Dipol PRB-1 User manual

INSTALLATION INSTRUCTIONS
PRB-1
ISSUED: DEC. 2011
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
Projector Ceiling Mount
10kg
(22lbs)
MAX
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
11

21
NOTE: Read the entire instruction manual before you start installation and assembly. Component Checklist
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experiences and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• Never exceed the maximum load capacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Package W
ST6.3x50 (x3)
W-A
concrete anchor (x3)
W-B
decorative cover (x1)
B
15cm extension pipe (x1)
E
projector plate (x1)
C
mounting leg (x3)
D
ceiling plate (x1)
A
M4x14
M-A
(x4) M5x20
M-B
(x3) 4mm Allen key (x1)
M-D
M6x12 (x3)
M-C
adjustable part (x3)
M-E
M6 washer (x3)
M-F
adjustable part (x2)
M-G
spacer (x6)
M-H
D6 washer (x6)
W-C
8cm extension pipe (x1)
F

WARNING
• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finder
is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installer must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
4
3
1a. Wood Ceiling Mounting:
50mm/2" ø 4.5mm
ø 3/16"
2
1
Drill three
pilot holes
3
Screw the
ceiling plate
onto the ceiling
• When installing ceiling mounts on cinder block, verify the actual concrete thickness is at
least 1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure
to mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
1b. Solid Brick and Concrete Block Mounting:
50mm/2" ø 10mm
ø 3/8"
12
W-A
Drill three
pilot holes
Screw the
ceiling plate
onto the ceiling
W-A
W-B
W-C
W-C

3. Attaching Mounting Legs and the Projector Plate
65
2. Installing Decorative Cover and Extension Pipe
Press in the two
bolts at the same
time and connect
extension pipe to
ceiling plate.
Run the projector
cables through
the pipe.
Turn bolt outside
for maximum
safety.
M-D
or
or
M-B
M-H
M-B
M-B
M-H
M-H
3a.common mounting
Locate the projector ’s mounting points.
Screw mounting legs onto the projector.
DO NOT TIGHTEN ALL SCREWS AT THIS TIME.
E or F

3b. for Toshiba projectors
8
M-D
3b-1. For Toshiba projectors
M-C
7
M-D
M-C
M-F
W-C
M-B
M-H
M-H
M-F
W-C
M-G
M-A
Place the projector plate on the mounting legs, as close as to projector center of gravity as possible.
Slightly adjust the arms to fit slots pattern on the projector plate. And then use screws and washers
to fix the projector plate.
Tighten the all mounting screws which secure the mounting legs to the projector at this time.
Attach the adjustable part to
projector using screws.
Locate the projector ’s mounting points.
Screw mounting legs onto the projector.
DO NOT TIGHTEN ALL SCREWS
AT THIS TIME.
Place the projector plate on the mounting
legs, as close as to projector center of
gravity as possible. Slightly adjust the
arms to fit slots pattern on the projector
plate. And then use screws and washers
to fix the projector plate.
Tighten the all mounting screws
which secure the mounting legs
to the projector at this time.

109
3b-2. for Philips projectors 4. Hang the Projector onto the Ceiling Mount
5. Pitching Angle Adjustment
Adjust to desired location or tilt.
Press in the two bolts at the same time and connect projector plate to pipe.
Important: Make sure the projector is correctly hooked before releasing the projector.
360°
-5° ~ +5°
Turn bolt outside for maximum
safety.
M-D
M-D
M-C
M-F W-C
M-B
M-H
M-H
M-E
Insert adjustable part into
projector.
Locate the projector ’s mounting points.
Screw mounting legs onto the projector.
DO NOT TIGHTEN ALL SCREWS
AT THIS TIME.
Place the projector plate on the mounting
legs, as close as to projector center of
gravity as possible. Slightly adjust the
arms to fit slots pattern on the projector
plate. And then use screws and washers
to fix the projector plate.
Tighten the all mounting screws which
secure the mounting legs to the projector
at this time.