Dacor PCOR30S User manual

Part No. 107002 Rev. D
Installation Instructions
PCOR30S
Over The Range Convection
Microwave Oven
Ventilation System (Preparing Oven for Installation)...4
Oven Installation
................................................... 6
Mounting Plate................................................... 6
Mounting Oven to the Wall .................................. 6
Mounting Deflector 8
Befor You Begin
.................................................. 1
Mounting Space
.................................................. 1
Wall Construction
.............................................. 1
Electrical Grounding Instructions
............................ 2
Hood Exhaust Duct
............................................. 2
Tools Recomended for Installation
......................... 3
Installation Hardware
.......................................... 3
Check List for Installation .......................................8
..............................................
Ta ble of Contents
TINSEB319MRR1

1
Please read all instructions thoroughly before installing the over the range microwave oven/hood system. Two
people are recommended to install this product.
If a new electrical outlet is required, its installation should be completed by a qualified electrician before the over
the range microwave oven/hood system is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.
This microwave oven/hood requires a mounting space on
a wall as shown in Figure 1. It is designed to be used with
standard 12-inch wall cabinets.
Consult the installation instructions for the range or cooktop
being installed for additional and/or superseding minimum
distance requirements.
2 WALL CONSTRUCTION
Figure 1
At least 2"
15.5"
30"
Backsplash
12"
66" or more
from floor
30" or more from
cooking surface
Before You Begin...
1 MOUNTING SPACE

2
3 ELECTRICAL GROUNDING INSTRUCTIONS
This appliance must be grounded. This oven is equipped with a cord having a grounding wire with a grounding plug. It must be
wire for the electric current.
WARNING - Improper use of the grounding plug can result in a risk of electric shock.
Electrical Requirements
etarapesaotdetcennocebtsumgulpdnadrocylppusrewopehT
receptacle. The receptacle should be located inside the cabinet directly
above the microwave oven mounting location as shown in Figure 2.
1. If you have any questions about the grounding or electrical instruc-
oven or personal injury resulting from failure to observe the correct
electrical connection procedures.
4 HOOD EXHAUST DUCT
-
Exhaust connection:
Maximum duct length:
transitions and adapters plus the length of all straight duct sec-
Figure 3
Figure 2
Ground
Receptacle
Opening for
Power Cord

3
• Phillips screwdriver
(if metal cabinet is used)
(if needed)
• Protective drop cloth for product and
range - you may also use carton for
protection
• Pencil
• Tape measure
• Tape
Figure 4
Parts shown not to common scale.
ITEM NAME QUANTITY
1
2
3
4
5
6
7
8
9
The installation hardware (items 1- 8
5 TOOLS RECOMMENDED FOR INSTALLATION
6 INSTALLATION HARDWARE
-
top cabinet template
1 5
6 7
2 3 4
8
9

4
7 VENTILATION SYSTEM (PREPARING OVEN FOR INSTALLATION)
your installation.
Vertical Exhaust
Horizontal Exhaust
Recirculating
(A) VERTICAL EXHAUST: OUTSIDE VENTILATION
outercase cabinet by sliding it into the slits in the same direc-
(B) HORIZONTAL EXHAUST: OUTSIDE VENTILATION
-
operation.
Figure 6 Figure 7
Fan Cover Bracket Hood Fan Unit
Exhaust Damper Assembly
Figure 5

5
Figure 8 Figure 9
Figure 10
(C) RECIRCULATING: Non-Vented, Ductless Operation
as shown in Fig. 6.
blades should be visible through the openings facing toward
the front of the oven.
again.
-
CHARCOAL FILTER
by unplugging.
3. Pull the louver away from the oven.
hand and replace the 2 screws to secure louver.
Hood Fan Unit
Fan Cover Bracket
Mounting Plate
(back side)
Figure 11
Louver
Oven light
Charcoal filter
Screw
Screw

6
Top Side
Cutting Line
Figure 16
(A)
(B)
Figure 15
MOUNTING OVEN TO THE WALL
Mounting
Plate
Figure 12 Figure 13 Figure 14
Wall
8 OVEN INSTALLATION
-
MOUNTING PLATE
-
3. Position the mounting plate with the toggle bolts attached at the wall location and insert toggle nuts and bolts through the
open on the other side of the wall. Also, once a toggle nut opens, it cannot be withdrawn from the hole; therefore make
sure all of the toggles are in the correct position before insertion.
-
Toggle Nut
Toggle Bolt Space more than
wall thickness

7
Figure 17
C
D
Figure 18
Figure 19 Figure 20
Figure 21
Mounting Screws
Grommet (for metal
cabinet only)
Hang at
these
locations
(B)
(B)

8
CHECKLIST FOR INSTALLATION
2. Plug in the power cord.
3. Keep the use and care manual.
MOUNTING DEFLECTOR
DEFLECTOR

9
Notes