Data Video WM-1 Series User manual

WM-10

2
Table of Contents
WARRANTY ................................................................................................... 3
STANDARD WARRANTY .......................................................................................3
THREE YEAR WARRANTY .....................................................................................4
DISPOSAL ......................................................................................................4
INTRODUCTION.............................................................................................5
PARTS ASSEMBLY AND INSTALLATION ..........................................................5
PRE-WORK ........................................................................................................5
PROCEDURE.......................................................................................................7
INSTALLING PTR-10/10T.............................................................................. 11
INSTALLING PTC-150 ................................................................................... 13
FREQUENTLY ASKED QUESTIONS................................................................. 15
DIMENSIONS AND WEIGHT ......................................................................... 16
SPECIFICATIONS .......................................................................................... 17
SERVICE AND SUPPORT ............................................................................... 20
Disclaimer of Product & Services
The information offered in this instruction manual is intended as a guide only.
At all times, Datavideo Technologies will try to give correct, complete and
suitable information. However, Datavideo Technologies cannot exclude that
some information in this manual, from time to time, may not be correct or
may be incomplete. This manual may contain typing errors, omissions or
incorrect information. Datavideo Technologies always recommend that you
double check the information in this document for accuracy before making
any purchase decision or using the product. Datavideo Technologies is not
responsible for any omissions or errors, or for any subsequent loss or damage
caused by using the information contained within this manual. Further advice
on the content of this manual or on the product can be obtained by
contacting your local Datavideo Office or dealer.

3
Warranty
Standard Warranty
Datavideo equipment is guaranteed against any manufacturing defects for
one year from the date of purchase.
The original purchase invoice or other documentary evidence should be
supplied at the time of any request for repair under warranty.
The product warranty period beings on the purchase date. If the purchase
date is unknown, the product warranty period begins on the thirtieth day
after shipment from a Datavideo office.
All non-Datavideo manufactured products (product without Datavideo
logo) have only one year warranty from the date of purchase.
Damage caused by accident, misuse, unauthorized repairs, sand, grit or
water is not covered under warranty.
Viruses and malware infections on the computer systems are not covered
under warranty.
Any errors that are caused by unauthorized third-party software
installations, which are not required by our computer systems, are not
covered under warranty.
All mail or transportation costs including insurance are at the expense of
the owner.
All other claims of any nature are not covered.
All accessories including headphones, cables, batteries, metal parts,
housing, cable reel and consumable parts are not covered under warranty.
Warranty only valid in the country or region of purchase.
Your statutory rights are not affected.

4
Three Year Warranty
All Datavideo products purchased after July 1st, 2017
qualify for a free two years extension to the standard
warranty, providing the product is registered with
Datavideo within 30 days of purchase.
Certain parts with limited lifetime expectancy such as LCD panels, DVD
drives, Hard Drive, Solid State Drive, SD Card, USB Thumb Drive, Lighting,
Non-PCIe Card and third party provided PC components are covered for 1
year.
The three-year warranty must be registered on Datavideo's official website
or with your local Datavideo office or one of its authorized distributors
within 30 days of purchase.
Disposal
For EU Customers only - WEEE Marking
This symbol on the product or on its packaging indicates that
this product must not be disposed of with your other
household waste. Instead, it is your responsibility to dispose of
your waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of
disposal will help to conserve natural resources and ensure that it is recycled
in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
CE Marking is the symbol as shown on the left of this page.
The letters "CE" are the abbreviation of French phrase
"Conformité Européene" which literally means "European
Conformity". The term initially used was "EC Mark" and it was officially
replaced by "CE Marking" in the Directive 93/68/EEC in 1993. "CE Marking" is
now used in all EU official documents.

5
Introduction
WM-10 Professional Wall Mount is designed specifically for Datavideo
PTR-10/10T Robotic Pan Tilt Head as well as the PTZ camera series
(PTC-150/150T/200/200T). The two bubble level meters allow the user
to align the mounted device horizontally.
The four piece mounting kit is made of rugged metal and is easy to
install on any walls. The assembled mount can support up to a 100 kg
load.
Note: WM-10 is designed for PTR series of robotic pan tilt heads and
PTC series of PTZ cameras.
Parts Assembly and Installation
In this section, you will be shown how you can assemble and install
your kit.
Pre-work
1. First check you have all the parts listed in the table below.
No.
Part Names
Qty
1
Wall plate
1
2
Left bracket
1
3
Right bracket
1
4
Round rod
1
5
Base plate
1
6
M5x20 nickel plated hex socket cap screw
12
7
Expansion bolt
4
8
M5 screw
4
9
M3 x 10mm screw and spring washer (For
mounting PTR-10/10T)
4
10
M3 x 8mm screw (Additional mount for PTR-
10/10T
4

6
2. On the surface where the WM-10 is to be mounted, drill four holes
spaced according to the dimensions indicated in the diagram below.
Then follow the procedure in the next section to assemble and install
the WM-10.

7
Procedure
The diagram below is an exploded-view drawing of WM-10, and the
numbers correspond to the respective installation steps.
1
2
3
4
5
Bubble Level
Meter

8
1. Align the wall plate with the four holes drilled in Pre-Work then
use four expansion bolts to secure the wall plate. See the diagram
below.
2. Assemble the left bracket to the wall plate with two M5x20 nickel
plated hex socket cap screws as shown in the diagram below.

9
3. Assemble the right bracket to the wall plate with two M5x20 nickel
plated hex socket cap screws as shown in the diagram below.
4. Place the round rod in between the left and right brackets then
secure it in position by fastening two M5x20 nickel plated hex
socket cap screws to the respective holes on the brackets as
shown in the diagram below.

10
5. Insert the base plate between the left and right brackets then
secure it in position by fastening six M5x20 nickel plated hex
socket cap screws to the respective holes on the brackets as
shown in the diagram below. The inner rails on the right and left
brackets should allow you to move the base plate back and forth.
Please note that you can use the bubble level meter to check if the
base plate is properly aligned. If the bubble is at the center, the base
plate is horizontally aligned (perfectly levelled). If the bubble is on
either side, the base plate is tilted to the sides.

11
Installing PTR-10/10T
To mount the PTR-10/10T to the WM-10, first place it on the base
plate of the WM-10 such that the four screw holes at the bottom of
the PTR-10/10T base are aligned with the screw holes found in the
base plate as indicated in the diagram below.
Secure your PTR-10/10T with four M3 x 10mm screws and spring
washers.

12
If after installation, the PTR-10/10T vibrates, you may enhance the
installation by securing the base with four M3 x 8mm screws. The
additional screw holes are depicted in the diagram below.

13
Installing PTC-150
Before installation, first make sure you have the following:
PTC-150
Standard accessories of PTC-150
-Ceiling bracket
-M4 screw x 4
WM-10 wall mount
To mount the PTC-150 on the WM-10, use four M4 screws to secure
each of the upper and lower plates of the ceiling bracket to the base
plate of WM-10 and bottom of the PTC-150 respectively.
Upper
Plate
Lower
Plate
Screws

14
The WM-10 with the PTC-150 mounted is shown in the diagram below.

15
Frequently Asked Questions
This section describes problems that you may encounter while using
WM-10. See related items for suggested solutions. If problem still
exists, please contact your distributor or the service center.
No.
Problems
Solutions
1
PTR-10/10T vibrates after
installation.
If after installation, the PTR-
10/10T vibrates, you may
enhance the installation by
securing the base with four M3 x
8mm screws. The additional
screw holes are depicted in the
diagram below.

16
Dimensions and Weight
Unit: mm
Weight: 4.0 Kg (8.80 lb)
Maximum load: 100 Kg

17
Specifications
Model No.
WM-10
Name
Professional Wall Mount for Robotic Pan Tilt Head
Weight
4 kg (8.80 lb)
Dimensions
416 x 200 x 126 mm
Max. Load
100 kg
Applicable
Products
PTR-10 series
PTC-140 series
PTC-150 series
PTC-280 series
PTC-300 series

18
Notes

19
Notes

https://www.datavideo.com/product/WM-10
May-21.2021 Ver:E2
Datavideo Technologies Co., Ltd. All rights reserved 2020