Cavius 3004-001 User manual

PLEASE READ THIS USER GUIDE CAREFULLY
THERMAL HEAT ALARM
THE WORLD’S SMALLEST

PLEASE READ THE USER
GUIDE CAREFULLY BEFORE
INSTALLATION AND RETAIN
FOR FUTURE USE.
CAVIUS Thermal Heat Alarm
Part Code: 3004-003/10020
Model: 3004-001
Recess Kit Part Code: 11010
For large text option and maintenance guide visit
cavius.co.nz/resources
cavius.com.au/resources

1.
TEST/HUSH
BUTTON
ALARM AUDIBLE ALERT

2.
The best locations in your home to install
the thermal heat alarm:
• Kitchen
• Garage or Workshop
• Washing and drying area or laundry.
Additional heat alarms will increase the
safety. The NZ and Australian Fire Services
recommend alarms in every bedroom,
hallway and living area for early re detection.

3.

Placement: The thermal heat alarm is area
specic. The alarm should be placed on the
ceiling and near where the potential re risks
may occur.
Never install directly above the oven / hob /
stove.
4.

For kitchen installation:.
CEILING
MINIMUM 50cm
5.

Installation of heat alarm:
Info: The label on the product
must not be removed due to
important information.
Option 1 – Standard base
1. Use the mounting
base ring to mark the
screw holes on the ceiling.
MARK UP
SCREW HOLES
WITH A PEN
6.

USE THE
ENCLOSED
SCREWS AND
PLUGS FOR
INSTALLATION
CLICK THE HEAT
ALARM FIRMLY INTO
THE BASE TO ACTIVATE
7.

Option 2 – Recess Kit
1. Place the Cover Ring on the area where
you wish to install the heat alarm, trace
around the inside of the ring.
HOLE SAW
DRILL REQUIRED.
44mm - 48mm
8.

2. Using your hole saw (44mm-48mm), cut a
hole into the surface. CAUTION: Ensure there
is no wiring or any electrical equipment behind
the surface you are drilling your hole into.
INSERT RECESS KIT
MOUNTING BASE INTO
THE HOLE AND SECURE
WITH SCREWS
PLACE COVER RING
AROUND THE RECESS
KIT MOUNTING BASE
CLICK THE HEAT ALARM
FIRMLY INTO THE
BASE TO ACTIVATE
9.

Test Button: After mounting the alarm, test
the heat alarm by pushing the test button
(which is the entire bottom of the alarm).
The alarm should produce a loud sound.
10.

Heat alarm signal: The heat alarms have
a visual and acoustic signal. In the passive
state, the LED will ash every 48 seconds to
indicate normal function. In alarming state
the LED will ash and the alarm will emit a
sweeping sound pattern designed to alert
occupants.
11.

Hush function: In case of unintentional or
false alarms, press and hold the hush button
for 2 seconds (which is the entire bottom
of the alarm). This will mute the alarm for
10 minutes, after which time the alarm will
automatically resume its normal function.
12.

Maintenance: Test the heat alarm once per
month by pushing the test button. The heat
alarm should produce a loud alarm tone.
Place the heat alarm where it is reachable in order
to test the battery and complete maintenance.
If the heat alarm does not work when the test
button is pushed, please check our Trouble
Shooting Guides at;
cavius.co.nz and cavius.com.au
13.

FUNCTIONAL INFORMATION
Type of alarm: CAVIUS thermal heat alarm
detects rapidly increased temperature level
and absolute heat level.
Alarm signal: Heat alarm activation is
indicated by a series of repeated tones.
The minimum sounds level is 85 dB at 3
metres.
Battery: Powered by a
non-replaceable CR123A
3V, 1600mAh with 10-year
life (included).
14.

Low battery indicator: A short acoustic
“beep” will sound and the LED will ash every
48 seconds when the battery is near the end
of its life. In this stage it will continue for a
minimum 30 days.
Please replace thermal heat alarm:
You must change the heat alarm after 10 years
usage, or if the heat alarm has suered any
damage. The heat alarm is not active unless it
is inserted in the mounting base.
Always test the heat alarm after inserting into
the mounting base, allow 5 seconds before
testing.
15.

Disposal: For product, please dispose
properly at end of life. The alarm can be
recycled at an electronic waste recycling
centre.
Other information:
• Do not paint the heat alarm.
• Note the local country regulations regarding
installation of heat alarms in new buildings.
16.

The CAVIUS Thermal Heat Alarm is
designed for areas where a re will be
more ame and heat than smoke; areas
such as kitchens, garages, laundries
and workshops. This device is activated
when it senses a rapid increase in room
temperature.
Tested to comply to the
standard of system heat alarms
EN54-5 class A1/R.
17.
127480 Rev1

Developed & Manufactured by:
Aps
Julsøvej 16 - DK8600 Silkeborg
cavius.com - [email protected]
Manufactured in P.R.C.
Distributor information:
for New Zealand - CAVIUS Nano Ltd.
58a Poplar Lane, Papamoa 3187, NZ.
www.cavius.co.nz
for Australia - CAVIUS Australia
14/30 Octal Street, Yatala, QLD 4207, Australia.
www.cavius.com.au
18.