Farnell PS-UTTS32B User manual

Model PS-UTTS32B
Universal Table Top Stand/Base
Read through ALL instructions before commencing installation.
STOP
Retain all packaging in case the product needs to be returned.
Contents may vary from photography / illustrations.
You will not need all these parts, so expect there to be some left over depending upon
the specification of your TV.
This product is intended for indoor use only. Use of this product outdoors could lead
to failure and personal injury.
15kg
33lbs

Boxed Parts
A
B
D
H2
H1
H1
H2
M4
16mm
R1x4
M8
16mm
R8x4
M4
25mm
R2x4
M8
25mm
R9x4
M4
50mm
R3x4
M8
45mm
R10 x4
M6
25mm
R6x4
Q1x12
45mm
M6
R7x4
Q2x4
M6
16mm
R5x4
P2x4
M5
25mm
R4x4
P1x4
M5
Jx8
M6
12mm
Lx4 Nx2 Kx4
M6
Mx4
M10
Ox2
C
M5
12mm
Ix8
E
F
Gx2
Tools Recommended
5mm

1
If width Xis greater than mm or height Ygreater than mm, OR if the
distance from the bottom fixing holes to the bottom of your TV is more than mm,
STOP installation now and contact the customer helpline.
200 200
200
X50 - 200mm
Y
50 - 200mm
R4
M5 =
R5/R6/R7
M6 =
R8/R9/R10
M8 =
R1/R2/R3
M4 =
You are provided with diameters of TV fixing screws
Determine the screw diameter that fits and remember for step .
4
3
, M4, M5, M6 and M8.
Bottom
Measure the TV fixing holes Width and Height

2
Use the option that fits your TV
X50mm x Y50mm X75mm x Y75mm X100mm x Y100mm
X100mm x Y200mm X200mm x Y100mm X200mm x Y200mm
Y
X
100
mm
75
mm
50
mm
50mm
75mm
100mm
Preparing the TV Mounting Plate
OPTION 1
OPTION 2 OPTION 3 OPTION 4
OPTION 1

Y
X
100
mm
200mm
Y
X
200
mm
100mm
Assemble as shown
at the end of this section.
OPTION 2
Assemble as shown
at the end of this section.
OPTION 3

Top
Adaptor assembly method.
(Example shown is 200 x 200 fixings)
M5
Jx8
M5
12mm
Ix8
Y
X
200
mm
200mm
D
H2
H1
H1
H2
I
J
OPTION 4
Assemble as shown
at the end of this section.

3
WARNING
For TVs with irregular / obstructed back
For TVs with flat / unobstructed back
TV TV TVTV
After completing step you will have fittings left over, please keep for future reference
3
Q1/Q2
Fitting the TV Mounting Plate
No Spacers Spacers

Attach the bracket to the back of your TV using suitable screw, reducer and spacer combinations
R1 - R4
Q1
Q2
If required
Top
R1 - R10
R4-R7
R8-R10
P2
P1
R1-R3
Q1
Q2
If required
Do you need P2or P1?
OPTION 1
OPTION 2, 3 & 4

4
Top
K
A
Attach the feet to the bottom of the glass base
Assemble the column
B
E
F
i ii
A
iii x2
GO
Dull side
Assemble the Base

5mm
iv v
vi
G
O
G
Push your fingers through the cable
management hole and use them to
guide G into position.