Daewoo electricals QI User manual

1
QI Wireless Charging Alarm Clock

2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be followed. These instructions should be saved for future
reference:
•Read and familiarise yourself with all operating instructions before
using this Alarm Clock.
•Before plugging your unit into the USB supply, visually check that the
unit is intact and has not suffered any transit damage.
•Check that the voltage indicated on the data plate corresponds with
that of the local network before connecting the appliance to the
mains power supply.
•Always use this appliance on a solid, level, non-flammable surface.
•Ensure that there is clearance of at least 100mm (4 Inches)
minimum around the Alarm Clock for sufficient ventilation.
•Ensure that the ventilation openings are not covered with items,
such as newspapers, table-cloths, curtains, etc.
•No naked flame sources, such as lighted candles, should be placed
on the Alarm Clock.
•Do not position the Alarm Clock close to sources of heat such as
radiators, heaters, other electronic equipment, etc.
•The Alarm Clock shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed on
the apparatus.
•Do not immerse the Alarm Clock in water or any other liquids.
•This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be kept away unless
continuously supervised.
•Do not use this Alarm Clock outdoors.
•Repairs to electrical appliances should only be performed by
qualified personnel. Improper repairs may place the user at serious

3
risk.
•Do not operate this appliance after a malfunction or after being
dropped or damaged in any way.
•Do not allow the USB power cable to hang over sharp edges or come
in contact with hot surfaces.
•Do not run the USB power cable under carpets, rugs, etc.
•This product is intended for household use only and should not be
used for industrial purposes.
•Do not use any accessories or attachments with this product other
than those supplied or recommended by supplier.
•Do not use this product for anything other than its intended use.
•Do not push objects into any openings as damage to the product
and/or electric shock may occur.
Description of Parts
1. LED Display.
2. LED Night Lamp button.
3. USB Socket.
4. Wireless Charging Pad.
5. Wireless Charging Indicator.
6. + & - buttons
7. M button.
8. LED Night Lamp.
9. USB Type-C Power Input Socket (rear).
10. USB Power Cable.
11. USB C-Type Plug.
11
10
8
1
5
4
2
7
6
9
3

4
Before the first time you use your Wireless Charging Alarm Clock
Please read these operating instructions thoroughly and keep them in a safe place for future
reference.
Remove all packing materials and discard responsibly.
Operating Instructions
Powering up your Wireless Charging Alarm Clock
1. Insert the USB C-Type Plug (11) of the USB Power cable (10) into the Type-C Power Input Socket (9)
on the rear of the Alarm Clock.
2. Insert the large USB plug on the other end of the USB Power Cable (10) into a suitable USB supply
rated between 5 volts 2 amp and 9 volts 1.67A.
Using Your Wireless Charging Alarm Clock
12 or 24 Hour Mode
1. Press the M button (7) twice to toggle between 12-hour or 24-hour mode, the LED Display (1) will
flash ‘12H’ or ‘24H’ to confirm the mode selected.
Setting the Time
1. Press the Mbutton (7) briefly once and the minutes will flash. Press the + & - buttons (6) to set the
minutes.
2. Press the M button (7) briefly once more. Press the + & - buttons (6) to set the hour.
NB whilst setting the time in 12-hour mode, ensure the AM and PM indicators on the LCD Display (1)
light according to the time set.
Setting the Alarm Time
1. Press and hold the Mbutton (7) for 3 seconds and the minutes will flash. Press the + & - buttons (6)
to set the alarm minutes.
2. Press the M button (7) briefly. Press the + & - buttons (6) to set the alarm hour.
NB whilst setting the time in 12-hour mode, ensure the AM and PM indicators on the LCD Display (1)
light according to the time set.
Setting and Unsetting the Alarm
1. Press and hold the ‘+’ button (6) for 3 seconds to set the alarm. The Alarm icon at the lower centre
of the LED Display (1) will light.
2. Press and hold the ‘-‘ button (6) for 3 seconds to unset the alarm. The Alarm icon at the lower
centre of the LED Display (1) will go out.
Silencing the Alarm
1. After the alarm has sounded simply tap the unit to silence the alarm. The alarm will go into a 5
minute ‘snooze’ period and the alarm icon will flash - alternatively briefly press the ‘-‘or ‘+’
buttons (6) to cancel the alarm.
2. After the alarm has sounded after the snooze period, tap the unit again to silence the alarm for
another 5 minute snooze period and the alarm icon will flash - alternatively briefly press the ‘-‘ or
‘+’ buttons (6) to cancel the alarm.

5
Setting the LCD Display (1) Brightness Level
1. Press the ‘+’ button (6) briefly to increase the brightness the LED Display (1).
2. Press the ‘-‘ button (6) briefly to decrease the brightness of the LED Display (1).
NB At 7.00AM the LED display (1) will automatically default to maximum brightness, at 6.00PM the
display will dim to a lower level and at midnight the display will default to fully dim.
Wireless Charging of your Phone
1. Place your phone on the top of the Charging Pad (4) with the rear of the phone towards the pad.
2. The Wireless Charge Indicator (5) will light blue to show once the phone is fully charged.
NB ensure your phone is compatible with wireless charging in order for it to charge on the unit
wirelessly –also do not use the Charging Pad (4) at the same time whilst the USB Socket (3) is being
used.
Charging Your Phone using the USB socket (3)
1. Insert a USB charging lead (not supplied) into the USB Socket (3) on the Alarm Clock.
2. Connect the other end of the lead to your phone in the normal manner.
NB Only use the USB Charging Socket (3) when the Charging Pad (4) is not being used.
Using the Night Lamp (8)
1. Press the LED Night Lamp button (2) to operate the LED Night Light (8) on the top of the Alarm
Clock. Repeated pressing will step through the different brightness levels of the lamp.
Care and Use of your Wireless Alarm Clock
•Always disconnect the Alarm Clock from the USB supply before cleaning.
•Clean outside of the Alarm Clock with a clean damp cloth. Never clean with harsh or abrasive cleaners.
•Do not submerge the Alarm Clock in water or any other liquids.
Technical Specification
Model Number
AVS1369
Supply Voltage
DC 5V @2A or 9V @1.67A
Wireless Charging Power
10W (max)
USB Output
5V 1A (max)
Unpacked Weight
Approx. 150g
Dimensions (Approx.)
Approx. 75 mm (h) x 140mm (w) x 100mm (d)
Operation temperature
0°C to + 40°C
This product conforms to Radio Equipment Directive 2014/53/EU

6
GUARANTEE
This product is guaranteed for twenty-four months from the date of original
purchase. If any defect should occur due to faulty materials or workmanship, please
return it to the store it was purchased from.
You will need to have your receipt of purchase to hand. The guarantee is subject to
the following provisions:
• It is only valid within the boundaries of the country of purchase.
• The product must be correctly installed and operated in accordance with the
instructions contained in the User Manual.
• The product must be used solely for domestic purposes.
• The guarantee will berendered invalid if the product is re-sold or has been
damaged by inexpert repair.
• The manufacturer disclaims any liability for incidental or consequential damages.
• The guarantee is in addition to, anddoes not diminish, your statutory or legal
rights.
Daewoo Electricals is a registered trademark.
Produced and imported under licence by ESG Ltd
Manchester M3 1JS www.esgltd.com
Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.