Diamond Audio Technology HEX Series User manual

OWNERS MANUAL
System covered:
S6.0mx3
6 (160mm)
Midbass Component Add-On
Converts an S400/500 system to passive 3- ay operation.
All manuals and user guides at all-guides.com
all-guides.com

The following diagram shows a typical connection of the S6.0mx3 Midbass Add-On
to the S400 or S500 systems. In this manner, a f lly passive 3-way speaker
system may easily be assembled. Optionally, the RAF o tp t of the primary HEX
crossover may still be sed to a gment the front stage so nd. The Sx3 crossover
feat res selectable highpass freq encies of 200 or 400Hz @ 6dB/oct, pl s level
controls to balance the bass/mid/high so nd. For Bi-amping thro gh the Sx3 (not
shown), simply connect the additional amp channels to the corresponding INPUT 2
terminals. Then, move the internal switches #3 & #4 to the BIAMP=ON position.
FAILURE TO SO MAY CAUSE DAMAGE TO THE AMPS. Note: INPUT 1 passes
a dio to the WOOFER o tp t, INPUT 2 to the HIGHPASS o tp t.
+-
+-
- +
+ - + - + - + -
LPI HPI LPO HPO REARTWEETERWOOFERINPUT
+
-+-+-+-
Sx3
HEX primary
S6.0mx3 Midbass Add-On
Rear Fill Driver
(optional RAF)
HEX T eeter
HEX Midrange
S6.0m
Midbass
(amp not
supplied)
All manuals and user guides at all-guides.com

S6.0m
HEX Cone
Midbass/Woofer
.21
[5.2]
2.30
[58.5]
6.28
[159.5]
6.85
[174.0]
5.35
[136.0]
5.91
[150.0]
3.79
[96.3]
1.11
[28.3]
2.07
[52.5]
Technical
Sx3
250Hz Midbass
Crossover
All manuals and user guides at all-guides.com

© 1999 Diamond Audio Technology, Inc. - All rights reserved. Part No. 7 5-5351 Rev. B http://www.diamondaudio.com
Diamond Audio Technology, Inc.
3030 Pennsylvania Ave.
Santa Monica, CA 90404
Tel: [phone]
Fax: [phone]
 L I M I T E D W A R R A N T Y S T A T E M E N T 
Diamond Audio Technology, Inc. (DAT) warrants all DAT products to be free of defects in material and workmanship for a period of one
(1) year from the date of original purchase provided they are purchased from an authorized DAT retailer in the United States. However,
the effective warranty period will be three (3) years if the products were purchased from and installed by an authorized DAT retailer.
WHAT IS COVERED: Parts and labor to effect repair or, at the sole discretion of DAT, replacement of either any malfunctioning or
defective part(s) or the entire system should the system or any component part(s) thereof fail to perform as designed. Includes return
freight via ground transportation to destinations within the United States.
WHAT IS NOT COVERED: Installation or setup and repair or replacement of the system or any parts thereof which, in DATs judgement,
fail or become damaged as a result of negligence, improper use, abuse, unauthorized modification or service, improper or inadequate
packaging during shipment, installation by a non-authorized dealer, accident, or use for any purpose other than those for which this
product was originally intended, or where the models serial number has been removed, altered or defaced.
WHO IS COVERED: Original purchaser so long as they reside in the United States and can provide proof of the original date of purchase
(e.g., store receipt) from an authorized DAT retailer.
OUTSIDE THE UNITED STATES: Customers outside the United States should contact their local sales office to obtain information on
prices, exchange unit availability, instructions, service and warranty/non-warranty repairs.
REPAIR OR REPLACEMENT UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. DAT SHALL NOT BE
LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY
ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANT-
ABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF
THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may
also have other rights that may vary from state to state.
HOW TO OBTAIN WARRANTY SERVICE: In the event a DAT product should require servicing, you should (a) visit an authorized DAT
retailer or (b) call the DAT Service Dept. at (31 ) 582-8942. To be eligible for warranty service within a three (3) year period, the
accompanying receipt of original purchase from an authorized DAT retailer must specifically note that dealer installation was provided.
Product returned for repair/service must be properly packaged and clearly marked with the Return Authorization (RA) number issued by
DAT. If the RA number is not clearly marked on the package or no RA number was issued by DAT, the product may be refused upon
delivery. DAT does not assume responsibility for lost or misdirected product.n
All manuals and user guides at all-guides.com