and line connection between the camera and monitor are
fixed properly.
- Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
• The image on the screen is dim.
-Is lens stained with dirt? Clean your lens with soft, clean cloth.
-Set the monitor to proper condition.
-If the camera is exposed to too strong light, change the camera position.
• The image on the screen is dark.
-Adjust the contrast feature of the monitor.
- If you have an intermediate device, set the 75Ω/ Hi-z properly.
• The camera is not working properly, and the surface of the camera is hot.
-Check that you have properly connected the camera to an appropriate power source. •
• The Motion Detection function does not work.
-Check that MOTION DET of SETUP menu is ‘OFF’.
• Color is not correct.
-Check the setting of WHITE BAL SETUP menu.
• The screen flickers continually.
-Check that direction of camera turns toward the Sun.
• When coaxial communication is not available:
- Make sure that the camera and monitor are installed within the recommended distance.
-Use the video amplifier equivalent to coaxitron if the recommended installation distance
is exceeded.
• IR-LED isn't lighted.
-Isn't DAYNIGHT function setting up the color mode.
-Please change the AUTO or B/W mode.
4. Troubleshooting

16
5. Dimensions

17
▪GENERAL
Signal system NTSC PAL
Image Sensor 1/3” Sony HAD CCD∥
Total Pixels 811(H) Χ508(V) 795(H) Χ596(V)
Effective Pixels 768(H) Χ494(V) 752(H) Χ582(V)
Resolution 650 TV lines (B/W 0Lux)
Scanning Frequency 15.734KHz(H), 60(V) 15.625KHz(H), 50(V)
Shutter Speed 1/60 ~ 1/100,000 sec 1/50 ~ 1/100,000 sec
Min.
Illumination
IR LED ON 0 Lux
IR LED OFF 0.00001Lux (Sens-up 256x)
IR LED Range Max. 30M (LED :30 PCS)
Day & Night EXT / B/W / Color / Auto
Digital WDR On / Off
Digital Zoom X32
White Balance ATW / AWB / AWC-Set / Manual
BackLight OFF / BLC / HSBLC
AGC Low / Middle / High / Off
Defect / DIS On/ Off
F-DNR On /Off
Coaxial Communication Available
3D-DNR On / Off
Privacy Zone / Motion Detection 8 Area / 4 Zone
Sharpness 0 ~ 31
S/N Ratio More than 52dB
Video Output Composite video output 75 ohm terminated
Lens 2.8~12.0mm Auto Iris Lens ( True Day & Night with ICR ), F1.2
Sync. System Internal
Operating Humidity 30 % ~ 90 % RH
Operating Temp. - 10°C to 50°
Install Type Outdoor (IP66)
Dimension φ100(Bubble) x 107.5(H)mm
Material PC Bubble, Aluminum Body
Weight 1.1Kg
Power Consumption Max 5W (LED On)
Power Supply DC 12 V 1A(10.2V~14.5 V), Dual Voltage (Option):AC24V / DC12V
6. Specifications