Denon Professional DN-700C Technical manual

DN-700C
Latest Firmware Version: A-2.35
Release Date: July 1, 2015
Update Process and Verification
Important: Before updating to the latest firmware, please make sure your DN-700C is using Firmware Version
A-2.14 or later. If it is not, please update to A-2.14 before updating to A-2.33: follow all of the steps below using
the DN700CFW.bin file, and then repeat the same procedure using the DN700CFWA.bin file.
To update the firmware on your DN-700C:
1. Unzip the contents of the downloaded .zip file to your Desktop.
2. Transfer the DN700CFWA.bin file from that .zip file to the root directory of a USB storage device.
3. Make sure your DN-700C is securely connected to a power outlet and is powered off, and then insert the
USB storage device into it.
4. Power on DN-700C.
5. DN-700C's display will show the new firmware version number. Confirm the version number is correct.
6. To continue with the update, turn the Jog Wheel on the front panel to select OK, and then press the Jog
Wheel.
During the update process, do not power off DN-700C or disconnect it from the power outlet. Doing so can
damage the unit.
To cancel the operation instead, turn the Jog Wheel on the front panel to select Cancel, and then press the
Jog Wheel.
7. Allow the update process to complete, which may take approximately 1 minute. The display may go dark
during this time. After the update is completed, DN-700C will automatically restart. Remove your USB
storage device, and delete the .bin files.
Your DN-700C now has the newest firmware.
To check the firmware version on your DN-700C:
1. With the DN-700C powered on and stopped, press the Menu key.
2. Select 06 Utility and press the Jog Wheel.
3. Select 03 Firmware Version and press the Jog Wheel. The installed firmware version will appear in the
display.

Changes
Firmware Version A-2.35 (July 2015)
•Added auto-power down functionality for ErP.
Firmware Version A-2.33 (September 2014)
•Added ability to manually select whether or not the pitch value is recalled.
•Added ability to assign the button to change the pitch.
•Fixed an issue where the preset file occasionally did not load completely.
Firmware Version A-2.32 (May 2014)
•Added hotlist file (.ppl) function created by RC-F400S loading automatically.
•Added ability to forcibly eject disc by pressing Shift and Eject simultaneously when the Shift button mode
is set to Momentary.
•Improved CD reading performance.
•Improved detection performance of USB device when starting up.
•Fixed an issue where continuous playback of DLNA contents can stop in a certain environment.
•Fixed an issue where TCP/IP packet response can be occasionally delayed.
Firmware Version A-2.30 (March 2014)
•Fixed the function of the D&M RC Communication format commands.
•Improved CD playback performance.
•Fixed an issue where a pop noise occasionally occurred when finishing media playback.
•Fixed the functionality of Extended Communication Format (MIDI).
Firmware Version A-2.25 (January 2014)
•Added Web Remote customization function.
•Fixed an issue where transferring to Utility and System settings via Web Remote display in iOS device did
not work.
•Improved CD reading performance.
•Fixed the function that stores Hotlist files by using RC-F400S.
•Fixed an issue where the RC-F400S display sometimes displays Wait… popup continuously after inserting
USB media.
Firmware Version A-2.23 (November 2013)
•Added MIDI command to change playback media.
•Fixed MIDI command error.
•Fixed an issue where occasional pop noises occurred when changing FS or media.
•Fixed an issue where the unit can freeze after playing specified wave files.
•Fixed an issue where playback status changes to Cue after changing media from CD to USB.
•Fixed an issue where network media folders did not appear on Web Remote display when Play Range is
set to All.
•Fixed an issue where the pitch button would sometimes not work.

Firmware Version A-2.13 (September 2013)
•Added Enter and Back buttons to Web Remote GUI.
•Added displayed message to Web Remote GUI when playback status is not Stop or Cue in the Preset or
System setting display.
•Added displayed message to Web Remote GUI when the selected media is unavailable.
•Added displayed message to Web Remote GUI when the unit encounters an error.
•Added support for Mozilla Firefox browser.
•Changed display of track number in Web Remote GUI so the number flashes when using the Next Track
Reserve function.
•Changed Load to Load File and Enter to Enter Folder in Web Remote GUI.
•Added pitch and volume reset buttons to Web Remote GUI.
•Added display of machine name to browser tag area.
•Changed UPnP icon design.
•Added ability to switch power control and machine detection (from the project manager) in the Preset
menu.
•Added end monitor function.
•Added Japanese font.
•Fixed OLED contrast range.
•Fixed other minor issues.
Firmware Version A-1.10 (May 2013)
• Fixed an issue where the RC-F400S update function did not work.
Technical Support
For additional help, visit denonpro.com/support.