Delta-Opti HD-SDI tester User manual

CCTV Tester Manual
V2.10

Thank you for purchasing the CCTV security tester. Please read the manual before using the
CCTV tester and use properly.
For using the CCTV tester safely, please first read the「Safety Information」carefully in the
manual.
The manual should be kept well in case of reference.
Keep the S/N label for after-sale service within warranty period. Product without S/N label will
be charged for repair service.
If there is any question or problem while using the CCTV tester, or damages occurred on the
product, please contact our technical Department.

Content
1. SAFETY INFORMATION-------------------------------------------------------------------------------------1
2.INTRODUCTION------------------------------------------------------------------------------------------------3
2．1 GENERAL-----------------------------------------------------------------------------------------------------3
2.2 FEATURES------------------------------------------------------------------------------------------------------3
2.3 FUNCTION------------------------------------------------------------------------------------------------------5
2.3.1 Video signal testing--------------------------------------------------------------------------------------------5
2.3.2 HD SDI camera image input and output(*optional) -----------------------------------------------------5
2.3.3 VGA、HDMI input -------------------------------------------------------------------------------------------5
2.3.4 Video signal level test-----------------------------------------------------------------------------------------5
2.3.5 PTZ controller --------------------------------------------------------------------------------------------------5
2.3.6 Enhanced Color bar generator -------------------------------------------------------------------------------6
2.3.7 DC12V 2Aoutput power--------------------------------------------------------------------------------------6
2.3.8 Audio testing----------------------------------------------------------------------------------------------------6
2.3.9 Cable tester------------------------------------------------------------------------------------------------------6
2.3.10 PTZ controller-----------------------------------------------------------------------------------------------6
2.3.11 Data monitor ------------------------------------------------------------------------------------------------6
2.3.12 PTZ address scanning -------------------------------------------------------------------------------------6
2.3.13 Image magnification（10xZoom）---------------------------------------------------------------------7
2.3.14 Video snapshot------------------------------------------------------------------------------------------------7
2.3.15Video record----------------------------------------------------------------------------------------------------7
2.3.16 Video playback------------------------------------------------------------------------------------------------7
2.3.17 Cable scan (optional function refer to the last page) ---------------------------------------------------7
2.3.18 Port flicker-----------------------------------------------------------------------------------------------------7
2.3.19 IP address scan------------------------------------------------------------------------------------------------7
2.3.20 Link monitor---------------------------------------------------------------------------------------------------7
2.3.21 PING test-------------------------------------------------------------------------------------------------------8
2.3.22 POE tester------------------------------------------------------------------------------------------------------8

2.3.23 Digital multimeter (optional function refer to the last page)------------------------------------------8
2.3.24 Visualfault locator(optional function refer to the last page)------------------------------------------8
2.3.25 Optical Power Meter (optional function refer to the last page)---------------------------------------8
2.3.26 LED lamp----------------------------------------------------------------------------------------------------9
2.3.27 F1、F2 User-defined shortcut keys---------------------------------------------------------------------9
2.3.28 Video level meter---------------------------------------------------------------------------------------------9
2.3.29 TDR break-point and short-circuit measurement----------------------------------------------------- 10
2.3.30 USB 5V 2A power output(power bank)---------------------------------------------------------------- 10
2.4 ACCESSORIES-----------------------------------------------------------------------------------------------10
2.5 FRONT PANEL ---------------------------------------------------------------------------------------------- 11
3.OPERATION----------------------------------------------------------------------------------------------------14
3.1 Installing the Battery------------------------------------------------------------------------------------------- 14
3.2. Instrument connection ---------------------------------------------------------------------------------------- 15
3.3 OSD Menu------------------------------------------------------------------------------------------------------- 17
3.3.1 PTZ controller -------------------------------------------------------------------------------------------- 18
3.3.2 Color-bargenerator--------------------------------------------------------------------------------------- 21
3.3.3Video level meter----------------------------------------------------------------------------------------- 22
3.3.4 Video setting---------------------------------------------------------------------------------------------- 24
3.3.5 HD SDI Video input and output(*optional)--------------------------------------------------------- 24
3.3.6 VGA signal input ---------------------------------------------------------------------------------------- 25
3.3.7 HDMI signal input--------------------------------------------------------------------------------------- 26
3.3.8 PTZ address search -------------------------------------------------------------------------------------- 27
3.3.9 10x zoom image display and Video out-------------------------------------------------------------- 28
3.3.10 Photograph----------------------------------------------------------------------------------------------- 29
3.3.11 Video record--------------------------------------------------------------------------------------------- 29
3.3.12 Record playback---------------------------------------------------------------------------------------- 29
3.3.13 Cable Scan（optional）------------------------------------------------------------------------------ 30
3.3.14 PING Test------------------------------------------------------------------------------------------------ 31
3.3.15 Cable tester ---------------------------------------------------------------------------------------------- 32

3.3.16Port flicker------------------------------------------------------------------------------------------------ 33
3.3.17 Link monitor--------------------------------------------------------------------------------------------- 33
3.3.18IP address scan------------------------------------------------------------------------------------------- 34
3.3.19 PoE tester ------------------------------------------------------------------------------------------------ 34
3.3.20 Digital Multi-meter（optional）-------------------------------------------------------------------- 35
3.3.21 Optical Power Meter（optional）------------------------------------------------------------------ 41
3.3.22 Visual Fault Locator*（optional）-----------------------------------------------------------------43
3.3.23TDR Tester（optional）------------------------------------------------------------------------------- 43
3.3.24 Data monitor--------------------------------------------------------------------------------------------- 45
3.3.23 Device setting ------------------------------------------------------------------------------------------- 45
3.3.25 USB------------------------------------------------------------------------------------------------------- 46
3.4 DC12V 2A power output --------------------------------------------------------------------------------- 46
3.5 USB 5V 2A power output -------------------------------------------------------------------------------- 47
3.6 Audio input test--------------------------------------------------------------------------------------------- 48
3.7 LED lamp---------------------------------------------------------------------------------------------------- 48
4. Specifications----------------------------------------------------------------------------------------------------- 49
4.1 General Specifications------------------------------------------------------------------------------------- 49
4.2 Multimeter specifications: -------------------------------------------------------------------------------- 52
4.3 Optical power meter specifications --------------------------------------------------------------------- 55
4.4 Visual fault locator specifications----------------------------------------------------------------------- 56

Page.1.
1. Safety information
The tester is intended to use in compliance with the local rules of the electrical usage and avoid
to apply at the places which are inapplicable for the use of electrics such as hospital, gas station
etc.
To prevent the functional decline or failure, the product should not be sprinkled or damped.
The exposed part of the tester should not be touched by the dust and liquid.
During transportation and use, it is highly recommended to avoid the violent collision and
vibration of the tester, lest damaging components and causing failure.
Don’t leave the tester alone while charging and recharging. If the battery is found severely hot,
the tester should be powered off from the electric source at once. The tester should not be
charged over 8 hours.
Don’t use the tester where the humidity is high. Once the tester is damp, power off immediately
and move away other connected cables.
The tester should not be used in the environment with the flammable gas.
Do not disassemble the instrument since no component inside can be repaired by the user. If the
disassembly is necessary indeed, please contact with the technician of our company.
The instrument should not be used under the environment with strong electromagnetic
interference.
Don’t touch the tester with wet hands or waterish things.
Don’t use the detergent to clean and the dry cloth is suggested to use. If the dirt is not easy to
remove, the soft cloth with water or neutral detergent can be used. But the cloth should be
tweaked sufficiently.
About digital multimeter
Before using, you must select the right input jack, function and range.
Never exceed the protection limit values indicated in specifications for each range of
measurement.
When the meter is linked to a measurement circuit, do not touch unused terminals.
Do not measure voltage if the voltage on the terminals exceeds 660V above earth ground.

Page.2.
At the manual range, when the value scale to be measured is unknown beforehand, set the range
selector at the highest position.
Always be careful when working with voltages above 60V DC or 40V AC, keep fingers behind
the probe barriers while measuring.
Never connect the meter with any voltage source while the function switch is in the current,
resistance, capacitance, diode, continuity, otherwise it will damage the meter.
Never perform capacitance measurements unless the capacitor to be measured has been
discharged fully.
Never measure any of resistance, capacitance, diode or continuity measurements on live circuits.
About Visual fault locator：
To avoid serious eye injury, never look directly into the optical outputs of fiber optic network
equipment
Always replace protective dust cap on the detector port when the instrument is not being used.

Page.3.
2.Introduction
2．1 General
The CCTV tester with 7 inch HD LCD display, supporting VGA & HDMI input from DVR/ NVR,
easily and conveniently to test and set the DVR/ NVR. As an essential tool for HD-SDI camera testing,
it has 1 Channel SDI video input and 1 channel SDI video output. Meanwhile the tester can be used for
input and output the BNC video, PTZ control, DC12V /2A power output,Audio test, Color generator,
RS485 Data analysis, UTP Cable testing, Video snapshot , Video record and playback, Image
magnification etc. It can also be used for IP camera / PoE switch or other network device’s installing or
troubleshooting by offering IP address search, PING testing, PoE voltage testing, PoE port flickering
and link monitoring.
Besides, it is also a magic tools to find out the correct cable from the clutter cabling system and
diagnose the location of the cable’s short circuit and break-point. This advanced tester is developed for
the On-Site installation and maintenance of cctv security systems and network systems. Its easy
operation and portability makes it simple for a cctv technician or installer to install and maintain CCTV
systems, improving work efficiency by reducing time in the field.
2.2 Features
More than 9 languages optional ( English, Portuguese, German, French, Spanish, Italian,
Russian etc)
7inch HD LCD screen display, 800(RGB)x600
HD SDI digital camera image input and output (*optional)
VGA, HDMI signal input, easily and conveniently to test and set the DVR/ NVR.
DC12V 2A power output for camera
USB 5V 2A power out for mobile phone and other devices
LED Lamp, easy to operate at night
Micro SD card moveable
User-defined shortcut keys（F1 and F2）

Page.4.
LCD screen brightness/contrast/color Saturation adjustable
Automatically adapts and displays the video format of NTSC/PAL
Optical Power Meter, it can measure the optical power value (*optional)
Digital multimeter, it is used for the voltage current, Resistance, Diode, Capacitance
measurement (*optional)。
10xzoom, video image can be magnified to view the details, easy to use
Video record and playback ,Snapshot and save the current image as JPG file in the SD card
PING testing，test IP camera or other network devices’ ethernet port whether work normally,
and the IP address whether right
Video signal PEAK level, SYNC level, COLOR BURST chroma level measurement
Cable scan, send the specific signal, easily to find correct cable quickly from the clutter
cabling system.
IP address scan, quickly search the IP address for the connected IP camera and other network
devices
POE voltage measurement，test the PoE switch’s voltage to IP cameras, wireless AP device
and other PD devices
Device Port flicker，easy to find the connected PoE switch port by sending special signals, the
connected PoE port will flicker at special frequency.
Link monitor; check the setting IP address whether occupied.
TDR cable tester, diagnose the location of the BNC and network cable’s short circuit and
break-point (*Optional)
PTZ address scan, search up the ID of PTZ camera.
Network cable and Telephone cable testing, display the sequence of connection and the NO
of the LAN cable
Support RS232/RS485/RS422, Rate 600 ～115200bps adjustable
Multi-protocol. Supports more than thirty PTZ protocols. Such as PELCO-P, PELCO-D,
SAMSUNG
PTZ protocol analysis, control protocol command displays to check RS485 transmission
whether is normal, easy to find the fault device
PTZ control. Pan/tilts the P/T unit, zooms in/out the lens, adjusts the focus, aperture and
sets and the preset position

Page.5.
Audio input test, test the audio signal from pickup devices
Visual fault locator , to test fiber’s bending and breakage (*optional)
Lithium Ion Polymer Battery .The device employs advanced power control and protection
circuit. The device is high power-efficient, energy saving and environmental protection. It
can last 17 hours for normal use after charging for 7 -8 hours
Note:With "* " sign means function optional
2.3 Function
2.3.1 Video signal testing
The HD-SDI camera tester, features with built-in 7 inch HD LCD screen , full-view display, 800（RGB）
x600 resolution , easily and directly displays the camera image in top quality.
Supports PAL/NTSC, LCD screen brightness/Contrast/Color Saturation adjustable. It is suitable for the
outdoor installing and maintenance.
2.3.2 HD SDI camera image input and output(*optional)
1 channel SDI input and 1 channel SDI output, 7 inch HD LCD screen , 800（RGB）x 600 resolution,
supports HD camera in 1080P（25,30,50,60 frames）and 720P（25,30,50,60frames. Very convenient
and useful to install and troubleshoot the HD-SDI cameras.
2.3.3 VGA/HDMI input
1 channel VGA and HDMI signal input, used as a monitor or television, to receive the signals from
DVR/NVR , helping the engineers to debug and set DVR./NVR easily and conveniently
2.3.4 Video signal level test
Test video signal strength attenuation, longer video signal cable will cause the image to be dim, and
reduce the image dynamic range, video signal is too strong, it will cause the virtual shadow, and reduce
the sharpness of the image.
It also can real-display the video level value, if out of range, notices will be display in the screen.
2.3.5 PTZ controller
Display the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the controlling
parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set and call preset