Delta ATE-GT5R User manual

Vehicle 4G OBD Data Terminal
Quick
Installation
User
Manual
(Version V1.0)
Thank you very much for using GPS TRACKER, the user manual will guide how to operate this
product, please read it carefully before using it in order to get the correct method of operation. If
the appearance, color and accessories of this product are modified, please refer to the actual
product. The manufacturer is not liable for faults and omissions which in the user manual.

1、Product functions & Parameters
1.1 Product functions
Location inquiry, geo-fence, over-speed alarm, power-off alarm, historical route playback,
Vehicle fault diagnosis, OBD data detection.
1.2 Parameters
QUECTEL EC20 module (different modules for different countries, the following are the frequency
bands for EC20, different countries with different modules and frequency)
4G:LTE FDD:B1/B3/B5/B8
LTE TDD：B34/B38/B39/B40/B41
3G :WCDMA:B1/B8
:TD-SCDMA:B34/B39
2G :CDMA:BC0 900/1800MHz
●Wide voltage input range: 9 - 35V;
●Location time: average warm start:≤3sec(open sky)
Average cold start:≤35sec(open sky)
●Device dimensions:59mm × 45mm × 22mm;
●Location accuracy:≤10 meters;
●Working Temp:-20℃- 75℃
2、Product accessories and LED light status
2.1 Accessories:
Standard: device, user manual
2.2 Device LED light status
2.2.1 RED LED (OBD Working status)
Light status
Meaning
light
OBD working
off
OBD Sleep/power off
2.2.2 Yellow LED (GSM signal status)
Light status
Meaning
Quick flash
GSM initialization
light
GPRS normal communication/online
off
GSM sleep/power off
2.2.3 Blue LED (GPS signal status)
Light status
Meaning
Quick flash
GPS signal searching
light
GPS location finished
off
GPS sleep/power off

3、Installation instructions
3.1 Preparation before installation:
1, Open the box and check whether the device and the accessories are complete, otherwise
please contact your dealer.
2, SIM card selection, the device works with Micro SIM card, and support full Netcom band.
3, SIM card installation, SIM card corner inside, chip face to the side with shrapnel, which can
help to hold the card.
Note: (1) Before installing or removing the SIM card, please switch off the device;
(2) Should activate the GPRS function of the SIM card;
(3) Should activate the caller ID function; (activate or not according to the
functions you chose.)
(4) If your SIM card required you to input the SIM PIN, please refer to your
mobile phone user manual to turn off the SIM PIN function.
(5) Please ensure that the SIM card is valid.
3.2 Installation
Device with standard OBDII socket
4、SMS commands and instructions:
Send SMS command from user’s SIM card number to the SIM card number which inside the
GPS device.
The commands in the following SMS command list are in English input format, and the
letters are case-sensitive according to the instruction requirements.
Common commands
SMS command format
Device reply
User parameter query
CXZT
Version、ID、IP, etc…
Revise IP
IP+blank+IP+blank+port
Example：IP 106.3.230.234 8185
SET IP OK

Device restart
CQ
CQ OK
Restore factory settings
FORMAT
FORMAT OK
ACC ignition upload time interval
FREQ,123456,20
SET OK
ACC off upload time interval
STATIC,123456,20
SET ACCONTIME OK
Revise APN
APN123456 CMMTM
SET APN OK
Revise APN user name
APNUSER123456 USER
SET APNUSER OK
Revise APN password
APNPASSWD123456 PASSWORD
SET APNPASS OK
5、App operation
5.1 Login location service platform
Users can login to the global positioning service platform provided by the dealer, to check the
location and status of the vehicle, and perform corresponding operations. Please consult your
dealer for the service platform website.
5.2 Platform login on computer:
Enterprise users and fleet management users please select the username to log in. User name
and password are set by the dealer, please contact your dealer for user name distribution!
For individual users, please login with the device ID number. The ID number is on the device body
and also on the package box. When logging in to the platform, please select IEIM/License number
to log in. The default password is: 123456
Android APP download, please scan the QR code on the computer, and if Apple mobile phone,
please search the APP name in the App store.
5.3 Functions introduce
5.3.1 Real-time tracking：
Click the “Real-Time tracking” icon to enter the corresponding page to view the vehicle
status, VIN code, driving route, speed, direction, street view and other information.
Introduction of command operation
Idle speed alarm setting: set the idle speed warning, when the vehicle has speed, but lower than
the preset idle speed, send alert message.
Water temperature range setting: set the coolant temperature range, when the coolant
temperature higher than the preset temperature, send alert message.
Low voltage alarm setting: set low voltage warning for the battery, when the battery voltage
lower than the preset voltage, send alert message.
Over-speed alarm setting: Set the over-speed warning, when the speed faster than the preset
speed, send alert message.
Continuous driving time warning alarm: set continuous driving fatigue warning, when driving
time longer than preset time, send alert message.

Minimum rest time: Set the rest time. If engine off time shorter than preset time, send alert
message.
Inflection point Completion angle: Set the corner replenishment angle. When the device angle
changes bigger than the pre-set value, then report this data.
ACC off upload interval: Set the upload interval after ACC off. When ACC off, the device upload
according to the pre-set time interval.
ACC on upload interval: set the upload interval when ACC on, the device upload according to the
pre-set time interval
Revise Password: Set the modification of login password.
6. Trouble shooting
If the device can’t be connected to the background server after first time installation, and the
background server shows it is offline, please check the installation correct or not.
If you have any questions for the operation, please refer to the following questions and
solutions; if you still can't solve the problem, please contact your dealer.
Common Problems
Reasons
Solutions
Poor signal
Test at areas where there are
high buildings or underground
parking lots, where radio
waves cannot be sent or
received normally.
Use it at a good signal place
platform shows device
not activated after first
installation
Main power supply connected
correct or not
Do not connect to the main control
line of the vehicle
SIM inserted not correct
Check the SIM card
LED status
Check if the indicator is blinking or
steady
SIM without GPRS activated or
SIM card out of charge.
Please contact carrier to activate
GPRS or charge
Platform map shows
incorrect location
GPS no location
Please go to outdoor place where
GPS signal good
Vehicle did not move after
installation
Please drive the vehicle on the
road
ACC connected or not
Connect the device and turn on
ACC
Platform shows the main
power disconnect
Poor power supply connection
Check whether the power supply
line of the device connected
correct or not
Platform shows device
offline
SIM card out of charge of
GPRS was canceled
Please check your SIM card
Weak signal area
Please try again at good signal area

Warranty card
Special statements:
1. If there is any technical modification for this product in the future, no further
notice.
2. If the appearance or color of the product were changed, please refer to real
product.
3. The warranty card is only applicable to product with IMEI number listed as below.
4. Please keep this card in good condition. Please present this card and the original
purchase receipt when you apply warranty.
5. Please refer to the table below for the warranty range.
This card is the basic proof of the warranty. Please fill in the card carefully and
keep it in good condition.
User Name
Telephone
Number
Address
Model No.
IMEI
Purchasing
Date
Commercial
invoice No.
Seller Name
Seller Address
Seller contact
number
1. One year from the date of purchase, the non-human damage failure is
guaranteed for one year;
2. Any of the following conditions is not covered by the warranty, but can be
repaired if you pay the cost
(1) Exceeding the warranty period;
(2) Damage caused by unauthorized disassembly or repair without the
authorization of our company;
(3) immersed in water and the circuit board was burnt;
(4) Damage caused by improper installation, use, maintenance or storage;
(5) damage of outer casing caused by the improper use;
(6) The IMEI number of the product is torn or blurred;
(7) The warranty card and product model No. not match, or the warranty card
was altered;
(8) Damage caused by force majeure.