Snoos V2 Keypad Manual

1
©Snoos Copyright 2017 Rev1.0
For updated information see www.snoos.com/support
Snoos V2 Keypad with NFC tags

2
©Snoos Copyright 2017 Rev1.0
For updated information see www.snoos.com/support
Installation and setup
Connect battery:
Pull out the strip to connect the battery
Mounting and use:
The keypad is best mounted nearby the entrance door. It is used to arm/disarm the Snoos
Home alarm system by a NFC tag or a pin code. Up to 5 NFC tags can connect to the keypad.
Factory codes
Learn procedure - Alarm system
------------------------------------------
Enroll of the keypad in the alarm system:
•Open the app
•Select ‘Devices’ in the menu.
•Press ‘+Add’
•Select the keypad in the device list.
•Press ’Enroll’.
•The alarm gateway will wait for a confirmation from the new keypad for 60 sec.
On the Keypad:
1. Press *
2. Enter the user code. (Default user code is ‘1111’)
3. Press ‘Disarm’ (Disarm is the button with the open pad lock).
Repeat the operations 1-3 to have the signal send to the alarm gateway twice.
Factory user PIN code: 1111

3
©Snoos Copyright 2017 Rev1.0
For updated information see www.snoos.com/support
Setup NFC Tags
--------
Enroll new NFC Tag:
•Press “*”
•Enter “PIN Code” (Default PIN Code: 1111)
•Press “8”
•Press “#”
E.g.: *11118#
•The keypad enters enroll mode and confirms with a long beep.
•Swipe the tags.
•Enroll mode closes after 5 sec.
Delete all NFC tags:
•Press “*”
•Enter “PIN Code” (Default PIN Code: 1111)
•Press “7”
•Press “#”
E.g.: *11117#
•The keypad deletes all tags and confirms with a long beep.
Successful operation: Keypad confirms with one beep.
Failed operation: Keypad confirms with three beeps.

4
©Snoos Copyright 2017 Rev1.0
For updated information see www.snoos.com/support
Change of PIN codes
------------------------------
Change of user PIN code:
•Press *
•Enter existing PIN code: (Default: ’1111’)
•Press “9”
•Enter new 4 digit PIN code
•Press #
Reset lost PIN code:
•Remove the batteries
•After 60 sec, insert the batteries
•Immediately hereafter - Enter *111194 + New PIN code + #
•Enter new 4 digit PIN code
Successful operation: Keypad confirms with one beep.
Failed operation: Keypad confirms with three beeps.

5
©Snoos Copyright 2017 Rev1.0
For updated information see www.snoos.com/support
Change of batteries
---------------------
Change Batteries:
3 pcs AAA batteries needed.
•Remove 6 screws
•Lift off the cover
•Replace the batteries
•Notice the small socket on the PCB
•Carefully place fit the pins in of the upper part in the socket
•Mount 6 screws.

6
©Snoos Copyright 2017 Rev1.0
For updated information see www.snoos.com/support
Daily use
------------
Arm and Disarm of the alarm system, using the user PIN code:
Arm alarm:
•Press “*”
•Enter the user PIN code (Default is ‘1111’)
•Press “Arm”(The button with a closed pad lock) ”.
Arm alarm in Home mode:
•Press ”*”
•Enter the user PIN code (Default is ‘1111’)
•Press ”Home alarm button (The button with a person in a House)”.
Disarm alarm:
•Press ”*”
•Enter the user PIN code (Default is ‘1111’)
•”Disarm (The button with an open pad lock)”.
Arm and Disarm of the alarm system using the NFC tag:
(The NFC tag should be enrolled first.)
Arm alarm:
•Press ”*”
•Swipe the NFC tag one time over the reading field on the keypad.
Disarm alarm:
•Press ”*”
•Swipe the NFC tag twice over the reading field on the keypad.

7
©Snoos Copyright 2017 Rev1.0
For updated information see www.snoos.com/support
www.snoos.com