Dayens Ampino User manual

Ampino
Mono Power Amplifier
User’s manual
www.dayens.rs rev.AM1

Thank you for purchasing the Ampino mono power amplifier.
We hope that you will enjoy it for many years.
For any questions or comments, or if we can assist you or support you in any way, please
don’t hesitate to contact us.
Please read the following instructions efore using this product.
Unpacking
Shipping oxes have een designed to protect their contents and special care has een
taken to prevent damage under normal shipping conditions. Mishandling should e
evident upon inspection of the carton shipping ox. If damage is found after visual
inspection, document the damage with photographs and contact the transport carrier and
Dayens immediately.
Placement
Ampino is designed for use inside homes.
It must e protected from the temperature extremes.
Avoid placing the unit in extremely hot locations such as near radiators or other heating
units or in a place su ject to excessive dust, mechanical shock and direct sunlight.
Device should not e placed on surface that may lock the top or ottom ventilation
openings. Never lock ventilation openings on top of the device.
Make sure that device has normal air flow for cooling purposes.
Device is attended to work in horizontal position only.
Do not place heavy o jects on the component.
Its location among the user’s audio components is not critical.
Installation and Setup
Connect speaker ca les to rear speaker terminals; there is one pair per amplifier.
You can use terminated ( ananas, spades) and un-terminated ca les ( are wire).
Please make sure that ca les aren’t shorted at speakers end. Speaker ca les should e
hand tightened down at the speaker output terminals, without excessive force.
Ampino is attended to work with most loudspeakers with impedance etween 4 and 16
Ohm.
For preamplifier or source (with volume control) connection you can use any RCA
(un alanced) interconnect ca les, recommended length is etween 0,5 and 1m.
The choice of a high quality interconnect and speaker ca les is recommended for est
sonic result.
For maximum safety we suggest that the power cord should e the last ca le installed on
your amplifier.

Operation and Powering up
Your new Ampino is ready for operation after all the ca les have een installed.
The Ampino is provided with functional and simple front panel control with very logical
and intuitive layout.
Ampino mono power amplifier should e the last powered ON device and also the first to
e powered OFF.
DO NOT unplug interconnect or loudspeaker ca les while the power remains ON.
Never remove/insert AC line cord when the unit is ON.
Unplug the power cord of this product from the wall outlet during lightening storms or if
you are not going to use it for a long period of time.
Front Panel Features
Power switch: Two position toggle switch.
Upper position: ON.
Lower position: OFF.
Down center green LED: Indicates that the device is powered ON.
Rear Panel Features
Speaker terminals: for connection of your speaker ca les.
Input terminal: for connecting your interconnect ca le.
IEC Power connector: for connecting power cord.

Warranty and Service
We are carefully manufacturing and testing our products with goal to keep the failure rate
to a minimum; however, it is possi le that something may go wrong.
If you have any pro lems with your product, contact us directly at [email protected] and
descri e your pro lem in detail.
Warranty covers normal function of the product and starts from the date of purchase.
Our warranty does not apply:
- to damage caused during transport or y accident, a use, misuse, misapplication, etc.
- to damage caused y service performed y unauthorized person;
- to a product or a part that has een modified in any way without our permission;
Customer will ear the expense of shipping the product to our service, including the
return shipment, and all taxes, duties, and other customs fees.
After expiry of the warranty period we will provide replacement parts and service.
All repairs performed y Dayens after expiry of the warranty period will e charged to
the owner and the cost will include only serviced/replaced parts and components and will
carry a 180-day warranty on parts and la or.
No User Servicea le Components Inside.

Specifications
This section descri es the asic specifications of the Ampino Mono at the time of writing
this manual.
Technical specifications
Power (Watt): 50 / 8 Ohm
100 / 4 Ohm
Num er of inputs (mono): 1
Input type: RCA (un alanced)
Frequency response (Hz): 1Hz - 200kHz
SNR (dB): >92
Dimensions (mm): 150x330x90
Weight (kg): 4
Specifications are subject to change without prior notice or obligation.
Proudly Designed, Engineered and Manufactured in Ser ia

www.dayens.rs
[email protected]
tel: [phone]
address: Centar 1, 15000 Ša ac, Ser ia