DAEWOO ELECTRONICS DSD-800M User manual

Set-Top BOX
ENGLISH
OWNER’S MANUAL
Digital Terrestrial Receiver | DSD-800M
HELP LINE Number ; 0870 100 2525
With queries, please quote the page number, reference number
and model number.
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` A mac001 1200DPI 90LPI

SAFETY INFORMATION
CAUTION: To reduce the risk of fire and
electric shock, do not remove the cover (or
back) of the unit. Refer servicing only to
qualified service personnel.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operation and servicing
instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
The apparatus shall not be exposed to dripping or splashing, and that no
objects filled with liquids, such as vases, shall be place on the apparatus.
In addition to the careful attention devoted to quality standards in the
manufacture of your video product, safety is a major factor in the design of
every instrument. However, safety is your responsibility, too. This sheet lists
important information that will help to assure your enjoyment and proper use of
the video product and accessory equipment. Please read them carefully before
operation and using your video product.
1 Read and Follow Instructions - All the safety and operation instructions
should be read before the video product is operated. Follow all operating
instructions.
2 Retain Instructions - The safety and operating instructions should be
retained for future reference.
3 Heed all Warnings - Comply with all warnings on the video product and in
the operating instructions.
4 Polarization - Some video products are equipped with a polarized
alternating - current line plug. This plug will fit into the power outlet, try
reversing the plug. If the plug still fails to fit, contact your electrician to
replace your obsolete outlet. To prevent electric shock, do not use this
polarized plug with an extension cord, receptacle, or other outlet unless the
blades can be fully inserted without blade exposure. If you need an
extension cord, use a polarized cord.
5 Power Sources - This video product should be operated only from the type
of power source indicated on the marking label. If you are not sure of the
type of power supply to your home, consult your video dealer or local power
company. For video products intended to operate from battery power, or
other sources, refer to the operating instructions.
6 Overloading - Do not overload wall outlets or extension cords as this can
result in a risk of fire or electric shock. Overloaded AC outlets, extension
cords, frayed power cords, damaged or cracked wire insulation, and broken
plugs are dangerous, They may result in a shock or fire hazard. Periodically
examine the cord, and if its appearance indicated damage or deteriorated
insulation, have it replaced by your service technician.
7 Power-Cord Protection - Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the video product.
8 Ventilation - Slots and openings in the case are provided for ventilation to
ensure reliable operation of the video product and to protect it from
overheating. These openings must not the blocked or covered. The
openings should never be blocked by placing the video product on a bed,
sofa, rug, or heat register. This video product should not be placed in a
built-in installation such as a book case or rack, unless proper ventilation is
provided or the video product manufacturer's instructions have been
followed.
9 Attachments - Do not use attachments unless recommended by the video
product manufacturer as they may cause hazards.
10 Water and Moisture - do not use this video product near water for example,
near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement,
or near a swimming pool and the like. Caution: Maintain electrical safety.
Powerline operated equipment or accessories connected to this unit should
bear safety certification mark on the accessory itself and should not be
modified so as to defeat the safety features. This will help avoid any and
should not be modified so as to defeat the safety features. This will help
avoid any potential hazard from electrical shock or fire. If in doubt, contact
qualified service personnel.
11 Accessories - Do not place this video product on an unstable cart, stand,
tripod, bracket, or table. The video product may fall, causing serious injury
to a child or adult as well as serious damage to the video product. Use this
video product only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer's or sold with the video product. Any mounting of the
product should follow the manufacturer's instructions and use of a mounting
accessory recommended by the manufacturer.
Note to CATV system installer
This reminder is provided to call the CATV system installer's attention to
Section 820-40 of the NEC which provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as
practical.
12 Outdoor Antenna Grounding - If an outside antenna or cable system is
connected to the video product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Section 810 of the National Electrical Code,
ANSI/NFPA No.70- 1984 (Section 54 of Canadian Electrical Code, Part1)
provides information with respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna-discharge
unit, connection to grounding electrodes, and requirements for the
grounding electrode.
13 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines, other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching or
approaching such power lines or circuits, as contact with them might be
fatal. Installing an outdoor antenna can be hazardous and should be left to
a professional antenna installer.
Use
14 Cleaning - Unplug this video product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
15 Objects that may touch dangerous voltage points or "short-out" parts could
result in a fire or electric shock. Never spill liquid of any kind on the video
product.
16 Lightning - For added protection for this video product during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the video product due to lightning and power
line surges.
Service
17 Servicing - Do not attempt to service this video product yourself, as opening
or removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
18 Conditions Requiring Service - Unplug this video product from the wall
outlet and refer servicing to qualified service personnel under the following
conditions:
A When the power-supply cord or plug is damaged.
B If liquid has been spilled, or objects have fallen into the video product.
C If the video product has been exposed to rain or water.
D If the video does not operate normally by following the operating
instructions. Adjust only those controls that are covered by operating
instructions. Improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the
video product to its normal operation.
E If the video product has been dropped or cabinet has been damaged.
F When the video product exhibits a distinct change in performance-this
indicates a need for service.
19 Replacement Parts - When replacement parts are required, have the
service technician verify that the replacements he uses have the same
IMPORTANT SAFEGUARDS
Installation
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` B mac001 1200DPI 90LPI

SAFETY INFORMATION
This STB has been manufactured to satisfy international
safety standards.
Please read the following recommended safety precautions
carefully.
Dispose the used batteries at designated place for environment
protection.
MAINS SUPPLY:
OVERLOADING:
LIQUIDS:
CLEANING:
VENTILATION:
ATTACHMENTS:
CONNECTION
TO THE CABLE
TV SIGNAL AND
TV:
SERVICING:
LIGHTNING:
GROUNDING:
AC220-240V~50/60Hz
Do not overload wall outlets, extension
cords or adapters as this can result in fire
or electrical shock.
Keep liquids away from the STB.
Before cleaning, disconnect the STB from
the wall socket. Use a cloth lightly
dampened with water (no solvents) to
clean the exterior.
Do not block the STB ventilation holes.
Ensure that free airflow is maintained
around the STB. Never store the STB
where it is exposed to direct sunlight or
near heating equipment e.g. a radiator.
Never stack other electronic equipment on
top of the STB. Place the STB at least
30mm from the wall.
Do not use any attachment that is not
recommended by the manufacturer; it may
cause a hazard or damage the equipment.
Connect all components before plugging
any power cords into the wall outlet.
Always turn off the STB, TV and other
components before you connect or
disconnect any cables.
Do not attempt to service this product
yourself. Any attempt to do so will make
the warranty invalid. Refer all servicing to
a qualified service agent.
If the STB is installed in an area subject to
intense lightning activity, protection
devices for the STB mains connector and
modem telephone line are essential.
The individual manufacturer's instruction
for safeguarding other equipment, such as
TV set, Hi-Fi, etc., connected to the STB
must also be followed during lightning
storms.
CATV cable MUST BE EARTHED.
The grounding system must comply with
SABS 061.
The meaning of the symbol on the product, its
accessory or packaging indicates that this
product point shall not be treated as household
waste.
Please, dispose of this equipment at your
applicable collection for the recycling of electrical & electronic
equipments waste. In the European Union and Other
European countries, there are separate collection systems for
used electrical and electronic product.
By ensuring the correct disposal of this product, you will help
prevent potential hazards to the environment and to human
health, which could otherwise be caused by unsuitable waste
handling of this product.
The recycling of materials will help conserve natural
resources.
Please do not therefore dispose of your old electrical and
electronic equipment with your household waste.
For more detailed information about recycling of this product,
please contact your local city office, your household waste
disposal service or the shop where you purchased the
product.
safety characteristics as the original parts. Use of replacements specified by
the video product manufacturer can prevent fire, electric shock, or other
hazards.
20 Safety Check - Upon completion of any service or repairs to this video
product, ask the service technician to perform safety checks recommended
by the manufacturer to determine that the video product is in safe operating
condition.
21 Wall or Ceiling Mounting - The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
22 Heat - The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
products heat.
NOTE
WEEE (Waste of electrical and electronic equipment)
This environment-friendly product does not
contain the EU RoHS restricted substances (Pb,
Hg, Cd, Cr6+, PBB, and PBDE).
RoHS (Directive 2002/95/EC) Compliant
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` C mac001 1200DPI 90LPI

CONTENTS
Front panel 1
Rear panel 1
Remote control 1-2
SAFETY INFORMATION
INTRODUCTION-About the STB
General about connections 3
Connecting to the TV aerial 3
Connecting to the TV with SCART 4
Connecting a Amplifier/Receiver system 4
SYSTEM CONNECTION
Easy Install 5
Automatic channel scan 5
Channel scan 5
Tuner Setting 5
GETTING STARTED
Changing Channels 6
Accessing the Electronic Program Guide (EPG)
Accessing the favourite channels
OPERATION
Channel list menu 7
TV Channel List 7
Edit
Find
Sort
Move
Radio Channel List 8
Delete All Favourites 9
Delete All 9
Group Rename 9
CHANNEL
Tools main menu 13
Receiver Information 13
Game 13
Load Factory Default 13
Software Upgrade 14
Tools
15
TROUBLESHOOTING
16
SPECIFICATIONS
System setup menu 10
OSD Language 10
TV System 10
Region and Time 11
Timer Setting 11
OSD Setting 12
Parental Lock 12
SYSTEM SET-UP
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` D mac001 1200DPI 90LPI

1
INTRODUCTION-About the STB
Power indicator
Front panel
Remote sensor
TV Scart
for connection to the TV
Rear panel
Remote control
TV aerial Coaxial Digital Audio AC Mains
RF Loop through
for an external Device
ŒPower On/Standby (Switch the STB ON/STANDBY mode)
´INFO (Press for current channel information)
ˇChannel up/down
¨Recall button (switch to previous channel)
ˆMenu (Open up menu)
ØCursor ( to select sub-menu from the main menu)
∏OK button (Press to enter. In the game mode, press to pause)
”EPG (Open up Electronic Programme Guide menu)
’Numeric entry (Enter numeric values and to select the channel directly by
entering it's number)
˝PAUSE (Pause the current playback picture)
ÔAUDIO (Select audio mode and audio track)
Red Button (For interactive function)
ÒGreen Button (For interactive function)
ÚMUTE (Turn off the volume)
ÆSUBTITLE (On/Off Subtitle)
ıVolume +/- (Turn up/down the volume)
˜EXIT (Exit from menu)
¯FAVOURITE (Open up Favourite list)
˘PAGE + (page up)
¿PAGE - (page down)
¸TV/RADIO (Switch between TV and Radio)
˛TEXT (Open interactive service)
◊Blue Button (For interactive function)
±Yellow Button (For interactive function)
Œ
´
ˇ
¨
ˆ
Ø
∏
”
’
˝
Ô

Ò
Ú
Æ
ı
˜
¯
˘
¿
¸
˛
◊
±
DSD-800M_UK_2007 2007.10.4 2:15 PM ˘ ` 1 mac001 1200DPI 90LPI

INTRODUCTION-About the STB
2
• Remove the battery compartment cover.
• Load two AAA (UM-4 or R03) batteries into the battery
compartment.
• Make sure that the batteries have been inserted with the
correct polarities matching to the symbols +, - marked in
the battery compartment. Close the battery compartment
cover.
• When replacing batteries, replace both batteries. Do not
mix new and used batteries operating together, otherwise,
the operation lifetime will be much shorter than normal.
• Remove the batteries if the unit will not be used for a
prolonged period of time.
The remote control transmits a directional infrared beam. Be
sure to aim the remote control directly at the infrared sensor
of the unit during operation.
If the sensor has been covered or there is a large object
between the remote control and the sensor, the sensor will
not respond.
The sensor may not able to receive the remote signal when it
is exposed to direct sunlight or a strong artificial light
(fluorescent or strobe light). In this case, change the direction
of the light or reposition the unit to avoid direct lighting.
Using Remote control
Within approximately
6 meter (20 feet)
Remote sensor
BE ENVIRONMENTALLY FRIENDLY
Do not dispose batteries as normal rubbish. Be
environmentally friendly, dispose batteries following
the Government's regulation.
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 2 mac001 1200DPI 90LPI

3
SYSTEM CONNECTION
There are many different types of equipments that you can
connect to the STB.
In this manual you will see some of the most common ways to
connect your equipment.
General about connections
You can connect the STB to the following type of aerials:
ŒStandard outdoor aerial
Please note the following:
• In some block of flats, the roof-mounted aerial system
includes a filter and channel selector. If so, the aerial
may not work with the STB. Please consult the landlord.
• Many older roof-mounted aerials may only receive a
limited number of channels. As a result, digital channels
transmitted on higher frequencies are difficult or even
impossible to receive. The problem can be solved by
replacing the roof aerial.
• Some outdoor aerials are directed towards analog relay
transmitters. The aerial must be directed towards digital
main TV transmitter.
• It is not always advisable to position the aerial as high as
possible. If problems arise, experiment with different
aerial heights.
´Indoor and window mounted aerials
• It is not advisable to use indoor or window mounted
aerials, as digital channels will be difficult or even
impossible to receive.
Connecting to the TV aerial
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 3 mac001 1200DPI 90LPI

SYSTEM CONNECTION
4
• Remove the aerial lead from your TV and connect this to
the TV AERIAL input socket on the STB.
• Connect a SCART cable between the main SCART socket
on the TV and the TV SCART socket on the STB.
• Switch on your TV, plug in and switch on your STB.
You may need to select the AV (SCART) input on your TV
to watch Digital TV. In some cases your TV will
automatically select this input when the STB is switched
on.
Connecting to the TV with SCART
Antenna
RF cable
Scart cable
You can connect an RCA/Cinch single cable from the
DIGITAL AUDIO socket on the STB to a HiFi system
equipped with digital audio input. This output is also used for
connection to an external Dolby digital decoder.
Connecting a Amplifier/Receiver system
Amplifier/Receiver
Coaxial cable
• To avoid interference you must use screened audio cables.
• Never connect digital output to any analogue input.
• It is always advisable to consult your HiFi instruction book.
NOTE
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 4 mac001 1200DPI 90LPI

5
GETTING STARTED
If you use the STB for the first time, the "Easy Install" menu
appears.
Press the "LEFT" or "RIGHT" cursor button to setup the
OSD Language.
Press the "OK" button to start channel search.
Easy Install
!Press the "MENU" button to enter main menu.
@Select "Installation", press the "OK" button to enter
Installation menu.
#Select "Channel Scan" and press the "OK" button to
enter the Channel Scan menu.
$Press the "LEFT" or "RIGHT" cursor button to
select Scan mode, Scan Band and Channel No. and
highlight "Search", then press the "OK" button to
start channel scan.
Channel scan
Automatic channel scan
!Press the "MENU" button to enter main menu.
@Select "Installation", press the "OK" button to enter
the Installation menu.
#Select the "Auto Scan", press the "OK" button to
enter the Auto Scan menu.
$Press the "LEFT" or "RIGHT" cursor button to
select Scan mode, and highlight "Search" , then press
the "OK" button to start auto scan.
!Press the "MENU" button to enter main menu.
@Select "Installation", press the “OK” button to enter
Installation menu,
Press the "UP" or "DOWN" cursor button to select
the "Tuner Power",
Press the "OK" button and "Tuner Power" option is
highlighted.
#Press the "LEFT" or "RIGHT" cursor button to
select the desired setting.
When selected "On", the STB will provide tuner power.
It will not provide this power if "Off" is selected.
$Press the "EXIT" button to exit.
Tuner Setting
➠
➠
➠➠
➠
➠➠
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 5 mac001 1200DPI 90LPI

6
OPERATION
Changing Channels
There are four ways of channel selection - stepping through
the channel list, selection by number, from the on-screen
channel list, and using the electronic programme guide
(EPG).
!Stepping through the channel list:
To move through the channel list, press the upward
arrow or downward arrow key on the remote control.
@Selected by number:
Enter the channel number directly by pressing numeric
buttons, and press the "OK" button to select desired
channel.
#Selected by on-screen channels list:
You can also select the required channel directly from
on-screen channel list. This is displayed using the STB's
main menu. See "Channel List" in this manual for
operation detail.
$Selected by EPG:
You can also select the required channel directly from
electronic program guide (EPG).
This is displayed using the STB's main menu. See
"Accessing the Electronic Program Guide (EPG)" in this
manual for operation detail.
Accessing the Electronic Program Guide (EPG)
Accessing the EPG of all channels:
!Press the "EPG" button to enter EPG menu .
@Press numeric button "2" to move cursor to the
schedule window.
#Press numeric button "3" to check the detail
information of the selected program, then press numeric
button "1" to check the extended information.
Accessing the favourite channels
!Press the "FAV" button to enter favourite group
menu.
@Press the "UP" or "DOWN" cursor button to select
the desired favourite group.
#Press the "OK" button to enter the favourite
channels list, and press the "UP" or "DOWN" cursor
button to select your favourite channel.
Booking:
In a schedule window, press the "OK" button to book
program that you want to see, the selected program will be
added to the "Booking List" and marked with a symbol .
➠
➠➠
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 6 mac001 1200DPI 90LPI

7
CHANNEL
!Press the "MENU" button to enter the main menu,
select "Channel" and press the "OK" button to enter
Channel menu.
@Press the "UP" or "DOWN" cursor button to
highlight the desired item and press the "OK" button
to enter the setting menu.
#Press the "EXIT" button to exit.
Channel list menu
!In the Channel menu, select "TV Channel List", press the
"OK" button to enter TV channel list menu.
@Press the "LEFT" or "RIGHT" cursor button to
select channel group.
And press the "UP" or "DOWN" cursor button to
preview the desired TV channel. Press the "OK" button
to view the selected channel in full screen.
TV Channel List
You can also press the "OK" button to enter channel list in normal
playback mode.
NOTE
Edit
Use this menu to favour, lock, skip, delete and rename
channel list.
• In channel list menu, press numeric button "1" to enter
edit menu.
• Highlight a channel and press the "OK" button to
select it . Or press numeric button "0" to 0007 Sky
News to select all channels. And
the selected channels will be
marked in a symbol " ".
• Press the "MENU" button to
quit the edit menu.
Favour:
• In "Edit Channel" menu, press numeric button "1" ,
then press the "UP" or "DOWN" cursor button
to select a desired group, and press the "OK" button ,
a confirmation window appears.
• Select "Yes" and press the "OK" button , the selected
channel will be added to the group and marked with a
symbol " ".
Lock:
• In "Edit Channel" menu, press numeric button "2" , a
confirmation window appears. Select "Yes", press the "OK"
button , the selected channel will be locked and
marked with a symbol " " . Repeat steps above to
unlock the locked channels.
Skip:
• In "Edit Channel" menu, press numeric button "3" , a
confirmation window appears. Select "Yes", press the"OK"
button , the selected channel will be marked with a
symbol " " and skipped while you change the channel
in full screen. Repeat steps above to cancel the skipped
channels.
Delete:
• In "Edit Channel" menu, press numeric button "4" , a
confirmation window appears. Select "Yes", press the "OK"
button to delete the selected channels from channel
list.
Rename:
• In "Edit Channel" menu, press numeric button "5" to
open the mock keypad. Input letter and numeric one by
one by pressing the cursor button and press the "OK"
button to confirm. After complete input, highlight "OK"
on mock keypad to confirm, you changed the channel
name successfully.
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 7 mac001 1200DPI 90LPI

8
CHANNEL
!In channel list menu, press numeric button "2" to
enter Find menu.
@Press cursor button to highlight desired letters or
numbers and press the "OK" button to input one by
one. After input each character, the channel list will
search the channel according to your input and list the
matched channel.
#Press the "EXIT" button to quit "Find" menu.
• Press the "EXIT" button or Highlight "ESC" and press
the "OK" button to close the mock keypad, and save
any modification.
Find
!In channel list menu, press numeric button "3" to
enter "Sort" menu.
@Press the "UP" or "DOWN" cursor button to highlight
desired sort way and press the "OK" button to
confirm.
Default : Sorting by scanning result.
Name (A-Z) : Sorting in Alphabetical Order.
Name (Z-A) : Sorting in Alphabetical Order.
FTA : Sieving out all free fare channels.
Lock : Accumulating all locked channels and list in the
last of TV Channel List.
Sort
!In channel list menu, press numeric button "4" , the
selected channel will be marked by a symbol " ".
Then press the "UP" or "DOWN" cursor button to
move the selected channel to the position that you want
to place.
@Press the "OK" button , a confirmation window
appears.
Select "Yes", press the "OK" button to change the
channel order.
Move
!In the Channel menu, select "Radio Channel List", press
the "OK" button to enter the radio channel list menu.
@Press the "LEFT" or "RIGHT" cursor button to
select channel group.
Press the "UP" or "DOWN" cursor button to highlight
desired channel,
and press the "OK" button to listen the channel.
Radio Channel List
Basically, the operation of "Radio Channel List" is same as "TV
Channel List", but there is one point different: In "Radio Channel List"
mode, there is no video information, so it will always display Radio's
logo in the right side preview window.
NOTE
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 8 mac001 1200DPI 90LPI

9
CHANNEL
Use this menu to delete all channels.
!In the Channel menu, select "Delete All", press the "OK"
button , you will be asked to input the password
(The default password is 0000).
@Input the correct password, a warning window appears.
Select "Yes", press the "OK" button to delete all
channels.
Select "No", press the "OK" button to cancel
deletions.
Delete All
Use this menu to change the group name.
!In Channel menu, select "Group Rename", press the
"OK" button to enter the group rename menu.
@Select desired group, press the "OK" button to open
the mock keypad.
Input letter and numeric one by one by pressing the
cursor button and press the "OK" button to
confirm.
After finishing input, highlight "OK" on mock keypad to
confirm, you changed the group name successfully.
#Press the "EXIT" button to quit the group rename
menu.
Group Rename
Use this menu to delete all favourite channels.
!In the Channel menu, select "Delete All Favourites",
press the "OK" button , a warning window appears.
@Select "Yes" and press the "OK" button to delete all
favourite channels.
Select "No" and press the "OK" button to cancel
deleting.
Delete All Favourites
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 9 mac001 1200DPI 90LPI

10
SYSTEM SET-UP
System setup menu allows us to set OSD Language, TV
System, Region and Time, Timer Setting, OSD Setting and
Parental Lock.
!Press the "MENU" button to enter the main menu,
select "Setup" and press the "OK" button to enter
system setup menu.
@Press the "UP" or "DOWN" cursor button to highlight
the desired menu and press the "OK" button to
enter the setting menus.
Then press the "UP" or "DOWN" cursor button to
select the desired item, press the "LEFT" or "RIGHT"
cursor button to change the setting.
#Press the "EXIT" button to exit.
System setup menu
This menu allows you to set the OSD Language.
OSD Language : To select your desired OSD language.
OSD Language
This menu allows us to set the Aspect Ratio, Video Output
and LCN Mode.
Aspect Ratio : Aspect Mode is used for switching the
screen aspect ratio mode.
4:3 PS 4:3 Pan Scan
4:3 LB 4:3 Letter Box
16:9 16:9 Wide Screen
Video Output : Video Output is use for switching the
video output mode.
RGB Set to RGB (Red, Green, Blue)
CVBS Set video output signal to CVBS
(Composite Video Blanking Sync)
LCN Mode : If LCN (Logical Channel Number) Select
function is activated, You can't change the original
number of TV channels by scanning.
You can activate/deactivate the LCN function by setting
the "LCN Mode" to on/off.
TV System
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 10 mac001 1200DPI 90LPI

11
SYSTEM SET-UP
This menu allows you to set the
program timer and sleep timer.
Program Timer : This menu is used for setting the
program timer.
Timer Number You can set 8 program times.
Timer Mode Off/Once/Daily/Weekly/Monthly
Timer Service TV Service/Radio Service
Wakeup Channel You can select a desired channel as
the wakeup channel.
Month/Date/Day Press the "LEFT" or "RIGHT" cursor
button to select your desired month,
date and day.
Timer Service Press the "OK" button then
numeric buttons to input the time.
When you want to quit program
timer, a saving window appears.
Sleep Timer : You can set the
STB (Set Top Box) to power off
automatically in 10 min, 30 min,
60 min, 90 min and 120 min.
Timer Setting
This menu allows you to set the region and time.
Region : This menu is used for changing the region
setting.
GMT Usage : This menu is used for open the usage of
GMT.
The options are : Off / User Define / By Region
GMT Offset : This menu is valid only when "User
Define" has been selected in the GMT Usage menu.
The GMT offset range is "-11:30 ~ +12:00", increasing
half hour progressively.
Date & Time: "Date" and "Time" menus are valid only
when "Off" is selected in the GMT Usage menu.
Press the "OK" button then numeric buttons to
change the date and time.
Time Display : This menu allow you to control whether
the time is displayed on screen or not.
The options are : Off/On.
Region and Time
DSD-800M_UK_2007 2007.10.2 5:58 PM ˘ ` 11 mac001 1200DPI 90LPI

12
SYSTEM SET-UP
This menu allows you to set Subtitle Display, OSD
Transparency, OSD Style and load default OSD setting.
Subtitle Display : To set the subtitle to Standard or Off.
OSD Transparency : To set the OSD transparency to
Off/10%/20%/30%/40%/50%.
OSD Style : To set the OSD style to Style1/Style 2
Load Default OSD Setting : To clear all OSD setting
and reset parameters as default value.
OSD Setting
This menu allows you to password protect the installation
menu and channel, and change the password.
!In "System Setup" menu, select "Parental Lock" and
press the "OK" button , you are asked to input a
password (the default password is "0000").
@After inputting the correct password by pressing numeric
buttons, the parental lock menu appears.
Menu Lock : To lock the installation menu. When you
want to enter any installation sub-menu, you must input
the password. You can set menu lock to on/off.
New Password : To change the password.
Confirm Password : To confirm the new password.
Parental Lock
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 12 mac001 1200DPI 90LPI

13
Tools
!Press the "MENU" button to enter main menu.
Select "Tools", press the "OK" button to enter tools
menu.
@Press the "UP" or "DOWN" cursor button to highlight
desired menu and press the "OK" button to enter.
#Press "EXIT" button to exit.
Tools main menu
This menu can display some parameters of Receiver,
Hardware, Software, Signature and Remote Control
information in this STB.
!In "Tools" menu, select "Receiver Information", press the
"OK" button to open receiver information window.
@Press the "EXIT" button to exit.
Receiver Information
This menu allows you to play games on this STB.
!In "Tools" menu, select "Game", press the "OK" button
to enter the game menu.
@Press the "UP" or "DOWN" cursor button to select a
desired game, and press the "OK" button to enter
the game.
Highlight "Start" and press the "OK" button to start
the game.
#Press the "EXIT" button to quit the game.
Game
This menu allows you to re-set the STB back to factory
settings, clear all existing channels.
!Enter "Tools" menu, select "Load Factory Default", press
the "OK" button , you are asked to input password.
@Input a correct password using the numeric buttons (the
default password is "0000"), a confirmation window is
displayed.
#Select "Yes" to return back to factory settings and clear
all channels.
Select "No" to cancel back to factory settings.
$Press the "EXIT" button to exit.
Load Factory Default
You can also press the "OK" button to pause playing.
NOTE
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 13 mac001 1200DPI 90LPI

14
We offer the functions for user to upgrade software version by
RS-232 Interface via Scart jack or by air.
!Enter "Tools" menu, select "Software Upgrade", press
the "OK" button , Software Upgrade menu is shown.
@Press "Up" or "Down" button to select the desired item
and press the "OK" button , you are asked to input
password.
#Input the correct password (the default password is
0000.), Software Upgrade sub-menu is opened.
$Press "EXIT" button to exit.
Upgrade by RS-232
Connect master STB to slave receiver via serial
interface.
Enter Upgrade by RS-232 sub-menu in Master STB,
then press "LEFT" or "RIGHT" button to change
the Transfer Mode and Upgrade mode.
Turn on slave STB and it needn't operate any setting.
Highlight "Start" on master STB and press the "OK"
button to start upgrade.
Upgrade by Air
Enter Upgrade by Air sub-menu, then press the "OK"
button to set Frequency, Bandwidth, Download PID
according to information from service agent and press
the "OK" button .
Highlight "Start" on master STB and press the "OK"
button to start upgrade.
Software Upgrade
Tools
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 14 mac001 1200DPI 90LPI

15
TROUBLESHOOTING
In some region, the digital terrestrial signal may be weak. So it is advisable to use an antenna with a signal booster for watching
weak signal channels.
Problem Possible cause What to do
Standby light not lit.
No signal found.
No picture or sound.
Scrambled channel message.
No response to remote control.
Forgotten channel lock code.
Forgotten menu lock code.
The remote control will not operate
your STB.
After moving the STB to another
room you find you are no longer able
to receive digital reception.
Mains lead unplugged.
Mains fuse blown.
Aerial is disconnected.
Aerial is damaged/ misaligned.
Out of digital signal area.
Scart/AV is not selected on your TV.
Channel is scrambled.
Receiver off.
Handset not aimed correctly.
Front panel obstructed.
Hand set batteries exhausted
(1)The batteries in your remote control need
replacing.
(2)There is an obstruction blocking the signal
path between the remote control and the
box.
The aerial feed for the new aerial point may
come through a distribution system which may
reduce the digital signal now received by the
box.
Check mains lead.
Check fuse.
Check aerial lead.
Check aerial.
Check with dealer.
Move to another input.
Select alternative channel.
Plug in and turn on power.
Aim handset at front panel.
Check for obstructions.
Replace handset batteries.
Re-install channels to cancel channel
lock.
Contact help line.
(1)Replace the batteries.
(2)Check that there is nothing in the
way of the path between the
remote control and the receiver.
Try a direct feed from the antenna.
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 15 mac001 1200DPI 90LPI

16
SPECIFICATIONS
RF INPUT CONNECTOR x1 (IEC-TYPE,
IEC169-2, FEMALE)
RF OUTPUT CONNECTOR x1
(IEC-TYPE, IEC169-2, MALE
(LOOPTHROUGH))
FREQUENCY RANGE 470MHz ~ 862MHz (UHF)
SIGNAL LEVEL -15 ~ -70 dbm
TUNER & CHANNEL
TRANSPORT STREAM MPEG-2 ISO/IEC 13818
PROFILE LEVEL MPEG-2 MAIN PROFILE
@MAIN LEVEL
INPUT RATE MAX. 15Mbit/s
VIDEO FORMATS 4:3/16:9 SWITCHABLE
AUDIO FORMAT MPEG Layer I & II, 32 / 44.1 /
48KHz
VIDEO OUTPUT CVBS, RGB (DEFAULT)
DECODER
MAIN POWER CABLE FIXED TYPE
TUNER ANTENNA INPUT x 1, RF
OUTPUT x1
SCART TV INPUT x 1
SPDIF COAXIAL x 1
CONNECTION
INPUT VOLTAGE AC220~240V, 50/60Hz
POWER CONSUMPTION MAX. / OPERATION : 7W
STANDBY : 3W
POWER SUPPLY
Design and Specifications are subject to change without notice.
NOTE
DSD-800M_UK_2007 2007.10.2 5:54 PM ˘ ` 16 mac001 1200DPI 90LPI