Daikin VRV X RXQ6-48ANR Series User manual

Service
Manual
Cooling Only 50/60 Hz
RXQ6-48A(N)R Series
SiME341909EA

SiME341909EA
iTable of Contents
Introduction .................................................................................... 1
1. Safety Cautions.......................................................................................2
1.1 Warnings and Cautions Regarding Safety of Workers.............................2
1.2 Warnings and Cautions Regarding Safety of Users.................................4
2. Icons Used ..............................................................................................6
3. Revision History ......................................................................................7
Part 1 General Information ............................................................ 8
1. Model Names ..........................................................................................9
1.1 Indoor Unit................................................................................................9
1.2 Outdoor Unit .............................................................................................9
2. External Appearance.............................................................................10
2.1 Indoor Unit..............................................................................................10
2.2 Outdoor Unit ...........................................................................................11
3. Combination of Outdoor Units...............................................................12
4. Capacity Range.....................................................................................13
4.1 Connection Ratio....................................................................................13
4.2 Outdoor Unit Combinations ....................................................................14
5. Specifications ........................................................................................15
Part 2 Refrigerant Circuit............................................................. 18
1. Refrigerant Circuit (Piping Diagrams) ...................................................19
1.1 Outdoor Unit ...........................................................................................19
1.2 Indoor Unit..............................................................................................23
2. Functional Parts Layout ........................................................................25
2.1 RXQ6/8AR..............................................................................................25
2.2 RXQ10/12/14/16AR................................................................................26
3. Refrigerant Flow for Each Operation Mode...........................................27
3.1 RXQ6/8/10/12AR....................................................................................27
3.2 RXQ14/16AR..........................................................................................29
Part 3 Remote Controller ............................................................. 31
1. Applicable Models .................................................................................32
2. Names and Functions ...........................................................................34
2.1 BRC1E63 ...............................................................................................34
2.2 BRC1H81 Series ....................................................................................36
2.3 BRC4M Series........................................................................................38
3. Main/Sub Setting...................................................................................41
3.1 Wired Remote Controller (BRC1E63) ....................................................41
3.2 Wired Remote Controller (BRC1H81 Series) .........................................42
3.3 When Wireless Remote Controller is Used Together.............................43
4. Address Setting for Wireless Remote Controller...................................44
4.1 Setting for Signal Receiver PCB ............................................................44
4.2 Setting for BRC4M Series ......................................................................45
4.3 Multiple Settings A/b...............................................................................46
5. Centralized Control Group No. Setting..................................................47
5.1 BRC1E63 ...............................................................................................47
5.2 BRC1H81 Series ....................................................................................49

SiME341909EA
Table of Contents ii
5.3 Group No. Setting Example....................................................................50
6. Service Settings Menu, Maintenance Menu..........................................51
6.1 BRC1E63 ...............................................................................................51
6.2 BRC1H81 Series ....................................................................................55
Part 4 Functions and Control ....................................................... 56
1. Function Flowchart................................................................................57
2. Stop Control ..........................................................................................58
2.1 Abnormal Shutdown ...............................................................................58
2.2 Slave Unit Stops during Master Unit Operation......................................58
3. Standby Control ....................................................................................59
3.1 Restart Standby......................................................................................59
4. Startup Control ......................................................................................60
4.1 Cooling Startup Control ..........................................................................60
5. Normal Control ......................................................................................61
5.1 List of Functions in Normal Control ........................................................61
5.2 Compressor Control ...............................................................................61
5.3 Compressor Capacity Control ................................................................62
5.4 Operating Priority and Rotation of Compressors....................................63
5.5 Compressor Step Control.......................................................................64
5.6 Step Control of Outdoor Fans ................................................................64
6. Protection Control .................................................................................65
6.1 High Pressure Protection Control...........................................................65
6.2 Low Pressure Protection Control............................................................65
6.3 Discharge Pipe Protection Control .........................................................66
6.4 Compressor Body Protection Control.....................................................66
6.5 Inverter Protection Control .....................................................................67
7. Special Control......................................................................................68
7.1 Outdoor Unit Rotation.............................................................................68
7.2 Oil Return Control...................................................................................69
7.3 Inverter Pre-Heat Control .......................................................................70
8. Outline of Control (Indoor Unit) .............................................................71
8.1 Set Temperature and Control Target Temperature................................71
8.2 Thermostat Control.................................................................................71
8.3 Automatic Airflow Rate Control ..............................................................73
8.4 Airflow Direction Control.........................................................................74
8.5 Auto Draft Reducing Control (FXFSQ-AR only) .....................................75
8.6 Eco Full Automatic Control (FXFSQ-AR only)........................................75
8.7 Drain Pump Control................................................................................76
8.8 Freeze-Up Prevention Control................................................................78
8.9 Dew Condensation Prevention Control ..................................................79
8.10 Electronic Expansion Valve Control .......................................................80
8.11 Circulation Airflow (FXFSQ-AR only) .....................................................81
Part 5 Field Settings and Test Operation .................................... 83
1. Field Settings for Indoor Unit.................................................................84
1.1 Field Settings with Remote Controller ....................................................84
1.2 List of Field Settings for Indoor Unit .......................................................88
1.3 Applicable Field Settings ........................................................................90
1.4 Details of Field Settings for Indoor Unit..................................................91

SiME341909EA
iii Table of Contents
1.5 Operation Control Mode .......................................................................102
2. Field Settings for Outdoor Unit............................................................104
2.1 Function Setting ...................................................................................104
2.2 Settings by DIP Switches .....................................................................105
2.3 Settings by BS Buttons.........................................................................108
2.4 Normal Mode........................................................................................110
2.5 Monitor Mode (Mode 1) ........................................................................111
2.6 Setting Mode (Mode 2).........................................................................115
2.7 Eco Mode Setting .................................................................................126
2.8 Night-Time Low Noise Operation and Demand Operation...................127
3. Test Operation ....................................................................................131
3.1 Checks before Test Operation .............................................................131
3.2 Checkpoints..........................................................................................131
3.3 Test Operation Procedure....................................................................132
3.4 Turn Power ON ....................................................................................133
Part 6 Service Diagnosis ............................................................ 134
1. Servicing Items to be Confirmed .........................................................136
1.1 Troubleshooting....................................................................................136
1.2 Precautions for Maintenance................................................................136
2. Symptom-based Troubleshooting .......................................................138
2.1 With Optional Infrared Presence/Floor Sensor.....................................140
2.2 For All Outdoor Units............................................................................141
3. Refrigerant Properties (R-410A) .........................................................142
4. Troubleshooting with Remote Controller.............................................143
4.1 BRC1E63 .............................................................................................143
4.2 BRC1H81 Series ..................................................................................144
4.3 BRC4M Series......................................................................................145
5. Troubleshooting by Error Code ...........................................................146
5.1 Error Codes and Descriptions ..............................................................146
5.2 Error Codes (Sub Codes).....................................................................148
5.3 External Protection Device Abnormality ...............................................158
5.4 Indoor Unit PCB Abnormality ...............................................................159
5.5 Drain Level Control System Abnormality..............................................160
5.6 Indoor Fan Motor Lock, Overload.........................................................162
5.7 Indoor Fan Motor Abnormality..............................................................164
5.8 Power Supply Voltage Abnormality ......................................................170
5.9 Electronic Expansion Valve Coil Abnormality, Dust Clogging ..............173
5.10 Humidifier System Abnormality ............................................................174
5.11 Auto Grille Unit Error ............................................................................175
5.12 Defective Capacity Setting ...................................................................176
5.13 Transmission Error (between Indoor Unit PCB and Fan PCB) ............177
5.14 Transmission Error ...............................................................................179
5.15 Transmission Error (between Indoor Unit PCB and Auto Grille
Control PCB) ........................................................................................180
5.16 Thermistor Abnormality ........................................................................182
5.17 Combination Abnormality (between Indoor Unit PCB and Fan PCB)...183
5.18 Capacity Setting Abnormality ...............................................................184
5.19 Indoor Unit PCB Abnormality ...............................................................185
5.20 Infrared Presence/Floor Sensor Error ..................................................186
5.21 Remote Controller Thermistor Abnormality ..........................................191

SiME341909EA
Table of Contents iv
5.22 Outdoor Unit Main PCB Abnormality....................................................192
5.23 Current Leakage Detection ..................................................................193
5.24 Missing of Leakage Detection Core .....................................................194
5.25 Activation of High Pressure Switch ......................................................195
5.26 Activation of Low Pressure Sensor ......................................................197
5.27 Compressor Motor Lock .......................................................................198
5.28 Outdoor Fan Motor Abnormality...........................................................200
5.29 Electronic Expansion Valve Coil Abnormality.......................................203
5.30 Discharge Pipe Temperature Abnormality ...........................................204
5.31 Wet Alarm.............................................................................................206
5.32 Refrigerant Overcharged......................................................................208
5.33 Harness Abnormality
(between Outdoor Unit Main PCB and Inverter PCB) ..........................209
5.34 Outdoor Fan PCB Abnormality.............................................................210
5.35 Thermistor Abnormality ........................................................................211
5.36 High Pressure Sensor Abnormality ......................................................213
5.37 Low Pressure Sensor Abnormality .......................................................214
5.38 Inverter PCB Abnormality.....................................................................215
5.39 Momentary Power Failure during Test Operation ................................217
5.40 Inverter Radiation Fin Temperature Rise Abnormality .........................218
5.41 Compressor Instantaneous Overcurrent ..............................................220
5.42 Compressor Overcurrent......................................................................222
5.43 Compressor Startup Abnormality .........................................................224
5.44 Transmission Error
between Inverter PCB and Outdoor Unit Main PCB.............................227
5.45 Power Supply Voltage Imbalance ........................................................229
5.46 Reactor Temperature Abnormality .......................................................231
5.47 Inverter Radiation Fin Temperature Abnormality .................................232
5.48 Field Setting after Replacing Outdoor Unit Main PCB Abnormality or
Combination of PCB Abnormality.........................................................234
5.49 Refrigerant Shortage Warning..............................................................235
5.50 Open Phase .........................................................................................236
5.51 Power Supply Insufficient or Instantaneous Abnormality .....................237
5.52 Check Operation Not Executed............................................................239
5.53 Transmission Error between Indoor Units and Outdoor Units..............240
5.54 Transmission Error between Remote Controller and Indoor Unit.........243
5.55 Transmission Error between Outdoor Units .........................................244
5.56 Transmission Error between Main and Sub Remote Controllers .........249
5.57 Other Indoor Units and Outdoor Unit Abnormality................................250
5.58 Improper Combination of Indoor Unit and Outdoor Unit, Indoor Unit
and Remote Controller .........................................................................251
5.59 Address Duplication of Centralized Controller......................................254
5.60 Transmission Error between Centralized Controller and Indoor Unit ...255
5.61 System Not Set Yet ..............................................................................258
5.62 System Abnormality, Refrigerant System Address Undefined .............259
6. Check ..................................................................................................261
6.1 High Pressure Check ...........................................................................261
6.2 Low Pressure Check ............................................................................262
6.3 Superheat Operation Check.................................................................263
6.4 Power Transistor Check .......................................................................264
6.5 Refrigerant Overcharge Check.............................................................266
6.6 Refrigerant Shortage Check.................................................................267

SiME341909EA
vTable of Contents
6.7 Vacuuming and Dehydration Procedure ..............................................268
6.8 Thermistor Check .................................................................................269
6.9 Pressure Sensor Check .......................................................................272
6.10 Broken Wire Check of the Relay Wires ................................................273
6.11 Fan Motor Connector Check (Power Supply Cable) ............................275
6.12 Fan Motor Connector Check (Signal Cable) ........................................277
6.13 Electronic Expansion Valve Coil Check ...............................................278
Part 7 Appendix .......................................................................... 281
1. Wiring Diagrams..................................................................................282
1.1 Outdoor Unit .........................................................................................282
1.2 Indoor Unit............................................................................................285

SiME341909EA
Introduction 1
1. Safety Cautions.......................................................................................2
1.1 Warnings and Cautions Regarding Safety of Workers.............................2
1.2 Warnings and Cautions Regarding Safety of Users.................................4
2. Icons Used ..............................................................................................6
3. Revision History ......................................................................................7
Introduction

Safety Cautions SiME341909EA
2Introduction
1. Safety Cautions
Be sure to read the following safety cautions before conducting repair work.
After the repair work is complete, be sure to conduct a test operation to ensure that the
equipment operates normally, and explain the cautions for operating the product to the
customer.
Caution Items The caution items are classified into Warning and Caution. The Warning items are
especially important since death or serious injury can result if they are not followed closely. The
Caution items can also lead to serious accidents under some conditions if they are not
followed. Therefore, be sure to observe all the safety caution items described below.
Pictograms This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown in the illustration or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown in the illustration or near the symbol.
1.1 Warnings and Cautions Regarding Safety of Workers
This manual is for the
person in charge of
maintenance and
inspection.
Warning
Do not store equipment in a room with fire sources (e.g., naked
flames, gas appliances, electric heaters).
Be sure to disconnect the power cable from the socket before
disassembling equipment for repair.
Working on equipment that is connected to the power supply may cause
an electrical shock.
If it is necessary to supply power to the equipment to conduct the repair or
inspect the circuits, do not touch any electrically charged sections of the
equipment.
If refrigerant gas is discharged during repair work, do not touch the
discharged refrigerant gas.
Refrigerant gas may cause frostbite.
When disconnecting the suction or discharge pipe of the
compressor at the welded section, evacuate the refrigerant gas
completely at a well-ventilated place first.
If there is gas remaining inside the compressor, the refrigerant gas or
refrigerating machine oil discharges when the pipe is disconnected, and it
may cause injury.
If refrigerant gas leaks during repair work, ventilate the area.
Refrigerant gas may generate toxic gases when it contacts flames.
Be sure to discharge the capacitor completely before conducting
repair work.
The step-up capacitor supplies high-voltage electricity to the electrical
components of the outdoor unit.
A charged capacitor may cause an electrical shock.

SiME341909EA Safety Cautions
Introduction 3
Do not turn the air conditioner on or off by plugging in or
unplugging the power cable.
Plugging in or unplugging the power cable to operate the equipment may
cause an electrical shock or fire.
Be sure to wear a safety helmet, gloves, and a safety belt when
working in a high place (more than 2 m).
Insufficient safety measures may cause a fall.
In case of R-32 / R-410A refrigerant models, be sure to use pipes,
flare nuts and tools intended for the exclusive use with the R-32 /
R-410A refrigerant.
The use of materials for R-22 refrigerant models may cause a serious
accident, such as a damage of refrigerant cycle or equipment failure.
Do not mix air or gas other than the specified refrigerant (R-32 /
R-410A / R-22) in the refrigerant system.
If air enters the refrigerant system, an excessively high pressure results,
causing equipment damage and injury.
Caution
Do not repair electrical components with wet hands.
Working on the equipment with wet hands may cause an electrical shock.
Do not clean the air conditioner with water.
Washing the unit with water may cause an electrical shock.
Be sure to provide an earth / grounding when repairing the
equipment in a humid or wet place, to avoid electrical shocks.
Be sure to turn off the power switch and unplug the power cable
when cleaning the equipment.
The internal fan rotates at a high speed, and may cause injury.
Be sure to conduct repair work with appropriate tools.
The use of inappropriate tools may cause injury.
Be sure to check that the refrigerating cycle section has cooled
down enough before conducting repair work.
Working on the unit when the refrigerating cycle section is hot may cause
burns.
Conduct welding work in a well-ventilated place.
Using the welder in an enclosed room may cause oxygen deficiency.
Warning

Safety Cautions SiME341909EA
4Introduction
1.2 Warnings and Cautions Regarding Safety of Users
Warning
Do not store the equipment in a room with fire sources (e.g., naked
flames, gas appliances, electric heaters).
Be sure to use parts listed in the service parts list of the applicable
model and appropriate tools to conduct repair work. Never attempt
to modify the equipment.
The use of inappropriate parts or tools may cause an electrical shock,
excessive heat generation or fire.
If the power cable and lead wires are scratched or have deteriorated,
be sure to replace them.
Damaged cable and wires may cause an electrical shock, excessive heat
generation or fire.
Do not use a joined power cable or extension cable, or share the
same power outlet with other electrical appliances, since it may
cause an electrical shock, excessive heat generation or fire.
Be sure to use an exclusive power circuit for the equipment, and
follow the local technical standards related to the electrical
equipment, the internal wiring regulations, and the instruction
manual for installation when conducting electrical work.
Insufficient power circuit capacity and improper electrical work may cause
an electrical shock or fire.
Be sure to use the specified cable for wiring between the indoor and
outdoor units.
Make the connections securely and route the cable properly so that there
is no force pulling the cable at the connection terminals.
Improper connections may cause excessive heat generation or fire.
When wiring between the indoor and outdoor units, make sure that
the terminal cover does not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section may
cause an electrical shock, excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cables may cause an electrical shock or fire.
Placing heavy items on the power cable, or heating or pulling the power
cable may damage it.
Do not mix air or gas other than the specified refrigerant (R-32 /
R-410A / R-22) in the refrigerant system.
If air enters the refrigerant system, an excessively high pressure results,
causing equipment damage and injury.
If the refrigerant gas leaks, be sure to locate the leaking point and
repair it before charging the refrigerant. After charging the
refrigerant, make sure that there is no leak.
If the leaking point cannot be located and the repair work must be
stopped, be sure to pump-down, and close the service valve, to prevent
refrigerant gas from leaking into the room. Refrigerant gas itself is
harmless, but it may generate toxic gases when it contacts flames, such
as those from fan type and other heaters, stoves and ranges.
When relocating the equipment, make sure that the new installation
site has sufficient strength to withstand the weight of the
equipment.
If the installation site does not have sufficient strength or the installation
work is not conducted securely, the equipment may fall and cause injury.

SiME341909EA Safety Cautions
Introduction 5
Check to make sure that the power cable plug is not dirty or loose,
then insert the plug into a power outlet securely.
If the plug is dusty or has a loose connection, it may cause an electrical
shock or fire.
When replacing the coin battery in the remote controller, be sure to
dispose of the old battery to prevent children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Caution
Installation of a leakage breaker is necessary in some cases
depending on the conditions of the installation site, to prevent
electrical shocks.
Do not install the equipment in a place where there is a possibility of
combustible gas leaks.
If combustible gas leaks and remains around the unit, it may cause a fire.
Check to see if parts and wires are mounted and connected
properly, and if connections at the soldered or crimped terminals
are secure.
Improper installation and connections may cause excessive heat
generation, fire or an electrical shock.
If the installation platform or frame has corroded, replace it.
A corroded installation platform or frame may cause the unit to fall,
resulting in injury.
Check the earth / grounding, and repair it if the equipment is not
properly earthed / grounded.
Improper earth / grounding may cause an electrical shock.
Be sure to measure insulation resistance after the repair, and make
sure that the resistance is 1 MΩ or higher.
Faulty insulation may cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage may cause water to enter the room and wet the furniture
and floor.
Do not tilt the unit when removing it.
The water inside the unit may spill and wet the furniture and floor.
Warning

Icons Used SiME341909EA
6Introduction
2. Icons Used
The following icons are used to attract the attention of the reader to specific information.
Icon Type of
Information
Description
Warning
Warning Warning is used when there is danger of personal injury.
Caution
Caution Caution is used when there is danger that the reader,
through incorrect manipulation, may damage equipment,
lose data, get an unexpected result or have to restart (part
of) a procedure.
Note
Note Note provides information that is not indispensable, but
may nevertheless be valuable to the reader, such as tips
and tricks.
Reference
Reference Reference guides the reader to other places in this binder
or in this manual, where he/she will find additional
information on a specific topic.

SiME341909EA Revision History
Introduction 7
3. Revision History
Month / Year Version Revised contents
10 / 2019 SiME341909E First edition
05 / 2020 SiME341909EA Model addition: FXAQ20/25/32/40/50/63ARVM

SiME341909EA
8Part 1 General Information
1. Model Names ..........................................................................................9
1.1 Indoor Unit................................................................................................9
1.2 Outdoor Unit .............................................................................................9
2. External Appearance.............................................................................10
2.1 Indoor Unit..............................................................................................10
2.2 Outdoor Unit ...........................................................................................11
3. Combination of Outdoor Units...............................................................12
4. Capacity Range.....................................................................................13
4.1 Connection Ratio....................................................................................13
4.2 Outdoor Unit Combinations ....................................................................14
5. Specifications ........................................................................................15
Part 1
General Information

SiME341909EA Model Names
Part 1 General Information 9
1. Model Names
1.1 Indoor Unit
Power supply and standard symbols
V1, VM: 1 phase, 220-240 V, 50/60 Hz
1.2 Outdoor Unit
YFK: 3 phase, 380-415 V, 50/60 Hz (for Middle East)
Capacity range kW 2.2 2.8 3.6 4.5 5.6 7.1 9.0 11.2 14.0 16.0 Power
supply,
Standard
HP 0.8 11.25 1.6 22.5 3.2 4 5 6
Capacity index 20 25 31.25 40 50 62.5 80 100 125 140
Ceiling mounted cassette
(Round flow with sensing) type FXFSQ ― 25AR 32AR 40AR 50AR 63AR 80AR 100AR 125AR 140AR V1
Slim ceiling
mounted duct
type
(Standard
series)
with
drain
pump FXDQ
20PD25PD32PD―――――――
VM
― ― ― 40ND 50ND 63ND ― ― ― ―
Ceiling mounted duct type FXMQ ― ― ― 40PB 50PB 63PB 80PB 100PB 125PB 140PB V1
― ― ― 40AR 50AR 63AR 80AR 100AR ― ―
Wall mounted type FXAQ 20AR 25AR 32AR 40AR 50AR 63AR ― ― ― ― VM
Series Model name Power
supply
Outdoor units
RXQ
6AR 8AR 10AR 12AR 14AR 16AR 18ANR 20ANR
YFK22ANR 24ANR 26ANR 28ANR 30ANR 32ANR 34ANR 36ANR
38ANR 40ANR 42ANR 44ANR 46ANR 48ANR ― ―

External Appearance SiME341909EA
10 Part 1 General Information
2. External Appearance
2.1 Indoor Unit
Ceiling mounted cassette (Round flow with sensing) type
FXFSQ-AR
Slim ceiling mounted duct type (Standard series)
FXDQ-PD
FXDQ-ND
Ceiling mounted duct type
FXMQ-PB
FXMQ-AR
Wall mounted type
FXAQ-AR

SiME341909EA External Appearance
Part 1 General Information 11
2.2 Outdoor Unit
34, 36, 38, 40, 42, 44, 46, 48 HP
10, 12, 14, 16 HP
22, 24, 26, 28, 30, 32 HP
6, 8 HP
RXQ6ARYFK
RXQ8ARYFK
RXQ10ARYFK
RXQ12ARYFK
RXQ14ARYFK
RXQ16ARYFK
RXQ18ANRYFK
RXQ20ANRYFK
18, 20 HP
RXQ36ANRYFK
RXQ38ANRYFK
RXQ40ANRYFK
RXQ42ANRYFK
RXQ44ANRYFK
RXQ46ANRYFK
RXQ48ANRYFK
RXQ34ANRYFK
RXQ22ANRYFK
RXQ24ANRYFK
RXQ26ANRYFK
RXQ28ANRYFK
RXQ30ANRYFK
RXQ32ANRYFK

Combination of Outdoor Units SiME341909EA
12 Part 1 General Information
3. Combination of Outdoor Units
Note: 1. For multiple connection, the outdoor unit multi connection piping kit (separately sold) is required.
Capacity range 6 HP 8 HP 10 HP 12 HP 14 HP 16 HP 18 HP 20 HP
Model name RXQ6AR RXQ8AR RXQ10AR RXQ12AR RXQ14AR RXQ16AR RXQ18ANR RXQ20ANR
Outdoor unit 1 RXQ6AR RXQ8AR RXQ10AR RXQ12AR RXQ14AR RXQ16AR RXQ6AR RXQ8AR
Outdoor unit 2——————RXQ12ARRXQ12AR
Outdoor unit 3————————
Capacity range 22 HP 24 HP 26 HP 28 HP 30 HP 32 HP 34 HP 36 HP
Model name RXQ22ANR RXQ24ANR RXQ26ANR RXQ28ANR RXQ30ANR RXQ32ANR RXQ34ANR RXQ36ANR
Outdoor unit 1 RXQ10AR RXQ12AR RXQ10AR RXQ12AR RXQ14AR RXQ16AR RXQ10AR RXQ12AR
Outdoor unit 2 RXQ12AR RXQ12AR RXQ16AR RXQ16AR RXQ16AR RXQ16AR RXQ12AR RXQ12AR
Outdoor unit 3——————RXQ12ARRXQ12AR
Capacity range 38 HP 40 HP 42 HP 44 HP 46 HP 48 HP
Model name RXQ38ANR RXQ40ANR RXQ42ANR RXQ44ANR RXQ46ANR RXQ48ANR
Outdoor unit 1 RXQ10AR RXQ12AR RXQ12AR RXQ12AR RXQ14AR RXQ16AR
Outdoor unit 2 RXQ12AR RXQ12AR RXQ14AR RXQ16AR RXQ16AR RXQ16AR
Outdoor unit 3 RXQ16AR RXQ16AR RXQ16AR RXQ16AR RXQ16AR RXQ16AR
System capacity Number.
of units
Module Outdoor unit multi
connection piping kit 1
kW HP 6 8 10 12 14 16
16.0 6 1 ●
—
22.4 8 1 ●
28.0 10 1 ●
33.5 12 1 ●
40.0 14 1 ●
45.0 16 1 ●
50.4 18 2 ● ●
BHFP22P1006
56.0 20 2 ● ●
61.5 22 2 ● ●
68.0 24 2 ●●
73.0 26 2 ● ●
78.5 28 2 ● ●
85.0 30 2 ● ●
90.0 32 2 ●●
96.0 34 3 ● ●●
BHFP22P1516
101.0 36 3 ●●●
107.0 38 3 ● ● ●
113.0 40 3 ●● ●
118.5 42 3 ● ● ●
125.0 44 3 ● ●●
130.0 46 3 ● ●●
135.0 48 3 ●●●

SiME341909EA Capacity Range
Part 1 General Information 13
4. Capacity Range
4.1 Connection Ratio
Type Min. connection ratio Max. connection ratio
Single outdoor unit
50% 130%Double outdoor units
Triple outdoor units
Connection ratio = Total capacity index of the indoor units
Capacity index of the outdoor units

Capacity Range SiME341909EA
14 Part 1 General Information
4.2 Outdoor Unit Combinations
kW HP Capacity
index Model name Combination Total capacity index of connectable indoor units
Maximum number of
connectable indoor units
16.0 6 150 RXQ6AR RXQ6AR 75 to 195 9
22.4 8 200 RXQ8AR RXQ8AR 100 to 260 13
28.0 10 250 RXQ10AR RXQ10AR 125 to 325 16
33.5 12 300 RXQ12AR RXQ12AR 150 to 390 19
40.0 14 350 RXQ14AR RXQ14AR 175 to 455 22
45.0 16 400 RXQ16AR RXQ16AR 200 to 520 26
50.4 18 450 RXQ18ANR RXQ6AR + RXQ12AR 225 to 585 29
56.0 20 500 RXQ20ANR RXQ8AR + RXQ12AR 250 to 650 32
61.5 22 550 RXQ22ANR RXQ10AR + RXQ12AR 275 to 715 35
68.0 24 600 RXQ24ANR RXQ12AR + RXQ12AR 300 to 780 39
73.0 26 650 RXQ26ANR RXQ10AR + RXQ16AR 325 to 845 42
78.5 28 700 RXQ28ANR RXQ12AR + RXQ16AR 350 to 910 45
85.0 30 750 RXQ30ANR RXQ14AR + RXQ16AR 375 to 975 48
90.0 32 800 RXQ32ANR RXQ16AR × 2 400 to 1,040 52
96.0 34 850 RXQ34ANR RXQ10AR + RXQ12AR × 2 425 to 1,105 55
101.0 36 900 RXQ36ANR RXQ12AR × 3 450 to 1,170 58
107.0 38 950 RXQ38ANR RXQ10AR + RXQ12AR +
RXQ16AR 475 to 1,235 61
113.0 40 1,000 RXQ40ANR RXQ12AR × 2 + RXQ16AR 500 to 1,300
64
118.5 42 1,050 RXQ42ANR RXQ12AR + RXQ14AR +
RXQ16AR 525 to 1,365
125.0 44 1,100 RXQ44ANR RXQ12AR + RXQ16AR × 2 550 to 1,430
130.0 46 1,150 RXQ46ANR RXQ14AR + RXQ16AR × 2 575 to 1,495
135.0 48 1,200 RXQ48ANR RXQ16AR × 3 600 to 1,560